• Journal of Powder Materials
• /
• v.26 no.4
• /
• pp.311-318
• /
• 2019

The objective of this study is to investigate the influence of powder shape and densification mechanism on the microstructure and mechanical properties of Ti-6Al-4V components. BE powders are uniaxially and isostatically pressed, and PA ones are injection molded because of their high strengths. The isostatically compacted samples exhibit a density of 80%, which is higher than those of other samples, because hydrostatic compression can lead to higher strain hardening. Owing to the higher green density, the density of BE-CS (97%) is found to be as high as that of other samples (BE-DS (95%) and P-S (94%)). Furthermore, we have found that BE powders can be consolidated by sintering densification and chemical homogenization, whereas PA ones can be consolidated only by simple densification. After sintering, BE-CS and P-S are hot isostatically pressed and BE-DS is hot forged to remove residual pores in the sintered samples. Apparent microstructural evolution is not observed in BE-CSH and P-SH. Moreover, BE-DSF exhibits significantly fine grains and high density of low-angle grain boundaries. Thus, these microstructures provide Ti-6Al-4V components with enhanced mechanical properties (tensile strength of 1179 MPa).

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.6_2
• /
• pp.737-744
• /
• 2021

An investigation is conducted to study a solid-liquid mixture vertically upward hydraulic transport of solid particles by non-Newtonian fluids in the Mud system. Rheology of particulate suspensions in viscoelastic fluids is of importance in many applications such as particle removal from surfaces, transport of proppants in fractured reservoir and cleaning of drilling holes, etc. In this study a clear acrylic pipe was used in order to observe the movement of solid particles. Annular velocities varied from 0.4 m/s to 1.2 m/s. The mud systems which were utilized included aqueous solution of sodium carboxymethyl cellulose (CMC) solutions. Main parameters considered in the study were inner-pipe rotary speed, fluid flow regime and particle injection rate. Solid volumetric concentration and pressure drops were measured for the various parameters such as inclination angle, flow rate, and rotational speed of inner cylinder.

• Clinical Pain
• /
• v.18 no.2
• /
• pp.121-125
• /
• 2019

Arthritis of hip joints deteriorates the quality of life in ankylosing spondylitis (AS) patients. Secondary to the articular inflammatory process, the shortened hip-girdle muscles contribute to the decreased joint mobility which may lead to the functional impairment. As the limitation of range of motion (ROM) usually progress slowly, clinicians regard it as a chronic condition and prescribe long-term therapy. However, by short-term intensive multimodal treatment, a 20-year-old man diagnosed as AS with severely limited hip joint ROM who relied on crutches doubled the joint angle and could walk independently only within 2 weeks. The combination included intra-articular steroid injection, electrical twitch obtaining intramuscular stimulation, extracorporeal shock wave therapy, heat, manual therapy, and stretching exercises. The management focused on the relaxation of hip-girdle muscles as well as the direct control of intra-articular inflammation. Hereby, we emphasize the effectiveness of intensive multimodal treatment in improving the function even within a short period.

• Journal of ILASS-Korea
• /
• v.28 no.2
• /
• pp.75-88
• /
• 2023

In this paper, the atomization characteristics of bi-swirl coaxial injectors for a 420 N-class bipropellant thruster were investigated. Three types of injectors, namely closed-type, open-type, and screw-type, were manufactured and designed to have the same spray angle and injection pressure drop. Water was used as a simulant, and cold-flow tests were conducted under ambient temperature and pressure conditions. Since the inner and outer injectors were designed to be the same type, only the inner fuel injectors that were easy to measure were used. Using a phase doppler particle analyzer, the velocity and diameter of atomized droplets were measured. Closed-type swirl injector exhibited droplet distributions with relatively high velocities and small SMD compared to the other two injectors. Open-type swirl injector formed droplets with reverse velocities in the center region and had a large recirculation zone. Screw-type swirl injector showed a sharp decrease in droplet velocity and size with radial distance from the liquid film breakup point. For the same design requirements, the closed-type swirl injector has superior atomization performance.

• The Journal of Engineering Geology
• /
• v.23 no.4
• /
• pp.329-340
• /
• 2013

A geologic survey of the Bukpyeong and Pohang basins, as candidate basins for the geological storage of $CO_2$, was performed to evaluate storage capacity and security. To analyze the mechanical stability of the storage reservoir and cap rocks, we measured the porosity, seismic velocity, uniaxial strength, internal frictional angle, and Young's modulus of core samples recovered from the two basins. It is costly and sometimes impossible to conduct tests over the entire range of drill holes, and continuous logging data do not yield the mechanical parameters directly. In this study, to derive the mechanical properties of geologic formations from the geophysical logging data, we determined the empirical relations between the physical properties (seismic velocity, porosity, and dynamic modulus) and the mechanical properties (uniaxial strength, internal friction angle) of the core samples. From the comparison with our core test data, the best fits to the two basins were selected from the relations suggested in previous studies. The relations between uniaxial strength, Young's modulus, and porosity of samples from the Bukpyeong and Pohang basins are more consistent with certain rock types than with the locality of the basins. The relations between the physical and mechanical properties were used to estimate the mechanical rock properties of geologic formations from seismic logging data. We expect that the mechanical properties could also be used as input data for a modeling study to understand the mechanical instability of rock formations prior to $CO_2$ injection.

• Korean Journal of Food Science and Technology
• /
• v.45 no.1
• /
• pp.40-46
• /
• 2013

The present study was performed to increase the availability of sweet (Ipomoea batatas) and to develop dinner roll with the reducing ability of blood glucose levels. Different contents of lyophilized sweet potato powder (SPP) were added in dinner roll. Compare to the control group, batter density, a value, hardness, and cohesiveness of the SPP-treated groups were significantly increased while dough expansion rate, baking loss rate, L value, and Hue angle were significantly decreased. Twenty four Sprague-Dawley rats were administered with the SPP-treated diet for 4 weeks after diabetes was induced with the injection of streptozotocin. The blood glucose concentration of the SPP-treated group was significantly lower than that of the control. Although the SPP-treated groups possessed the ability of reducing blood glucose level, the sensory qualities were inferior to the control. Thus, follow-up study was required to improve the sensory characteristics as well as the texture properties.

• Journal of Astronomy and Space Sciences
• /
• v.26 no.4
• /
• pp.451-466
• /
• 2009

While substorms are known to generally occur under southward IMF conditions, they can sometimes occur even under northward IMF conditions. In this paper, we studied the substorms that occurred in May, 2000 to 2002 to examine some statistical characteristics of the IMF and solar wind associated with northward IMF substorms. We focused on the cases where two or more substorms occurred successively under northward IMF conditions. Also, by checking Sym-H index associated with each of the substorms we determined whether or not there is any association of such northward IMF substorm occurrence with storm times. We also examined statistical properties at geosynchronous altitude in terms of magnetic field dipolarization and energetic particle injection. The following results were obtained. (i) Most of the northward IMF substorms occurred under average solar wind conditions. The majority of them occurred within 2 hrs duration of northward IMF Bz state, but there are also a nonnegligible number of substorms that occurred after a longer duraiton of northward IMF Bz state. (ii) While most of the substorms occurred as isolated from a magnetic storm time, those that occurred in a magnetic storm time show a higher average value of IMF and solar wind than that for the isolated substorms. (iii) About 55% of the substorms were associated with the IMF clock angle that can possibly allow dayside reconnection, and the other 45% were associated with more or less pure northward IMF conditions. Therefore, for the latter cases, the energy input from the solar wind into the magnetosphere should be made by other way than the dayside reconnection. (iv) For most of the substorms, the magnetic field dipolarizations and energetic particle injections at geosynchronous altitude were identified to be generally weak. But, several events indicated strong magnetic field dipolarizations and energetic particle injections.

• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.50-59
• /
• 2006

The risk of fault reactivation in the Gippsland Basin was calculated using the FAST (Fault Analysis Seal Technology) technique, which determines fault reactivation risk by estimating the increase in pore pressure required to cause reactivation within the present-day stress field. The stress regime in the Gippsland Basin is on the boundary between strike-slip and reverse faulting: maximum horizontal stress $({\sim}\;40.5\;Mpa/km)$ > vertical stress (21 Mpa/km) ${\sim}$ minimum horizontal stress (20 MPa/km). Pore pressure is hydrostatic above the Campanian Volcanics of the Golden Beach Subgroup. The NW-SE maximum horizontal stress orientation $(139^{\circ}N)$ determined herein is broadly consistent with previous estimates, and verifies a NW-SE maximum horizontal stress orientation in the Gippsland Basin. Fault reactivation risk in the Gippsland Basin was calculated using two fault strength scenarios; cohesionless faults $(C=0;{\mu}=0.65)$ and healed faults $(C=5.4;\;{\mu}=0.78)$. The orientations of faults with relatively high and relatively low reactivation potential are almost identical for healed and cohesionless fault strength scenarios. High-angle faults striking NE-SW are unlikely to reactivate in the current stress regime. High-angle faults oriented SSE-NNW and ENE-WSW have the highest fault reactivation risk. Additionally, low-angle faults (thrust faults) striking NE-SW have a relatively high risk of reactivation. The highest reactivation risk for optimally oriented faults corresponds to an estimated pore pressure increase (Delta-P) of 3.8 MPa $({\sim}548\;psi)$ for cohesionless faults and 15.6 MPa $({\sim}2262\;psi)$ for healed faults. The absolute values of pore pressure increase obtained from fault reactivation analysis presented in this paper are subject to large errors because of uncertainties in the geomechanical model (in situ stress and rock strength data). In particular, the maximum horizontal stress magnitude and fault strength data are poorly constrained. Therefore, fault reactivation analysis cannot be used to directly measure the maximum allowable pore pressure increase within a reservoir. We argue that fault reactivation analysis of this type can only be used for assessing the relative risk of fault reactivation and not to determine the maximum allowable pore pressure increase a fault can withstand prior to reactivation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.137-145
• /
• 2004

Limestone zone in korea have been distributed to diagonal line so that it is wide from the Gangwondo to the Jeonlanamdo. The limestone cavity and fractured zone were formed by chemical weathering. Limestone cavity and fractured zone was reinforced with cemented milk(w/c=60%)by high pressure jet grouting by tripple -pipe to establish bridge foundation on the ground condition like limestone cavity. To analyze property of limestone and solid of cement milk(w/c=65%), mixed solid of cement, core NX size in the limestone cavity and fractured zone and compressive strength. Seismic tomograpy exploration was pcrforn1cd to analyze deformation modulus of limestone. The analysis suggests that deformation modulus of limestone has effect on uniaxial compressive strength, seismic velocity, seismic elasticity modulus. Average static elasticity modulus of limestone is $5.08{\times}10^5kgf/cm^2$, cement and coal mixed solid is $0.25{\times}10^5kgf/cm^2$, $0.095{\times}10^5kgf/cm^2$. Average seismic velocity of limestone is 5.240m/sec, cement and coal mixed solid is 2,211.3m/sec, 1,447.5m/sec. Average uniaxial compressive strength of limestone was $1,221.3kgf/cm^2$ and limestone specimen mixed with cement milk and solid of cement milk mixed with coal were $125.22kgf/cm^2$, $35kgf/cm^2$ each other. Average friction angle of limestone was $49.14^{\circ}$ and limestone specimen mixed with cement milk and solid of cement milk mixed with coal were $38.39^{\circ}, 25.83^{\circ}$ each other. Average cohesion of limestone was $137.7kgf/cm^2$ and limestone specimen mixed with cement milk and solid of cement milk mixed with coal were $23.5kgf/cm^2$, $15.5kgf/cm^2$ each other. Average deformation modulus of limestone was $2.84{\times}10^5kgf/cm^2$ and limestone specimen mixed with cement milk and solid of cement milk mixed with coal were $0.4{\times}10^5kgf/cm^2, 0.12{\times}10^5kgf/cm^2$ each other. It was analyzed that the elasticity and uniaxial compressive strength, seismic velocity of solid of cement milk mixed limestone pieces and coal had an highly interrelation regardless of existence of limestones pieces and coal but it had shown that limestones had an lower interrelation. In case of field seismic velocity and deformation of limestone, SIC solid of cement milk mixed with coal and limestone pieces had an highly interrelation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.9-14
• /
• 2020

Four developed patents have applied for a new type of Composite Cyclone Scrubber followed by the previous research (Cho and Kim, 2017), including dust reducing fan with filters. Regarding target installation and maintenance cost, 64% reduction for investment costs (6.2 billion won vs. 17 billion won) compared to existing road pollution reduction system, while social benefit costs increase by 43% compared to existing road pollution reduction measures (72.6 billion won vs. 50.8 billion won). The composition of the device is an air blower type spiral guide vane, and an injection pressure collecting dust efficiency. A nozzle varies Injection angle and contact range, spray liquid species (waterworks, salty water). The proposed patent tests are circulation water Time-by-Time Spray and collected 41.4% more increased micro dust since the sprayed water meets contaminated gas due to the 45° degree colliding, which is 141% increased conventional dust collector. (Ratio of collection over 85%). As regards the source of collection liquid, circulated rainwater and well water, we expect a huge amount of energy and economically saved eco-friendly system in our patent. Finally, the guided vane and metal filter reduced over 90% micro-dust, while sprayed water cleans the vane and filters, resultantly minimizing the maintenance budget. The preliminary evaluations of the developed design make it possible to reduce not only cheaper maintenance budget due to the characteristic water spraying but the cost of water comes from mainly rain and underground.