• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.213-217
• /
• 1999

An expert system is developed for rational and efficient design of multi-component injection molding which is a fairly new manufacturing technique to produce plastic parts by injecting two or more materials sequentially using multiple injection units in a single machine into a single rotary mold. The knowledge base used in the present design system is primarily composed of two parts ; knowledge from domain expert and knowledge from CAE analysis. The present expert system has hour main modules ; general design guidelines for injection molding specific guidelines for multi-component injection molding redesign guidelines from the result of the CAE analysis and finally troubleshooting for multi-component injection molding. To show the validity of the present design methodology two shop floor design problems were tested ; design and fabrication of timing belt cover and power window's assist knob by using multi-component injection molding.

• Transactions of Materials Processing
• /
• v.15 no.8 s.89
• /
• pp.628-632
• /
• 2006

The gate mark in injection molded part is a kind of surface defects. The formation of gate mark has been investigated in this study. SEM photographs and surface roughness have been examined to study gate mark. The specimens were molded for various injection conditions, such as injection temperature, mold temperature, and injection speed. Gate diameter and mold surface condition were also molding variables. Gate marks were reduced as injection speed and mold temperature increased. Gate diameter and injection temperature did not affect the gate marks. No etching of mold surface showed no gate marks for any molding conditions.

• Transactions of Materials Processing
• /
• v.19 no.5
• /
• pp.296-304
• /
• 2010

It is still needed to study the effect of process conditions on the final properties of injection-molded parts for producing precision optical products. Especially, the optical anisotropy, i.e., birefringence, is a significant factor to affect the function of many optical components. In the present study we have focused on the effect of holding and compression processes on the birefringence remaining in the transparent disc by examining the gap-wise distribution of birefringence and extinction angle. As a result, two extra birefringence and extinction peaks near the center in thickness direction showed the effect of holding pressure, which came from the flow in packing stage. However, more uniform birefringence distribution than injection-only cases could be found in injection/compression cases. Depends on the process condition even the flow reversal could be found from the distribution of extinction angle. Finally, graphical representation of optical indicatrix was added for better understanding the final structure of injection-only and injection/compression cases.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.983-988
• /
• 2004

In the present study, the effects of orthogonal ribs on structural warpage during injection molding process were investigated. Basic ribbed models for the evaluation of degree of warpage were introduced and designed. Injection molds for these models are manufactured based on the full 3D CAD/CAM technology and specimens are prepared for experiment. Numerical analysis using commercial plastic injection molding analysis software was also performed to compare the results with experimental ones. The variations of materials and parameters such as injection time, mold temperature, melt temperature, holding time were considered in the present work. It was shown that orthogonal ribs have significant effect on the reduction of warpage during the injection molding process.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.4
• /
• pp.478-486
• /
• 2005

Statement of problem : Fracture and dimensional change of an acrylic resin denture are a rather common occurrence. Purpose : The purpose of this study was to compare differences in dimensional changes and flexural strength of separate maxillary complete dentures after immediate deflasking by injection molding and conventional compression processing. Material and method: To evaluate dimensional stability, the maxillary dentures were fabricated by using different materials and methods. Lucitone 199(Dentsply Trubyte. york, pennsylvania, USA) and Vertex(Dentimex, zeist, Netherlands) were used as materials. Compression and injection packing methods were used as processing methods. The impression surface of the dentures was measured by 3D Scann-ing System(PERCEPTRON USA) and overlapped original impression surface of the master cast. To evaluate flexural strength, resin specimens were made according to the different materials, powder/liquid ratio and processing methods. Flexural strength of the complete resin specimens (64mm$\times$10mm$\times$3.3mm) were measured by INSTRON 4467. (INSTRON, England) The data was analyzed by ANOVA, t-test and Tukey test. (p<.05 level of significance) Result: The results were as follows 1. There was no significant differences between master model and denture base for each group in overall dimensional changes. 2. Palatal area was more stable than flange or alveolar area in dimensional stability. but. there was no significant differences among each area. 3. Materials and power/liquid ratio had an effect on flexural strength. (P<.05) Especially materials was most effective. (P<.05) 4. Lucitone 199(powder/liquid ratio followed by manufacturer's direction) showed higher flexural strength than Vertex. Conclusion : Dimensional stability or flexural strength are affected by materials rather than packing techniques.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.781-783
• /
• 2009

We achieved high efficiency and long lifetime in small-molecule organic light-emitting diodes using a blend of polyaniline-based conducting polymer and a perfluorinated ionomer as a hole injection layer (HIL). The HIL formed by single spin coating greatly enhanced the surface work function and thus the hole injection from the anode, which resulted in great improvement in device luminous efficiency. We find that the solution processed HIL outperforms the conventional vacuum-deposited small molecule HIL in terms of the device performance.

• Plant Journal
• /
• v.9 no.2
• /
• pp.42-45
• /
• 2013

The worldwide issue of greenhouse gas reduction has recently drawn great attention to carbon capture and storage(CCS). In this study, we developed a 10,000 ton/year pilot injection plant for geological storage of carbon dioxide. Major components of the pilot plant include a pressure pump, a booster pump, and an inline heater to bring liquid carbon dioxide into its supercritical state. The test results show that the pilot plant readily achieves the injection pressure and temperature, showing satisfactory control performance. The overall power consumption is 2,000 ~ 2,500 W, more than 75% of which consumed by the pressure pump. This study will facilitate varied research on greenhouse gas reduction as the only domestically developed system for geological injection.

• Transactions of Materials Processing
• /
• v.6 no.6
• /
• pp.489-499
• /
• 1997

The injection molding process is analyzed to get the information on the mold design parameters and the optimum process conditions for automotive plastic front fender. The gate position, runner size and cooling channel are determined by the estimation of the flow balance, packing time, uniform cooling and shrinkage and warpage in the injection molding analyses. The procedure can be used in the mold design in the early stage when developing plastic parts.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.641-650
• /
• 2002

For the production of complicated plastic parts in a cycle, a mold is needed.. The basic tasks of a mold are accommodation and distribution of the resin, shaping and cooling the melt and ejection of the molding. To achieve these goal a mold has several important parts and we classified types of molds. The 6 different major functions of a mold are explained and several types of molds are shown in her. I hope these explanation will help to understand injection molds for a design engineer.

• Korean Journal of Materials Research
• /
• v.12 no.1
• /
• pp.68-74
• /
• 2002

The lead has to be removed for the recycling of copper alloy. The lead cannot be removed from the copper alloy by oxidation. It can be removed by the evaporation because of its high vapor pressure. However, rare information is found on removal of lead from copper alloy. The purpose of present work is to provide a fundamental knowledges on the removal of lead from the copper alloy by evaporation. Gas injection was made in molten copper alloy, and the evaporation rate of lead was measured. The influence of Ar gas flow rata(2~4 L/min), initial contents of lead(2~4wt%Pb), temperature(1200~140$0^{\circ}C$) was investigated based on the thermodynamic and the kinetics. The rate constant is increased with increasing flow rate of Ar and temperature. Though amount of lead removed is increased with higher initial lead concentration, the rate constant is not changed significantly. The activation energy is estimated from the temperature dependence of the rate constant. Also removal of lead from the copper by adding chloride was made for the comparison.