• 한국산업보건학회지
• /
• 제20권3호
• /
• pp.175-183
• /
• 2010

Windows are widely used for natural ventilation of the various buildings. Especially high level windows as a part of industrial ventilation systems, play a crucial role in natural ventilation. Compared to mechanical ventilation system, natural ventilation has the advantage of lower installation and operating costs. In general, high level windows for industrial buildings have three types; louver type, 45$^{\circ}$ open type and 90$^{\circ}$ open type. Based on previous studies, it was found that the louver type and 45$^{\circ}$ open type are very effective in reducing rainwater penetration, but they did not have enough ventilation efficiencies. Preliminary tests were performed with the various types of windows. It was found that a 90$^{\circ}$ open double layer type window was the best among those which tested in our preliminary tests. Simulated rain was used to estimate the amount of rain penetrated through windows and to observe the paths of rain penetration. Various 90$^{\circ}$ open windows were tested to find the windows with minimum rain penetration and maximum ventilation efficiency.

• 한국환경과학회지
• /
• 제20권5호
• /
• pp.581-587
• /
• 2011

Industrial natural ventilation systems consist of gravity ventilator, the high/low windows and doors. Especially, the high windows play an important role in the industrial natural ventilation systems. Generally speaking, industrial high windows are divided into 3 types; louver type, $45^{\circ}$ open type and $90^{\circ}$ open type. This study was numerically and experimentally conducted. Three types of windows were tested to know the ventilation characteristics and estimate the ventilation efficiencies. Numerically, computational fluid dynamics software (AIR PAK Ver. 2.0) was used to observe the flow characteristics inside the industrial building and the concentration contours generated by the tracer gas method. Experimentally, the flow visualization technique and the tracer gas method were applied with the model building to characterize the flow pattern inside the model building and to estimate the ventilation efficiencies with the different windows. It was found that $90^{\circ}$ open type window was most effective for the discharge of pollutants from the industrial building. On the other hand, the louver type window was found to be less effective than any other windows.

• 한국환경과학회지
• /
• 제5권6호
• /
• pp.683-697
• /
• 1996

Industrial ventilation is a crucial engineering measure to protect workers from hazardous airborne contaminants. Designing a ventilation system is not an easy task. To solve this problem, many U. S. computer programs and softwares have been developed. In Korea, asoftware, called as VPMC, was developed by Korea Industrial Safety Corporation. But VPMC could not stand alone since it can be used to design not a hood, but a ventilation system. In this research, therefore, a preprocessing software was developed. It can be used to design general ventilation system, canopy hood, open surface tank hood. The program was written in Microsoft Visual Basic. In near future, this software will be incorporated into a total package software which can be used to design a whole ventilation system.

• 한국산학기술학회논문지
• /
• 제14권5호
• /
• pp.2086-2091
• /
• 2013

산업환기의 근본 목적은 유해물질로부터 작업자의 건강을 지키는 것으로, 제품생산과정에서 발생하는 유해물질 등을 빠른 시간에 외부로 배출하여 공기의 질을 높이고자 한다. 최근 산업환기에 대한 인식이 생산중심에서 인간중심으로 변하면서 이에 대한 중요성이 증가하고 있다. 본 연구에서는 아연말 코팅 룸에서 발생하는 악취제거를 목적으로 코팅 룸 내부의 공기유동에 대한 전산 시뮬레이션을 수행하였다. 3차원 CAD 프로그램인 SolidWorks를 이용하여 코팅 룸 전체와 배기시스템을 모델링하였으며 Flow Simulation 프로그램을 이용하여 오염물 발생 부위 중심으로 배기성능을 분석하였다. 또한 국소배기 장치를 이용하여 코팅 룸 내부 공기의 흐름 방향과 공기의 유속을 개선하였다.

• 한국안전학회지
• /
• 제27권5호
• /
• pp.196-202
• /
• 2012

An industrial safety helmet primarily intended to protect the wearer's head. It is to prevent or reduce the danger due to flying or dropping objects, falling and prevent the danger due to an electric shock given to the head. However, thermal discomfort of the head is one of the main complaints in the case of wearing safety helmet. Ventilation holes are not allowed in safety helmets on domestic regulations except for industrial safety helmets which are to protect wearer's head against flying or dropping objects. This paper is to produce the need for enlargement of allowing on ventilation holes' regulation to class B. This study reviewed foreign standards' regulations on ventilation holes of safety helmets. Some standards recommend that ventilation may be improved when fresh air is able to enter the helmet around its lower edge and to exit via holes in the helmet located in the upper one third of the helmet. And in the experiments, relationships of ventilation holes and the temperature over the head are analyzed. The experimental results show that the cooling effect of ventilation holes in the upper one third of the helmet is meaningful.

• 한국산업융합학회 논문집
• /
• 제20권1호
• /
• pp.8-18
• /
• 2017

This research analyzed the ventilation effect of the multi-span greenhouse based on the types of greenhouse structure, weather conditions, and locations inside the greenhouse. To compare and analyze the ventilation effects with different types of greenhouse, the uniform environmental conditions should be selected in advance. But these factors are not controlled and require tense many precision facilities and labor forces. Thus, the CFD simulation was used for the air stream to be analyzed qualitatively and quantitatively. In addition, for the ventilation effect analysis, the TGD (Tracer Gas Decay) was used to overcome the shortcomings of the current ventilation measurement method. The calculation error of ventilation rate using TGD was low (10.5%). Thus, the TGD is very effective in calculating the ventilation efficiency. The wind direction of 90 degrees showed the best ventilation effect. The ventilation rate also decreased along the air circulation path, and the rate was the lowest around the outlet. The computed fluid method (CFD) turned out to be a power tool for simulating flow behavior in greenhouse.

• 한국산업보건학회지
• /
• 제7권1호
• /
• pp.133-151
• /
• 1997

Industrial ventilation is one of crucial engineering measures to protect workers from hazardous airborne contaminants. Designing a ventilation system is not an easy task. To solve this problem, U.S. computer programs and softwares have been developed. In Korea, a software, called as VPMC(Velocity Pressure Method Calculation), was developed by Korean Industrial Safety Corporation. Since VPMC is a DOS-based software, it could not be a user-friendly one. In this study, a Windows-based software was thus developed to overcome the difficulty in using a software for designing the ventilation system. As far as we know, this kind of Windows-based software is the first in the world. But this software should be kept being revised. The future work would include introduction of GUI(Graphic User Interface) and enhancement of editing functions by using Data-Base programs.

• 설비공학논문집
• /
• 제24권3호
• /
• pp.240-246
• /
• 2012

The supply and use of exhaust heat recovery ventilation system as effective energy saving equipment has been increasing steadily. The exhaust heat recovery ventilation system can be installed at ceiling of balcony or emergency space. However, ventilation system can not be installed at emergency space because where have to remain as empty space by law. Therefore, the proper installation space of ventilation system is needed. In this study, to install heat recovery ventilation system in the light weight wall, thickness of heat exchanger was assembled below 140 mm. One or two paper heat exchangers were installed in the ventilation system. The efficiency of heat recovery was analyzed through performance experiment on case of cooling and heating mode.

• 한국산업보건학회지
• /
• 제3권1호
• /
• pp.91-98
• /
• 1993

This study was carried out to investigate characteristic of vinyl chloride emissioned from poly vinyl chloride extrusion process and to evaluate the efficiency of local exhaust ventilation system. Before local ventilation facility was constructed in poly vinyl chloride extrusion process, the average worker exposure to vinyl chloride was 3.15 ppm, which exceeded Threshold Limit Value of American Conference of Gorvernmental Industrial Hygienists (ACGIH-TLV), 1 ppm. lt is possible that vinyl chloride residues in the poly vinyl chloride resin was released or degased due to extrusion heat. The larger the width of vinyl tube become, the higher worker exposure to vinyl chloride was. It is estimated that vinyl chloride from vinyl chloride resin increased as amount of poly vinyl chloride resin extruded in the extrusion process increased. Canopy hood was an appropriate type for poly vinyl chloride resin extrusion process. This local exhaust ventilation has fan static pressure of 7.65 inch wg($190mmH_2O$, total volumetric flowlate of 4,796 CFM ($135.8m^3$/min) and fan power requirement of 12 hp (8.952 Kw). After this local exhaust ventilation was constructed there, the average concentration of worker exposure to vinyl chloride was reduced to be 0.46 ppm, which was below the Threshold Limit Value, 1 ppm. Also, the removal efficiency rate of vinyl chloride attained by local exhaust ventilation was 85.3%. It was a statistically significant (p<0.01).

• 한국산업보건학회지
• /
• 제19권2호
• /
• pp.113-126
• /
• 2009

In the recent years, health effect of dimethylformamide(DMF) has been one of critical industrial hygiene issues. There might be many factors to increase the exposure level of DMF. Among those factors, industrial ventilation would be one of the main factors. In this study, industrial ventilation systems of printing processes in synthetic leather factories were thoroughly surveyed and the improved ventilation systems were proposed. 7 synthetic leather factories were selected for this study. After the ventilation systems were visually inspected, each component of the system was tested by using the appropriate instruments. Hood face velocities, fan exhaust flow rates, fan static pressures, fan rotation rates, etc were measured. In addition, flow visualization techniques were used to observe flow patten around hoods and inside the factory buildings. After gathering all qualitative and quantitative information, the test results were analysed to see if any improvement might be necessary. For the system to be improved, the re-design plans were made by using computational fluid dynamics softwares. The softwares used in this study were AIRPAK and STAR-CD. The effectiveness of the several improvement options were tested, then the best cost effective option was selected. Finally, the standard ventilation systems were proposed to minimize the exposure levels of DMF.