• Restorative Dentistry and Endodontics
• /
• v.28 no.1
• /
• pp.89-99
• /
• 2003

The purpose of this study was to investigate the bonding of resin- based root canal sealer, AH26 when the sealer was applied as a thin layer between dentine and gutta-percha surface. In this study forty non-caries extracted human molars and resin-based root canal sealer(AH 26, DeTrey/Dentsply, Germany) were used. Disks of gutta-percha, 6mm in diameter.6mm thick (Diadent/Dentsply, Korea) for thermoplastic obturation were used and dentin surfaces were treated with 2% NaOCl(Group 1) or 2%NaOCl+17% EDTA(Group 3). Disks of gutta-Percha, 6mm in diameter.6mm thick (Diadent/Dentsply, Korea) for conventional obturation were used and dentin surface were treated with 2% NaOCl(Group 2) or 2%NaOCl+17% EDTA(Group 4). Enamel was removed by a horizontal section 1mm below the deepest portion of the central occlusal groove by using a watercooled low speed diamond saw. A second horizontal section was done around cementoenamel junction. Exposed dentin surface was cut to approximately $8{\times}8{\;}mm$ rectangular shape and was ground against 320, 400, 600 grade silicon carbide abrasive paper serially. After grinding, the dentine surface were soaked in a solution of 2% NaOCl for 30 minutes and twenty of specimens were treated with 17% EDTA solution for 1 minute. The treated specimens were washed and dried, Root canal sealer, AH26 was prepared according to the manufacture's instructions The Gutta-percha and dentin surface were coated with a thin layer of the freshly mixed seal or. The specimens were left overnight at room temperature. After their initial set, they were transferred to an incubator at $37$^{\circ}C$ for 72 h. After 72 hours, resin blocks were made. The resin block was serially sectioned vertically into stick of $1{\cdot}1mm$. Twenty sticks were prepared from each group. After that, tensile bond strength f3r each stick was measured with Microtensile Tester Failure patterns of the specimens at the interface between gutta-percha and dentin were observed under the SEM(x1000) and Stereomicroscope (LEICA M42O, Meyer Inst., TX U.S.A) at 1.25 x25 magnification. The results were statistically analysed by using a One-way ANOVA and Tukey's test. The results were as follows; 1. Tensile bond strengths($mean{\pm}SD$) were expressed with ascending order as follows: Group 1, $3.09{\pm}$ 1.05Mpa : Group 2, $6.23{\pm}1.16MPa$ : Group 3, $7.12{\pm}1.07MPa$ : Group 4, $10.32{\pm}2.06MPa$. 2. Tensile bond strengths of the group 2 and 4 used disks of gutta-percha for conventional obturation were significantly higher than that of the group 1 and 3 used fir thermoplastic obturation. (p < 0.05). 3. Tensile bond strengths of the group 3 and 4 treated with 2% NaOC1+17% EDTA were significantly higher than that of the group 1 and 2 treated with 2% NaOCl. (p < 0.05). 4. In analysis of failure patterns at the interface between sealer and gutta-percha, there were observed 49 (61%)cases of adhesive failure patterns and 31 (39%) cases of mixed failures patterns.

• Journal of Mushroom
• /
• v.21 no.4
• /
• pp.254-260
• /
• 2023

The characteristics and spore production of Gonji7ho, Bunhong, and Sunjung fruiting bodies were assessed at different growth stages. The shape of the Pleurotus species fruiting body starts out short and small, then takes on a typical mushroom shape as it grows. Gonji7ho has a long stalk, Bunhong has a short stalk and a wide cap, and Sunjung's cap and stalk dimensions are intermediate. Each variety displayed deep color at the beginning of growth but became steadily lighter with continued growth. The shape of the linkage between the mushroom stalk and cap changed from an initial central position to a lateral position after the growing stage. Gonji7ho cap diameter increased 7-fold from 15.5 mm (5 days of growth) to 37.9 mm (9 days of growth). Growth rates for each growth day measured using the growth percentage of the previous day were 285.5% (5 → 6th day), 182.2% (6 → 7th day), 129.4% (7 → 8th day), and 103.8% (8 → 9th day). This trend was also observed in Bunhong and Sunjung, but Bunhong's growth rate was more rapid (4.9 fold on day 6, 2.7 fold on day 7) and continued to increase through day 9. Harvest yield, which is of greatest interest to farmers, displayed a similar trend spanning the growth period, as did cap diameter. Gonji7ho harvest yield increased rapidly until day 7 of growth (more than 177%), then growth slowed down beginning around day 8, and further decreased on day 9 (98%). Similar trends were observed in Bunhong and Sunjung. Bunhong showed characteristic rapid growth in harvest yield (4.9 fold compared to the previous day on day 6 and 2.7 fold on day 7), and the increase continued through day 9. A decrease in mushroom harvest yield commonly seen in the late growth stage is thought to be due to the death of some mushrooms and decomposition of cap tissue. Basidiospore content increased with number of growth days but decreased after day 8. Gonji7ho yielded the highest production on day 7 of growth, coinciding with harvest time, with 209,000,000 spores. This trend was also observed in Bunhong and Sunjung. These results will provide researchers with basal data and guide farmers in selecting the optimal harvest day.

• Korean Journal of Plant Resources
• /
• v.37 no.4
• /
• pp.392-400
• /
• 2024

This study was conducted to find the flowering and growth characteristics according to the different altitudes (plains and mid-mountain regions) and cultivation methods (field and plastic houses cultivation) of Elsholtzia splendens. Experimental regions located at 12 meters and 500 meters above sea level were selected for the plains and the mid-mountain, respectively, and the same method was applied for cultivation management by different altitudes and cultivation methods. In the mid-mountain region, flower bud emergence (2-3 days), flowering (9 days), and full bloom (6-7 days) stages of Elsholtzia splendens were earlier than in the plains, and field cultivation was earlier than plastic house cultivation. The plant height, the main stem diameter, and the number of branches tended to increase gradually after an initial rapid growth at 59 to 69 days after planting date. The days of duration of sunshine (less than 8 hours) from the rainy season (June 20) to the period when vegetative growth increases gradually (59 to 69 days after planting) was 22 to 29 days and 26 to 35 days in the plains and the mid-mountain regions respectively, and this period was estimated time of transition from vegetative growth to reproductive growth. The spikes growth of Elsholtzia splendens by cultivation altitudes was higher in the mid-mountain region than in the plains, and there were no statistically significant differences in growth characteristics except for the main stem diameter, the number of branches, and the dry matter. Also, the amount of flowering and growth was higher in the plastic house cultivation compared to the field cultivation. As a result, some differences in flowering amount were observed when cultivating Elsholtzia splendens for landscaping purposes, but it was considered possible to cultivate in both plains and mid-mountain regions. This study therefore provides ecological information for understanding the relationship between weather characteristics and growth of Elsholtzia splendens.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.26 no.3
• /
• pp.141-150
• /
• 2024

Garlic (Allium sativum L.) is considered as one of the most important vegetables with various uses throughout the many countries. Also, it is one of the most economically important Allium species, and has been widely cultivated for more than 5,000 years. In Korea, garlic is planted in late summer and is grown from autumn and spring of the next year. Bulb starts to form when temperature rises under longer photoperiods. Garlic growth is affected by various factors such as storage conditions, humidity, duration of minimum temperature, and photoperiod. Also, the storage conditions for propagation seed are known to potentially affect future vegetative stages. In this study, we evaluated to effect of the inter-bud growth and growth of the southern-type cultivar 'Namdo' according to storage temperatures. The inter-bud growth, emergence & sprouting rate, and initial growth of stored garlic at low temperatures (5~15℃) exhibited robust growth, while garlic stored at high temperatures (30℃) was investigated to be sluggish compared to another treatments. However, the bulb diameter of stored garlic at 10 ℃ and 15℃ increased to 148.7% and 154.0 % compared to untreated garlic, respectively. Also, the bulb weight of stored garlic increased to 285.7% and 294.4% compared to control, respectively. In contrast, garlic stored at 5℃ showed a decrease of 70 .5% in bulb dimeter and 70 .6% in bulb weight compared to the control. As a results, it was confirmed that the storage temperature of garlic affects the inter-bud growth, emergence & sprouting rate, growth, bulb diameter, and bulb weight. These results will be to the possibility that is possible to estimate the growth cycle of garlic using the growth index for the improvement of crop modeling.

• The Korean Journal of Malacology
• /
• v.29 no.4
• /
• pp.263-272
• /
• 2013

The development of swift's scallop Chlamys swiftii, reared in the laboratory, has been examined through the investigation of morphological characteristics in fertilized egg, larvae and juvenile. Eggs were fertilized with a dilute sperm solution to improve the survival of fertilized eggs. Developing larvae were maintained at a temperature of $16{\pm}0.5^{\circ}C$ and salinity concentration of 33 ppt. We have investigated the fertilization rates and egg number spawned at several stimulating conditions such as sunlight exposure, air dry, seawater temperature rise ($5^{\circ}C$) and seawater temperature rise ($5^{\circ}C$) after exposure of air dry for spawning induction of swift's scallop Chamys swiftii. Stimulation treated with sunlight exposure and seawater temperature rise ($5^{\circ}C$) have shown the spawning number of 700,000-900,000 and 700,000-800,000 per individual, respectively while stimulation treated with seawater temperature rise ($5^{\circ}C$) after exposure of air dry have shown the high spawning number of 1,000,000-1,500,000 per individual. Survival rate of D-shaped larvae of swift's scallop put into the different seawater temperatures of $8^{\circ}C$, $12^{\circ}C$, $16^{\circ}C$, $20^{\circ}C$ and $24^{\circ}C$ has been 4.1%, 11.6%, 32.7%, 18.6% and 3.2%, respectively. Fertilized eggs with the diameter of $72{\mu}m$ developed into trochophore larvae of $103{\pm}3.8{\mu}m$ shortly after 35 hours and to D larvae of $129{\pm}10.4{\mu}m$ shell length within 72 hours. It took 336 hours to become initial Umbo-stage larva of $145{\pm}16.8{\mu}m$ shell length. Post larvae, which have been $197{\pm}13.6{\mu}m$ shell length, spontaneously have settled in the attachment substances. It have required 528 hours from fertilized eggs to early attached juvenile to become initial juvenile size of $245{\pm}15.8{\mu}m$ shell length.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.2
• /
• pp.105-112
• /
• 2014

Purpose: The aim of present investigation was to find out the influence of several times iatrogenic mobilization in the initial stage of implant installation on bone-implant osteointegration. Materials and methods: The experimental implants (3.75 mm in diameter, 8.0 mm in length) were made of commercially pure (Grade IV) titanium, and were treated with RBM ($MegaGen^{(R)}$: Ca-P) on lower 4.0 mm part. Only lower part of implant was inserted to bone and the implants were nonsubmerged. The 130 implants (two in each tibia) were inserted into the monocortical tibias of 33 rabbits which each weighed more than 3.5 kg (Female, New Zealand White). According to the removal torque interval, the groups were divided into 13 groups, group I (1 day), group II (1 day + 2 days), group III (1 day + 2 days + 3 days), group IV (1 day + 2 days + 3 days + 4 days), group V (2 days), group VI (2 days + 4 days), group VII (2 days + 4 days + 6 days), group VIII (2 days + 4 days + 6 days + 8 days), group IX (4 days), group X (4 days + 7 days), group XI (4 days + 7 days + 10 days), group XII (4 days + 7 days + 10 days + 14 days) and control group. In the control group, the removal torque was measured at 8 weeks with a digital torque gauge (Mark-10, USA). In the experimental groups, the removal torque was given once, twice, three times or four times by experiment design before the final removal torque and the value was measured each time. The implants were then screwed back to their original positions. All the experimental groups were given a final healing time of 8 weeks after placement, in which values were compared with the control groups and the 1st, 2nd, 3rd or 4th removal torque values in each experimental group. Results: In comparison of the final removal torque tests among experimental groups, the removal torque value of experimental groups except group XII were not statistically different that of control group. And the values of group I and II were significantly higher than the values of group VI, VIII, X, XI, and XII. In addition, the values of group III, IV, and V were significantly higher than group XI and XII. In comparison of the removal torque in the each experimental group, the final removal torque were significantly higher in all groups except group VIII, X, XI, and XII. Conclusion: If sufficient healing time was allowed, a few mobilization of fixture at the very early stage after the implant placement in the rabbits didn't interrupt the final bone to implant osseointegration.

• Korean Journal of Organic Agriculture
• /
• v.23 no.4
• /
• pp.781-796
• /
• 2015

This study was carried out to investigate the effect of no-tillage and split irrigation on the growth of pepper plant under green house condition in Jeonnam province. Moisture content of soil at whole quantity irrigation in tillage was increased rapidly regardless of soil depth for initial irrigation and then was decreased continuously until next irrigation. Deviation of moisture content in soil was decreased with increasing depth of soil. Moisture contents of top soil and subsoil (20 cm) at whole quantity irrigation in no-tillage were increased with sunrise, and then decreased with sunset. Moisture contents of top soil in tillage, and top soil and subsoil (20 cm) in no-tillage at half quantity irrigation indicated a cyclic diurnal variation by evapotranspiration. Salinity of soil was increased after initial irrigation and then was decreased continuously until next irrigation. With increasing depth of soil, increases of salinity in soil was delayed. Salinity of top soil in no-tillage was increased between AM 11:00 and AM 12:00, and then showed the highest level between PM 2:00 and PM 6:00 on a cyclic diurnal variation by evapotranspiration. Salinity of subsoil (30 cm) in no-tillage was not measured a cyclic diurnal variation. Moisture content and salinity of soil was positive correlation regardless of tillage and no-tillage cultivation. Growth of pepper in no-tillage cultivation was higher than that in tillage cultivation. Main branch Length and stem diameter of half quantity irrigation plot was higher than that of whole quantity irrigation plot regardless of tillage and no-tillage cultivation. After harvesting, the number of pepper fruits of half quantity irrigation plot was increased remarkably by 49% and 47%, in tillage and no-tillage cultivation, respectively. Pepper yield of no-tillage cultivation plot was higher by 8% than that of tillage cultivation plot. Pepper yield of half quantity irrigation plot was increased remarkably by 36% and 39%, in tillage and no-tillage cultivation, respectively.

• Journal of Mushroom
• /
• v.16 no.3
• /
• pp.155-161
• /
• 2018

In this study, we analyze the growth environment using smart farm technology in order to develop the optimal growth model for the precision cultivation of the bottle-grown oyster mushroom 'Suhan'. Experimental farmers used $88m^2$ of bed area, 2 rows and 5 columns of shelf shape, 5 hp refrigerator, 100T of sandwich panel for insulation, 2 ultrasonic humidifiers, 12 kW of heating, and 5,000 bottles for cultivation. Data on parameters such as temperature, humidity, carbon dioxide concentration, and illumination, which directly affect mushroom growth, were collected from the environmental sensor part installed at the oyster mushroom cultivator and analyzed. It was found that the initial temperature at the time of granulation was $22^{\circ}C$ after the scraping, and the mushroom was produced and maintained at about $25^{\circ}C$ until the bottle was flipped. On fruiting body formation, mushrooms were harvested while maintaining the temperature between $13^{\circ}C$ and $15^{\circ}C$. Humidity was approximately 100% throughout the growth stage. Carbon dioxide concentration gradually increased until 3 days after the beginning of cultivation, and then increased rapidly to approximately 2,600 ppm. From the 6th day, $CO_2$ concentration was gradually decreased through ventilation and maintained at 1,000 ppm during the harvest. Light was not provided at the initial stage of oyster mushroom cultivation. On the $3^{rd}$ and $4^{th}$ day, mushrooms were irradiated by 17 lux light. Subsequently, the light intensity was increased to 115-120 lux as the growth progressed. Fruiting body characteristics of 'Suhan' cultivated in a farmhouse were as follows: Pileus diameter was 30.9 mm and thickness was 4.5 mm; stipe thickness was 11.0 mm and length was 76.0 mm; stipe and pileus hardness was 0.8 g/mm and 2.8 g/mm, respectively; L values of the stipe and pileus were 79.9 and 52.3, respectively. The fruiting body yield was 160.2 g/850 ml, and the individual weight was 12.8 g/10 unit.

• Nuclear Engineering and Technology
• /
• v.39 no.5
• /
• pp.603-616
• /
• 2007

Roy Huddle, having invented the coated particle in Harwell 1957, stated in the early 1970s that we know now everything about particles and coatings and should be going over to deal with other problems. This was on the occasion of the Dragon fuel performance information meeting London 1973: How wrong a genius be! It took until 1978 that really good particles were made in Germany, then during the Japanese HTTR production in the 1990s and finally the Chinese 2000-2001 campaign for HTR-10. Here, we present a review of history and present status. Today, good fuel is measured by different standards from the seventies: where $9*10^{-4}$ initial free heavy metal fraction was typical for early AVR carbide fuel and $3*10^{-4}$ initial free heavy metal fraction was acceptable for oxide fuel in THTR, we insist on values more than an order of magnitude below this value today. Half a percent of particle failure at the end-of-irradiation, another ancient standard, is not even acceptable today, even for the most severe accidents. While legislation and licensing has not changed, one of the reasons we insist on these improvements is the preference for passive systems rather than active controls of earlier times. After renewed HTGR interest, we are reporting about the start of new or reactivated coated particle work in several parts of the world, considering the aspects of designs/ traditional and new materials, manufacturing technologies/ quality control quality assurance, irradiation and accident performance, modeling and performance predictions, and fuel cycle aspects and spent fuel treatment. In very general terms, the coated particle should be strong, reliable, retentive, and affordable. These properties have to be quantified and will be eventually optimized for a specific application system. Results obtained so far indicate that the same particle can be used for steam cycle applications with $700-750^{\circ}C$ helium coolant gas exit, for gas turbine applications at $850-900^{\circ}C$ and for process heat/hydrogen generation applications with $950^{\circ}C$ outlet temperatures. There is a clear set of standards for modem high quality fuel in terms of low levels of heavy metal contamination, manufacture-induced particle defects during fuel body and fuel element making, irradiation/accident induced particle failures and limits on fission product release from intact particles. While gas-cooled reactor design is still open-ended with blocks for the prismatic and spherical fuel elements for the pebble-bed design, there is near worldwide agreement on high quality fuel: a $500{\mu}m$ diameter $UO_2$ kernel of 10% enrichment is surrounded by a $100{\mu}m$ thick sacrificial buffer layer to be followed by a dense inner pyrocarbon layer, a high quality silicon carbide layer of $35{\mu}m$ thickness and theoretical density and another outer pyrocarbon layer. Good performance has been demonstrated both under operational and under accident conditions, i.e. to 10% FIMA and maximum $1600^{\circ}C$ afterwards. And it is the wide-ranging demonstration experience that makes this particle superior. Recommendations are made for further work: 1. Generation of data for presently manufactured materials, e.g. SiC strength and strength distribution, PyC creep and shrinkage and many more material data sets. 2. Renewed start of irradiation and accident testing of modem coated particle fuel. 3. Analysis of existing and newly created data with a view to demonstrate satisfactory performance at burnups beyond 10% FIMA and complete fission product retention even in accidents that go beyond $1600^{\circ}C$ for a short period of time. This work should proceed at both national and international level.

• Journal of Chest Surgery
• /
• v.38 no.6 s.251
• /
• pp.403-409
• /
• 2005

Pulmonary atresia with intact ventricular septum is morphologically heterogeneous, and the surgical outcome remains suboptimal compared to other complex congenital heart defects. We evaluated the long-term results for repair of pulmonary atresia with intact ventricular septum, Material and Method: Between January 1992 and June 2004, 38 patients underwent repair of pulmonary atresia with intact ventricular septum. The average age was 18 days $(2\~382\;days)$. The average Z-value of the tricuspid annulus diameter was -3.1$(-5.6\~0.8)$. Thirteen $(36\%)$ patients had right ventricle-to-coronary artery fistulas, and $4(11\%)$ patients had right ventricle-dependent coronary circulation. Average follow-up was 55 months $(3\;months\~2.2\;years)$, Result: Twenty-four patients under-went initial right ventricle (RV) decompression and 14 patients underwent systemic-to-pulmonary arterial shunt only. The average size of the tricuspid annulus of the patients who underwent RV decompression was significantly larger than that of the patients who underwent systemic-to-pulmonary arierial shunt only (Z-value -2.2 vs. -4.8, p=0.000). There were $5(13\%)$ early and 1 late deaths. Early deaths occurred in 3 patients who had undergone RV decompression, and in 2 patients who had undergone systemic-to-pulmonary arterial shunt only (p=1.0). Biventricular repair was achieved in $12(32\%)$ patients, single ventricular repair in $8(21\%)$, and one and a half ventricular repair in $4(l1\%)$ patients. Nine $(24\%)$ patients are waiting for the definitive repair. Kaplan-Meier survival at 5 and 8 years was $83.2\%$, respectively. Conclusion: Most of the deaths occurred after the initial palliation. Overall long-term survival was satisfactory. Early mortality should be reduced with careful preoperative evaluation and proper surgical strategy.