• The Journal of Korean Physical Therapy
• /
• v.31 no.6
• /
• pp.333-338
• /
• 2019

Purpose: Although previous studies on the screw-home movement (SHM) for autopsy specimen and walking of living persons conducted, the possibility of acquiring SHM based on inertial measurement units received little attention. This study aimed to investigate the possibility of measuring SHM for the non-weighted bearing using a micro-electro-mechanical system-based wearable motion capture system (MEMSS). Methods: MEMSS and camera-based motion analysis systems were used to obtain kinematic data of the knee joint. The knee joint moved from the flexion position to a fully extended position and then back to the start point. The coefficient of multiple correlation and the difference in the range of motion were used to assess the waveform similarity in the movement measured by two measurement systems. Results: The waveform similarity in the sagittal plane was excellent and the in the transverse plane was good. Significant differences were found in the sagittal plane between the two systems (p<0.05). However, there was no significant difference in the transverse plane between the two systems (p>0.05). Conclusion: The SHM during the passive motion without muscle contraction in the non-weighted bearing appeared in the entire range. We thought that the MEMSS could be easily applied to the acquisition of biomechanical data on the knee related to physical therapy.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.13 no.2
• /
• pp.247-258
• /
• 2003

In this paper, we present a pen-shaped input device equipped with accelerometers and gyroscopes that measure inertial movements when a user writes on 2 or 3 dimensional space with the pen. The measurements from gyroscope are integrated once to find the attitude of the system and are used to compensate gravitational effect in the accelerations. Further, the compensated accelerations are integrated twice to yield the position of the system, whose basic concept stems from the field of inertial navigation. However, the accuracy of the position measurement significantly deteriorates with time due to the integrations involved in recovering the handwriting trajectory This problem is common in the inertial navigation system and is usually solved by the periodic or aperiodic calibration of the system with external reference sources or other information in the filed of inertial navigation. In the presented paper, the calibration of the position or velocity is performed on-line and off-line. In the on-line calibration stage, the complementary filter technique is used, where a Kalman filter plays an important role. In the off-line calibration stage, the constant component of the resultant navigational error of the system is removed using the velocity information and motion detection algorithm. The effectiveness and feasibility of the presented system is shown through the experimental results.

• Journal of the Korea Society of Computer and Information
• /
• v.21 no.3
• /
• pp.83-89
• /
• 2016

Internet of Things (IoT) is widely used for biomechanics in sports activities and AHRS(Attitude and Heading Reference System) is a more cost effective solution than conventional high-grade IMUs (Inertial Measurement Units) that only integrate gyroscopes. In this paper, we attach the AHRS to the snowboard to measure the motion data like Air To Fakie, Caballerial and Free Style. In order to reduce the measurement error, we have adopted the sensors equipped with Kalman filtering and also used Euler angle to quaternion conversion to reduce the Gimbal-lock effect. We have tested and evaluated the accuracy and execution time of the pattern recognition algorithms like PCA, ICA, LDA, SVM to show the recognition possibility of it on the basic motions of Snowboarding from the 9-axis trajectory information which is gathered from AHRS sensor. With the result, PCA, ICA have low accuracy, but SVM have good accuracy to use for recognition of basic motions of Snowboarding.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.47-54
• /
• 2013

In this paper, we present an inertial sensor-based motion capturing system to measure and analyze whole body movements. This system implements a wireless AHRS(attitude heading reference system) we developed using a combination of rate gyroscope, accelerometer and magnetometer sensor signals. Several AHRS modules mounted on segments of the patient's body provide the quaternions representing the patient segments's orientation in space. We performed 3D motion capture using the quaternion data calculated. And a method is also proposed for calculating three-dimensional inter-segment joint angle which is an important bio-mechanical measure for a variety of applications related to rehabilitation. To evaluate the performance of our AHRS module, the Vicon motion capture system, which offers millimeter resolution of 3D spatial displacements and orientations, is used as a reference. The evaluation resulted in a RMSE of 2.56 degree. The results suggest that our system will provide an in-depth insight into the effectiveness, appropriate level of care, and feedback of the rehabilitation process by performing real-time limbs or gait analysis during the post-stroke recovery process.

• Korean Journal of Applied Biomechanics
• /
• v.30 no.3
• /
• pp.205-215
• /
• 2020

Objective: The purpose of this study was to investigate the relative angles and cross-correlation between body segments and ski among four alpine ski turning techniques. Method: 19 alpine ski instructors participated in this study. Each skier asked to perform 4- types of turning technique, classified by radius and level. 8 inertial measurement units were used to measure orientation angle of segment and ski on the anteroposterior and vertical axis. Results: Significant differences were found between types of turning in the segments-ski relative angle on the anteroposterior and vertical axis (p<.05). Although, cross-correlation showed a high correlation between angles of segment and ski, there were significant differences between types of turning. Conclusion: Based on our results, the relative movement and timing between each segment and ski is different according to the turning techniques, so the training methods should be applied differently.

• Journal of the Korea Convergence Society
• /
• v.11 no.4
• /
• pp.343-350
• /
• 2020

This study was intended to use the Inertia Sensor Units(IMU) for the national women's handball team to quantify movements for a total of 16 domestic or international practice games over five months and to identify the efficiency of training and differences in movements by position. A total of 15 players were participated excluding goalkeepers. The results are as follows. Player Load came in order of Wing>Back>Pivot and high in international games. Change of Direction(CoD) were found to have the most Pivot at low intensity, while middle and high intensity were the most in the Back. There have been a lot of low and middle intensity CoD in International games. Low-intensity acceleration(ACC) and deceleration(DEC) were found to have the most Pivot, while middle & high intensity ACC and DEC had the most Back. There have been many low and middle intensity ACC and low, middle and high intensity DEC in international games. There were many middle and high intensity jumps in Back and Wing, but there were no differences in the types of games.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.6
• /
• pp.481-487
• /
• 2013

In GPS(Global Positioning System)/INS(Inertial Navigation System) integrated navigation systems, GPS antennas and an inertial measurement units are usually installed outside and inside of the vehicle, respectively. By the difference of installed locations, performance of GPS/INS integrated navigation systems is affected by lever arm errors. For more accurate navigation, lever arm errors need to be compensated correctly since it directly affects the accuracy of navigation states. This paper proposes an effective lever arm error compensation method that utilizes velocity measurements of GPS and INS. By an experiment, feasibility of the proposed algorithm is verified. It is also shown that lever arm compensation is especially important when vehicles are experiencing rotational movements.

• Journal of Positioning, Navigation, and Timing
• /
• v.7 no.2
• /
• pp.91-103
• /
• 2018

Conventional inertial measurement units cannot be used in the spinning vehicle with high rotation rate due to gyro's narrow operation range. By the way, angular acceleration can be measured using the accelerometer array distributed in the vehicle. This paper derives a mechanization for the gyro-free INS in the navigation frame, and proposes a gyro-free INS algorithm based on the derived mechanization. In addition, the proposed algorithm is used to estimate angular velocity, attitude, velocity, and position of a spinning vehicle with high rotation rate. A MATLAB-based software platform is configured in order to show validation of the proposed algorithm. The reference trajectory of a spinning vehicle at 3 round per second, 30 round per second are set up, and the outputs of accelerometer are generated when triads of accelerometer are located at the origin and all the axes. Navigation results of the proposed algorithm for the generated output are presented. The results show that the proposed navigation algorithm can be applied to the spinning vehicle with high rotation rate.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.18 no.4
• /
• pp.405-414
• /
• 2000

A new generation of commercial satellites like IKONOS, SPOT-5 and OrbView-3,4 will have improved features, especially an higher geometric resolution with a better dynamic radiometric range. In addition high precision orbital position and attitude data will be provided by the on-board GPS receivers, IMU(Inertial Measurement Units) and star trackers. This additional information allows for reducing the number of ground control points. Furthermore this information enables direct georeferencing of imagery without ground control points. In our work mathematical models for calculating the satellite orbital parameters of SPOT-3 and KOMPSAT-1 were developed and can be easily extended to process images from other high resolution imaging systems as they become available.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.6
• /
• pp.782-788
• /
• 2018

This paper proposes a novel method for the omnidirectional camera-based image rendering synchronization system using head mounted display. There are two main processes in the proposed system. The first one is rendering 360-degree images which are remotely photographed to head mounted display. This method is based on transmission control protocol/internet protocol(TCP/IP), and the sequential images are rapidly captured and transmitted to the server using TCP/IP protocol with the byte array data format. Then, the server collects the byte array data, and make them into images. Finally, the observer can see them while wearing head mounted display. The second process is displaying the specific region by detecting the user's head rotation. After extracting the user's head Euler angles from head mounted display's inertial measurement units sensor, the proposed system display the region based on these angles. In the experimental results, rendering the original image at the same resolution in a given network environment causes loss of frame rate, and rendering at the same frame rate results in loss of resolution. Therefore, it is necessary to select optimal parameters considering environmental requirements.