• Corrosion Science and Technology
• /
• 제21권2호
• /
• pp.158-169
• /
• 2022

The objective of this study was to investigate the electrochemical behavior and damage degree of metal surface under different conditions by performing a potentiodynamic polarization experiment using an electropolishing solution for UNS S31603 based on initial delay time and surface roughness (parameters). A second anodic peak occurred at initial delay time of 0s and 100s. However, it was not discovered at 1000s and 3600s. This research referred to an increase in current density due to hydrogen oxidation reaction among various hypotheses for the second anodic peak. After the experiment, both critical current density and corrosion current density decreased when the initial delay time (immersion time) was longer. As a result of surface analysis, characteristics of the potentiodynamic polarization behavior were similar with roughness, although the degree of damage was clearly different. With an increase in surface roughness value, the degree of surface damage was precisely observed. As such, electrochemical properties were different according to the immersion time in the electropolishing solution. To select electropolishing conditions such as applied current density, voltage, and immersion time, 1000s for initial delay time on the potentiodynamic polarization behavior was the most appropriate in this experiment.

• 전기학회논문지
• /
• 제57권6호
• /
• pp.1022-1025
• /
• 2008

This paper presents the generation of the high voltage squarewave pulse using distributed RLC circuit. The demonstrated test was performed with the distributed RLC circuit which consists of the resistance, the inductance and the capacitance. Pspice simulation was also conducted about the experiment circuit. The result of the experiment was in good agreement with the result of the simulation. Theoretical analysis of the initial peak value at the squraewave pulse was derived from the results of the experiment and simulation. Additionally, the characteristics of the time delay was analyzed about the spherical gap switch and the surface discharge gap switch, respectively. It is concluded that the surface discharge gap switch is better than the spherical gap switch to reduce the time delay.

• 한국군사과학기술학회지
• /
• 제21권5호
• /
• pp.665-674
• /
• 2018

In this paper, we propose a development results of a D-type non-rechargeable lithium battery($Li/SOCl_2$) on improvement in a low cost protection circuit of discharge for domestic military power source. According to this study, we describe a new design and product with 8-bit microcontroller in the protection circuit which can estimate state of health of the battery regardless of occurring an initial voltage delay. Also this paper discuss and facilitate development as solution to a safety about the non-rechargeable lithium batteries. As a result, we verified a quality of the protection circuit by a development test and evaluation(DT&E) process.

• 전력전자학회논문지
• /
• 제21권4호
• /
• pp.364-372
• /
• 2016

In this paper, a voltage controller for the seamless transition of a grid-connected inverter for ESS is proposed. The single-phase inverter is operated as a current controller when the grid is connected and as a voltage controller in the stand-alone mode when the grid is disconnected. Generally, in the case of grid recovery, the overcurrent may flow into the system because of the mismatch phase between the inverter output and grid voltages. The proposed controller resolves the overcurrent problem through phase delay problems with initial value feed-forward control of the integrator when the grid voltage is restored. The effects of the control method are simulated through PSIM, and the usefulness of the control method is verified through experiments.

• 전력전자학회논문지
• /
• 제18권3호
• /
• pp.225-231
• /
• 2013

This paper presents an improved signal processing technique in the square-wave-type voltage injection method for IPMSM sensorless drives. Since the sensorless method based on the square-wave voltage injection does not use low-pass filters to get an error signal for estimating rotor position and allows the frequency of the injected voltage signal to be high, the sensorless drive system may achieve an enhanced control bandwidth and reduced acoustic noise. However, this sensorless method still requires low-pass and band-pass filters to extract the fundamental component current and the injected frequency component current from the motor current, respectively. In this paper, these filters are replaced by simple arithmetic operations so that the time delay for estimating the rotor position can be effectively reduced to only one current sampling. Hence, the proposed technique can simplify its whole signal process for the IPMSM sensorless control using the square-wave-type voltage injection. The proposed technique is verified by the experiment on the 800W IPMSM drive system.

• 대한전자공학회논문지SD
• /
• 제40권6호
• /
• pp.408-420
• /
• 2003

이 논문에서는 1) 넓은 잠금 범위를 위한 이중 루프 동작과 2) 차세대 패키지 스큐 개선에 대한 전압 발생기와 안티퓨즈 회로를 사용한 프로그래머블 레프리카 딜레이, 두 가지 이점을 갖는 Delay Lock Loop(DLL)을 기술하였다. 이중 루프 동작은 차동 내부 루프 중 하나를 선택하기 위해 외부 클럭과 내부 클럭 사이의 초기 시간차에 대한 정보를 사용한다. 이를 이용하여 더 낮은 주파수로 DLL의 잠금 범위를 증가시킨다. 덧붙여서, 전압발생기와 안티퓨즈 회로를 사용한 프로그래머블 레프리카 딜레이의 결합은 패키지 공정 후에 온-오프 칩 변화로부터 발생하는 외부 클럭과 내부 클럭 사이에 스큐 제거를 해준다. 제안된 DLL은 0.16um 공정으로 제조되었고, 2.3v의 전원 공급과 42㎒ - 400㎒의 넓은 범위에서 동작한다. 측정된 결과는 43psec p-p 지터와 400㎒에서 52㎽를 소비하는 4.71psec 실효치(rms)지터를 보여준다.

• 한국화재소방학회논문지
• /
• 제19권2호
• /
• pp.75-80
• /
• 2005

적충형 PTC 서미스터의 특성연구를 위해 $(0.90Ba+0.05Sr+0.05Ca)TiO_3+0.01TiO_3+0.01SiO_2+0.0008MnO_2+0.0018Nb_2O_5$와 같은 실험조성식을 설정한 후 표면실장(SMD) 적층형 PTC 시편을 제작하였다. 그 결과 상온 비저항 값을 크게 낮출 수 있고 용도에 따라 전류용량을 크게 할 수 있었으나 적층화로 인해 peak 비저항이 크게 낮아지고 열용량이 커짐으로써 스위칭(switching)시간이 늦어지는 점을 확인하였다. 전압-전류 특성에서는 적층수가 증가할수록 초기 최대전류값이 증가하며 큐리점에 대응하여 저항값이 급격히 커지는 전이전압(전계)도 증가함을 보였다. 그러나 인가전압(전계)을 증가시킬 경우 peak 비저항값을 높일 수 있어 스위칭시간을 줄일 수 있다 이 소자는 화재감지기의 센서로 활용될 수 있다.

• Nuclear Engineering and Technology
• /
• 제49권1호
• /
• pp.209-215
• /
• 2017

Fast neutron irradiation was used to improve the switching speed of a 600-V nonpunch-through insulated gate bipolar transistor. Fast neutron irradiation was carried out at 30-MeV energy in doses of $1{\times}10^8n/cm^2$, $1{\times}10^9n/cm^2$, $1{\times}10^{10}n/cm^2$, and $1{\times}10^{11}n/cm^2$. Electrical characteristics such as current-voltage, forward on-state voltage drop, and switching speed of the device were analyzed and compared with those prior to irradiation. The on-state voltage drop of the initial devices prior to irradiation was 2.08 V, which increased to 2.10 V, 2.20 V, 2.3 V, and 2.4 V, respectively, depending on the irradiation dose. This effect arises because of the lattice defects generated by the fast neutrons. In particular, the turnoff delay time was reduced to 92 nanoseconds, 45% of that prior to irradiation, which means there is a substantial improvement in the switching speed of the device.

• 한국태양에너지학회 논문집
• /
• 제32권spc3호
• /
• pp.255-261
• /
• 2012

Since PV PCS uses output current sensor for ac output current control, the sensor's sensing value includes unnecessary offset inevitably. If PV inverter is controlled by the included offset value, it's output current will generate DC offset. The DC offset of output current for trans-less PV inverter is fatal to grid, which results in saturating grid side transformer. Usually DSP controller of PV inverter reads several times sensing value during initial operation and, finally, it's average value is used for offset calibration. However, if temperature changes, the offset changes, too. And also, the switch device is not ideal, both each switching element of the voltage drop difference and on & off time delay difference generate DC offset. Thus, to compensate for deadtime and the switch voltage drop, feedback control by output current DC offset should be provided to compensate additional distortion of the output current. The validity of the proposed method is confirmed through PSIM simulation.

• 분석과학
• /
• 제18권6호
• /
• pp.483-490
• /
• 2005

TOF 비행시간을 이용한 에어로졸 질량분석기에서 질량분석기의 분해능은 발생하는 이온의 초기에너지와 이온이 움직이는 진행방향에 따라 달라진다. 고출력 펄스형 레이저에 의하여 에어로졸로부터 용발되어 이온화된 원소들은 다른 속도로 사방으로 퍼져 나가게 되어 분해능 저하를 초래하는데 이를 방지하기 위해서 1차 가속된 이온들을 서로 다른 에너지로 후집속하여 같은 시간에 이온센서에 도달하도록 하는 장치에 대하여 연구를 수행하였다. 후집속 전위를 $90^{\circ}$ 방향으로 진행하는 이온을 중심으로 서로 다른 방향으로 걸어 줌으로써 TOF 영역을 지나 센서로 도입되는 이온의 도착 시간이 크게 개선되었음을 알 수 있었으며, 이를 실증하기 위하여 레이저 유도 이온을 만들고 후집속 장치를 구성하여 최적의 시간지연시간 및 전압 조건을 도출하여 그 성능을 증가시켰다.