• Journal of Environmental Health Sciences
• /
• v.19 no.4
• /
• pp.44-50
• /
• 1993

This paper has concentrated on estimating the improvement of sludge dewaterability for the application of ozone in sewage treatment plant sludge. The experiment for the study was conducted by batch reactor, contacting ozone (5.0 g O$_3$/hr/l) to waste sludge and measured the Specific Resistance to Filtrate (SRF) varying pH, pressure and reaction time of ozone. And then checked the dissolved solids concentration of flitrate. The results of experiment were as follows: 1. When the total solids concentration of excess sludge was 9, 000 mg/l, the optimum injection rate of ozone was 5.0 g O$_3$/hr/l, and then pressure was 50 cm Hg for the measuring SRF. 2. In the range of pH 3~5, the effect of ozone injection was excellent, but it was unsatisfactory in the range of pH 9~11. Therefore, the ozone injection by acidifying pH level was effective in improving the dewaterability of sludge. 3. It was estimated that the dissolved solids concentration of flitrate was increased in proportion to the injection rate of ozone.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.867-876
• /
• 2020

This paper proposes a neutral-point voltage ripple reduction of high frequency injection sensorless control of IPMSM fed by a three-level inverter. The high frequency voltage injection method has been successfully applied to sensorless control for IPMSM at low speed region. In the process of high frequency voltage injection sensorless control for IPMSM, the neutral-point voltage ripple is increased. It should be reduced because it distorts the output current and decreases a life time of DC-link capacitor. The proposed method in this paper reduces the neutral-point voltage ripple by compensating the reference voltage, and the compensation value is calculated simply with reference voltages and currents. The effectiveness of the proposed method is verified by simulation results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.4
• /
• pp.447-453
• /
• 2016

The reduction technologies of exhaust gas from both the off-road engine and on-road vehicles are important. It is possible to apply various combustion technologies with engines after the application of a treatment technology to this field. In this study, main injection timing, pilot injection timing, and exhaust gas recirculation (EGR) rate were selected as the experimental parameters whose effects on the emission of exhaust gases and on the fuel consumption characteristics were to be determined. In the experiment, the emission of nitrogen oxide (NOx) and Smoke, and the Torque at the same fuel consumption level, were measured. The experimental data were analyzed using the Taguchi method with an L9 orthogonal array. Additionally, analysis of variation (ANOVA) was used to confirm the influence of each parameter. Consequently, the level of each parameter was selected based on the signal-to-noise ratio data (main injection timing, 3; pilot injection timing, 3; EGR rate, 2), and the results of the Taguchi prediction were verified experimentally (error: NOx, 10.3 %; Smoke, 6.6 %; brake-specific fuel consumption (BSFC), 0.6 %).

• Molecules and Cells
• /
• v.22 no.2
• /
• pp.189-197
• /
• 2006

Prolactin (PRL) is a pituitary hormone involved in various physiological processes, including lactation, mammary development, and immune function. To further investigate the in vivo and comparative endocrine roles of PRL, mouse PRL cDNA fused to the cytomegalovirus promoter, was introduced into muscle by direct injection. Previously we studied the function of rat PRL using the same protocol. PRL mRNA was detected in the muscle following injection by RT-PCR and subsequent Southern blot analysis. PRL was also detected and Western blot analysis revealed a relatively high level of serum PRL. In the pCMV-mPRL-injected female mice, the estrous cycle was extended, especially in diestrus stage and the uterus thickening that was shown in normal estrous stage was not observed. In the pCMV-mPRL-injected male mice, new blood vessels were first found at 5 weeks of age and fully developed blood vessels were found after 8 weeks in the testis. The number of Leydig cells increased within the testis and the testosterone level in serum was observed high. Finally, the number of white blood cells (WBCs) increased in the pCMV-mPRL-injected mice. The augmentation of WBCs persisted for at least 20 days after injection. When injection was combined with adrenalectomy, there was an even greater increase in number of WBCs, especially lymphocytes. This increase was returned normal by treatment with dexamethansone. Taken together, our data reveal that intramuscularly expressed mouse PRL influences reproductive functions in female, induces formation of new blood vessels in the testis, and augments WBC numbers. Of notice is that the Leydig cell proliferation with increased testosterone was conspicuously observed in the pCMV-mPRL-injected mice. These results also suggest subtle difference in function of PRL between mouse and rat species.

• Food Science of Animal Resources
• /
• v.40 no.6
• /
• pp.1055-1065
• /
• 2020

This study investigated the effects of brine injection and high hydrostatic pressure (HHP) on the quality characteristics of pork loin. Brine with ionic strength conditions (0.7% vs 1.5% NaCl, w/v) were injected into pork loins, and the meat was pressurized up to 500 MPa for 3 min. As a quality indicator, moisture content, color, cooking loss and texture profile analysis (TPA) of pork loins were estimated. Based on the results, brine with low ionic strength (0.7% NaCl) resulted in low injection efficiency and high cooking loss, although, it improved tenderness of pork loin at moderate pressure level (~200 MPa). While high ionic strength condition (1.5% NaCl injection) lowered the hardness of pork loins at relatively high HHP level (400-500 MPa), it also caused high cooking loss. To commercialize the brine injected pork loins, it was necessary to regulate brine compositions, which was not evaluated in this study. Nevertheless, the present study demonstrated that brine injection followed by moderate pressure (200 MPa) could improve the tenderness of pork loins without causing other major quality losses.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.49 no.6
• /
• pp.334-338
• /
• 2000

Even though it is not practical, yet there is a trend of the researches related to the anesthesia on the determination of depth of anesthesia and level of consciousness in the view point of neurophysiological aspects. That is, quantification of physiological signals which represent human brain function and pharmacological response could be used to find the level of consciousness based on the changes in physiological signals. This research was performed to analyze the relationship between parameters extracted from LAEP(long latency auditory evoked potential) and the amount of sedatives injected to the patients. Seventeen patients were participated for the experiment. Two different sedatives, midazolam and diazepam, were injected intramuscularly, and LAEPs caused by 1KHz and 2KHz auditory tone bust were obtained. It was found that amplitude of extracted parameters from LAEP, N100 and P300, were reduced as dose of sedatives were increased. Results of this study could be used for extracting more meaningful index and establishing algorithm for predicting changes of level of consciousness induced by sedatives.

• Journal of Soil and Groundwater Environment
• /
• v.25 no.1
• /
• pp.12-24
• /
• 2020

This study was conducted to examine an artificial recharge system, which was considered to be an alternative for securing additional groundwater resources in a high-density greenhouse region. An injection well with a depth of 14.0 m was placed in an alluvial plain of the zone. Eight monitoring wells were placed in a shape of dual circles around the injection well. Aquifer tests showed that the aquifer was comprised with high-permeable layer with hydraulic conductivities of 1.5×10^-3~2.4×10^-2 cm/sec and storage coefficients of 0.07~0.10. A step injection test resulted in a specific groundwater-level rising (Sr/Q) values of 0.013~0.018 day/㎡ with 64~92% injection efficiencies. Results of the constant-rate injection test with an optimal injection rate of 100 ㎥/day demonstrated an enormous storage capacity of the alluvial aquifer during ten experimental days. To design an optimal recharge system for an artificial recharge, the high-permeable layer should be isolated by dual packers and suitable pressure should be applied to the injection well in order to store water. An anisotropy ratio of the alluvial aquifer was evaluated to be approximately 1.25 : 1 with an anisotropy angle of 71 degrees, indicating intervals among injection wells are almost the same.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.6
• /
• pp.898-904
• /
• 2006

Effects of sodium bicarbonate (SBC) injection on meat quality and functionality of porcine M. longissimus lumborum were investigated. Fifteen pigs ($100{\pm}5kg$) were randomly selected at a commercial slaughter plant. After slaughtering the loins were dissected from the carcass before chilling at approximately 30 minutes post mortem. The loins were divided into four cuts for sample treatment, and SBC of 0.25 M, 0.40 M and 0.75 M was injected (2% w/w) using a syringe. As SBC injection level was increased, muscle pH increased significantly (p<0.05). SBC injection decreased lightness ($L^*$) values on the surface of muscle. Moreover, with injection of SBC, drip loss %, cooking loss % and shear force were significantly (p<0.05) decreased, whereas WHC and $Na^+$ content were significantly (p<0.05) increased. From panel testing of uncooked pork loin, no significant differences (p>0.05) were found in aroma, off-flavor and drip between injection of SBC at different levels and the control, although color and acceptability were significantly lower (p<0.05) in control pork loin compare with injection of SBC at 0.75 M. In cooked pork loin from the panel test, aroma, flavour, off-flavour and juiciness were found to be similar (p>0.05) on all treatments, but tenderness and acceptability were significantly higher (p<0.05) with injection of SBC at 0.75 M than for control loin. Myofibrillar protein solubility of muscles treated with SBC was significantly (p<0.05) higher than that of the control, although no significant differences (p>0.05) were found in sarcoplasmic protein solubility between the treatments. These results indicated that SBC injection into pre-rigor porcine M. longissimus lumborum could improve ultimate pork quality characteristics such as meat color, water-holding capacity, and could inhibit muscle protein denaturation due to an increase in muscle pH.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.380-380
• /
• 2010

Currently, organic light-emitting diodes (OLEDs) have been proven of their readiness for commercialization in terms of lifetime and efficiency. In accordance with emerging new technologies, enhancement of light efficiency and extension of application fields are required. Particularly inverted structures, in which electron injection occurs at bottom and hole injection on top, show crucial advantages due to their easy integration with Si-based driving circuits for active matrix OLED as well as large open area for brighter illumination. In order to get better performance and process reliability, usually a proper buffer layer for carrier injection is needed. In inverted top emission OLED, the buffer layer should protect underlying organic materials against destructive particles during the electrode deposition, in addition to increasing their efficiency by reducing carrier injection barrier. For hole injection layers, there are several requirements for the buffer layer, such as high transparency, high work function, and reasonable electrical conductivity. As a buffer material, a few kinds of transition metal oxides for inverted OLED applications have been successfully utilized aiming at efficient hole injection properties. Among them, we chose 2 nm of $WO_3$ between NPB [N,N'-bis(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] and Au (or Al) films. The interfacial energy-level alignment and chemical reaction as a function of film coverage have been measured by using in-situ ultraviolet and X-ray photoelectron spectroscopy. It turned out that the $WO_3$ interlayer substantially reduces the hole injection barrier irrespective of the kind of electrode metals. It also avoids direct chemical interaction between NPB and metal atoms. This observation clearly validates the use of $WO_3$ interlayer as hole injection for inverted OLED applications.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.911-917
• /
• 2015

The objective of this work focuses on the analysis of injection rate and macroscopic spray behavior characteristics with injection pressures as well as combustion and exhaust emission characteristics with injection timing and injection pressure by using a common rail single-cylinder diesel engine. The injection rate was measured by applying the Bosch method, and macroscopic spray behavior characteristics were analyzed with a constant-volume vessel and a high-speed camera. In addition, combustion and emission characteristics were analyzed in a common-rail single-cylinder diesel engine with precise control of fuel injection timing and pressure. For injection pressures of 30MPa and 50MPa, the injection rate was higher at 50 MPa, and the spray development (penetration) was also higher in the same elapsed time. The peak in-cylinder pressure and rate of heat release showed a tendency to decline as injection timing was delayed, and the peak in-cylinder pressure and rate of heat release were slightly higher for higher injection pressures. Higher injection pressures also reduced the mean effective pressure, while the indicated mean effective pressure and torque increased as injection timing was delayed to TDC. Nitrogen oxides had a peak level at injection timings of $BTDC20^{\circ}$(30MPa) and $BTDC15^{\circ}$(50MPa); carbon monoxide emissions were reduced by delaying injection timing from $BTDC30^{\circ}$.