• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.55-62
• /
• 2013

An analytical procedure to determine a proper profile of the spring rail that generates intended contact pressure distribution in the flat wiper blade is introduced. The flat wiper blade is one piece blade and subjected to pressing force at a center point. In this type of blade, contact pressure distribution in the tip of rubber strip is determined by the pressing force, the initial profile of the blade before contact and bending stiffness of the blade. Experimentally obtained bending stiffness of the blade assembly is almost identical to that of the spring rail. Principle of reciprocity has been used to define the initial profile of spring rail from the deformed profile that is assumed to be identical to the windshield glass profile. The procedure has been verified experimentally by measuring the contact pressure of the blade assembled with the spring rail designed by the procedure proposed here. Measured contact pressure distributions of the blades show good agreements with intended distributions over the entire blade span. Consequently, it can be concluded that proposed procedure has relatively good accuracy in developing the spring rail for flat blade having a specific contact pressure distribution.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.139-148
• /
• 1998

Internal and external heat sources will cause to deform to machine elements in the contact joint of structure, which results in the change of contact pressure distribution different from initial assembly. Heat induced variations of contact pressure will change the static and dynamic properties such as contact stiffness, damping as well as contact heat conduction in the structure In order to design and control the intelligent machine tool operating in variant conditions more sophisticatedly, the good prediction for the changes of prescribed properties are strongly required especially in the contact elements adjacent to the rotational or linear bearing. This paper presents some computational and experimental results in regard to static and dynamic characteristics of the press-fitted bush and shaft assembly which is a model of the bearing innerrace and shaft assembly. In the condition of heat generation on the outer surface of the bush, the effects of changes in the negative clearance and the heat flux on pressure distribution and dynamic properties are investigated. Results of this study show that the edge effect of the bush and the initial clearance have effects on the transient dynamic characteristics significantly.

• 전기학회논문지
• /
• 제66권7호
• /
• pp.1066-1071
• /
• 2017

Recently high voltage impulse (HVI) technique has been extensively studied for desalting processes to control the $CaCO_3$ scale formation in industrial water practices such as power plant, boiler, and heat exchange operations. Investigation of the operational parameters for the HVI is important, however, those had not been reported yet. In this study, the effect of initial feed volume and contact time on reduction of calcium ion concentration by the HVI technique was investigated. Initial feed volumes of artificial hard water which contained 100 mg/L of $Ca^{2+}$, were set to 1, 2, and 3 L respectively. After 24hr of HVI contact with 12kV, $Ca^{2+}$ ion was reduced to 50, 29 and 19 % of their initial concentration, indicating that calcium removal increased as initial feed volume decreased. This implies the applied HVI pulse energy per unit mass of calcium is important parameter determining overall desalting efficiency. A series of extended operations of HVI up to 30 days verified the long term stability of the HVI system. The calcium ion declined to 40 mg/L after 2~3 days, and further reduction of calcium was not achieved, indicating that optimum operation time could be 2~3 days under these experimental conditions. Consequently, it was confirmed that the important operational parameter of HVI technique is initial feed volume and contact time as well as the applied voltage that was already proven in the previous study.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.162-167
• /
• 2002

An automotive wheel bearing is one of the most important components to guarantee the service life of a passenger car. The endurance life of a bearing is affected by many parameters such as material properties, heat treatment, lubrication conditions, temperature, loading conditions, bearing geometry, internal clearance and so on. In this paper, we analyze the relation between loads and deformations of wheel bearing units. On the basis of it, we calculate the endurance life of wheel bearing units and suggest a method to determine the initial contact angle to achieve a maximum endurance life with considering stress concentration.

• Geomechanics and Engineering
• /
• 제16권1호
• /
• pp.11-19
• /
• 2018

Propagation of the generalized Rayleigh waves in an elastic half-space covered by an elastic layer for different initial stress combinations and imperfect contact conditions is investigated. Three-dimensional linearized theory of elastic waves in initially stressed bodies in plane-strain state is employed, the corresponding dispersion equation is derived and an algorithm is developed for numerical solution to this equation. Numerical results on the influence of the initial stress patterns and on the influence of the contact conditions are presented and discussed. The case where the external forces are "follower forces" is considered as well. These investigations provide some theoretical foundations for the study of the near-surface waves propagating in layered mechanical systems and can be successfully used for estimation of the degree of the bonded defects between layers, fault characteristics and study of the behavior of seismic surface waves propagating under the bottom of the oceans.

• 한국자동차공학회논문집
• /
• 제25권2호
• /
• pp.133-139
• /
• 2017

The timing chain system, which is a typical power transmission technology applied to a vehicle, has been widely used by the automotive industry because it is normally designed to last a car's lifetime. However, the timing chain system may cause some problems due to the shape of the chains and the polygonal behavior on contact between the chain and the sprocket. In addition, noise and vibration caused by transmission error are the most typical problems encountered by major automotive manufacturers and they are considered as the main source of customer complaint. The initial tension of the chain-sprocket system is thought to be the main cause of transmission error, and it is regarded as the source of engine vibration and noise. The initial tension of the chain system should be controlled carefully since a low initial tension can cause twisting, which may lead to a system malfunction, while a high initial tension can reduce the service life due to a worn down contact surface. In this paper, the kinematic analysis model is generated with various initial tensions, which are controlled by changing the shape of the fixed guide with the largest contact surface with chain. The results showed that the transmission error was minimized on a particular range of initial tension, and the tendency showed that the error changed with a higher sensitivity at a lower initial tension.

• 한국소음진동공학회논문집
• /
• 제17권5호
• /
• pp.456-463
• /
• 2007

It is important to improve the initial launch conditions of golf ball at impact between golf club and ball to get a long flight distance. The flight distance is greatly influenced by the initial launch conditions such as ball speed, launch angle and back spin rate. It is also important to analyze the mechanism of ball spin to improve the initial conditions of golf ball. Back spin rate is created by the contact time and force. Previous studies showed that the contact force is determined as the resultant force of the reaction forces normal and tangential to the club face at the contact point. The normal force causes the compression and restitution of ball, and the tangential force creates the spin. Especially, the tangential force is known to take either positive or negative values as the ball rolls and slides along the club face during impact. Although the positive and negative tangential forces are known to create and reduce the back spin rate, respectively, the mechanism of ball spin creation has not yet been discussed in detail in the literature. In this paper, the influence of the contact force between golf club and ball is investigated to analyze the mechanism of impact. For this purpose, the contact force and time at impact between golf club head and ball are computed using FEM and compared with previous results. In addition, we investigate the impact phenomenon between golf club head and ball by FEM and clarify the mechanism of ball spin creation accurately, particularly focusing on the effect of negative tangential force on ball spin rate.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.1017-1022
• /
• 2007

It is important to improve the initial launch conditions of golf ball at impact between golf club and ball to get a long flight distance. The flight distance is greatly influenced by the initial launch conditions such as ball speed, launch angle and back spin rate. It is also important to analyze the mechanism of ball spin to improve the initial conditions of golf ball. Back spin rate is created by the contact time and force. Previous studies showed that the contact force is determined as the resultant force of the reaction forces normal and tangential to the club face at the contact point. The normal force causes the compression and restitution of ball, and the tangential force creates the spin. Especially, the tangential force is known to take either positive or negative values as the ball rolls and slides along the club face during impact. Although the positive and negative tangential forces are known to create and reduce the back spin rate, respectively, the mechanism of ball spin creation has not yet been discussed in detail in the literature. In this paper, the influence of the contact force between golf club and ball is investigated to analyze the mechanism of impact. For this purpose, the contact force and time at impact between golf club head and ball are computed using FEM and compared with previous results. In addition, we investigate the impact phenomenon between golf club head and ball by FEM and clarify the mechanism of ball spin creation accurately, particularly focusing on the effect of negative tangential force on ball spin rate.

• 항공우주기술
• /
• 제11권2호
• /
• pp.33-38
• /
• 2012

지구 저궤도 위성은 발사체에서 분리된 이후 탑재 소프트웨어에 의해 자동으로 초기 동작을 수행한다. 이후 본체 초기 점검 기간 동안의 지상국 접속을 통해 정상 운용 모드로의 전환을 준비한다. 먼저 태양 전지판 전개 여부를 포함한 위성의 건강 상태를 확인한 이후 각 장치의 기능을 점검한다. 정상 운용 모드에 사용되는 모든 장치의 활성화가 완료된 이후 영상 촬영을 위한 기동 성능을 점검하며, 궤도 조정을 위한 기능을 점검한다. 초기 기능 점검은 한정된 지상국 교신 시간동안 수행되므로 사전에 모든 절차가 상세히 설계되어야 한다. 초기 점검 절차는 지상국 접속 시간에 따라 구분되어 수행된다. 또한 발생 가능한 모든 상황을 대비한 절차도 준비되어야 한다. 정상적인 점검 절차 수행 중에 발생할 수 있는 다양한 상황 및 예상치 못한 긴급 상황에 대한 조치 절차도 준비되어야 한다. 이러한 긴급 절차도 지상국 교신 시간을 고려해 설계된다. 저궤도 위성은 성공적으로 발사되었으며, 본체 초기 점검도 성공적으로 완료되었다. 이 논문에서는 저궤도 위성의 본체 초기 점검 설계 및 수행 결과에 대해 설명한다.

• Steel and Composite Structures
• /
• 제52권6호
• /
• pp.609-620
• /
• 2024

The impact problem of imperfect beams is crucial in engineering fields such as water conservancy and transportation. In this paper, the low velocity impact of graphene reinforced metal foam beams with geometric defects is studied for the first time. Firstly, an improved Hertz contact theory is adopted to construct an accurate model of the contact force during the impact process, while establishing the initial conditions of the system. Subsequently, the classical theory was used to model the defective beam, and the motion equation was derived using Hamilton's principle. Then, the Galerkin method is applied to discretize the equation, and the Runge Kutta method is used for numerical analysis to obtain the dynamic response curve. Finally, convergence validation and comparison with existing literature are conducted. In addition, a detailed analysis was conducted on the sensitivity of various parameters, including graphene sheet (GPL) distribution pattern and mass fraction, porosity distribution type and coefficient, geometric dimensions of the beam, damping, prestress, and initial geometric defects of the beam. The results revealed a strong inhibitory effect of initial geometric defects on the impact response of beams.