• Proceedings of the KAIS Fall Conference
• /
• 2011.12a
• /
• pp.269-272
• /
• 2011

주물 사업장의 용해 공정인 장입과 출탕 작업, 첨가제 투입 과정에서 많은 분진이 발생한다. 실제 주물 사업장에서 사용되는 후드 형태는 매우 다양하며 구조적인 문제점으로 인해 효과적인 배기가 어려운 실정이다. 본 연구를 통해 실제 사업장에 전기로의 다양한 공정 형태에 대한 대응이 가장 우수한 직인식 후드 방식을 제시하고, 전산유체역학(CFD : Computational Fluid Dynamics)을 이용한 오염물질 거동 예측 기법을 활용하여 직인식 후드의 적정 배기량을 산정하여 현장에 제시하였다. 실제 현장에서는 본 개념 설계 결과를 바탕으로 용해 공정에 $400m^3/min$의 배기량을 갖는 직인식 후드를 설치한 결과, 매우 만족스러운 분진 제어 효율을 확인할 수 있었다.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.20 no.1
• /
• pp.63-69
• /
• 2010

This study was conducted to compare the concentration of various air contaminants in nine different laboratories during routine activities. Volatile organic compounds (VOC) were sampled and analyzed using NIOSH Method 1500 and asbestos fibers were sampled and analyzed using NIOSH Method 9002 and 7400. Detectable levels of acetone, toluene and ethanol were found in all the laboratories and xylene and n-hexane were detected in eight of the nine laboratories. All the VOC concentrations were well below the Korean Ministry of Labor's Exposure Limit and American Conference of Governmental Industrial Hygienists' (ACGIH) Threshold Limit Values (TLVs). Total VOC concentrations at the university laboratories were significantly higher than those at governmental agency laboratories. Airborne fiber concentrations were below 0.01 fibers/cc, while the concentration of chrysotile was 2% in insulation materials sprayed on the ceiling of one laboratory. While all the governmental agency laboratories (n=4) had fume hoods, two out of the five university laboratories did not have fume hoods. The capture velocity of half of the fume hoods were below the maintenance standard(0.4 m/sec). In conclusion, the study suggests that the current controls in place at both university and government agency laboratories are not sufficient in limiting exposure to harmful chemicals to non-detectable levels, though they appear to be adequate in protecting workers to levels below applicable occupational exposure limits. The study also suggests that researchers working in university laboratories may be exposed to greater levels of contaminant than those working in government agency laboratories.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.310-320
• /
• 2020

BTS has established itself as a leading Korean popular music group in the global mainstream music market. In addition, BTS's fashion style is receiving so much attention that it is featured in the social networks of foreign media and the public. The purpose of this study considers BTS' fashion trends based on the analysis of their fashion styles. The methods and scope of this study have been combined with theoretical studies related to the fashion impact of BTS and BTS, as well as content analysis studies based on the image of BTS over the last five years. The results of this study are as follows. First, it was found that they pursue classic and modern styles through suits that emphasize straight silhouettes, the use of achromatic colors, and simplified decorations. Second, it has been shown that BTS prefers a casual style of free-spirited and comfortable sensibility by matching a jacket with a round shoulder line, toned-down skinny jeans, hood T-shirts, lettering patterns, and vivid colors. Third, BTS pursues a dynamic and active sporty style by utilizing the sleeveless basketball shirts, round neckline baseball shirts and shorts, training pants, and overfit sweatshirts with an emphasis on lettering patterns.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.2
• /
• pp.83-90
• /
• 2011

It has been very important to have an exact evaluation for risk factors in order to prevent WMSDs(Work-related Musculoskeletal Disorders). However, most WMSDs evaluation methods have always been some problems of possibilities associated with subjective evaluation. Therefore, this study tried to conduct a sort of usability analysis on three major evaluation methods(OWAS, RULA, REBA). Specifically, major subjects in the study consisted of three parts as follows; comparison of the results between experienced and inexperienced observers, analysis for the consistency of the results in terms of different evaluation times, and analysis for the consistency of the results in terms of different job characteristics(based on the part of the automobile). The results of the study were summarized as follows; 1) There was statistically significant difference of the results by RULA and by REBA between experienced and inexperienced observers. This might be due to the fact that experienced observers have had better ability to detect the important working posture during evaluation. However, the results by OWAS did not give any significantly different results between experienced and inexperienced observers, 2) All three checklists applied by experienced subjects did not show any single result significantly different in terms of different evaluation times. This might have to do with high intra-observer reliability from some of previous studies, 3) The five parts of an automobile were selected as five major jobs with different job characteristics in the automobile industry. Specifically, they were door part, front part(hood, etc.), inside part(dash board, seats, etc.), rear part(trunk etc.), and bottom part. All three methods did not show any significant differences for the results from each observers. Further study on this subject would eventually provide a sophisticated evaluating guidelines for WMSDs regarding determination of observer-specific evaluation, identification of repetitive number of evaluations for stable results for each checklist, determination of job-specific evaluation methods, and so on.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.506-512
• /
• 2018

The fine dust generated in the home and restaurant business occupies a low ratio of about 4% of the total fine dust emissions. However, at the foodservice business, the rate of change of the pollutant concentration is very high, so that the temporary fine dust concentration can be measured up to 60 times. The pollutants generated from non-industrial combustion plants consist of particulate fine dust and gaseous organic compounds. To remove these pollutants, cleaning dust collection system, which is an effective system for simultaneous removal of gaseous and particulate matter, is applied. This is a method of increasing the probability of diffusion capture of the Brownian motion by pressurized liquid injection method using the atomizing nozzle. The dust removal efficiency of the fine dust collecting system was analyzed by nozzle spraying air pressure condition and angle using the manufactured fine dust removing system. As a result, it was confirmed that the efficiency of removal of fine dust and gaseous organic compounds was more than 90%. The developed system is expected to be highly usable in the future because it can remove particulate dust from the existing plant hood system without any installation cost.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.11 no.1
• /
• pp.1-8
• /
• 2001

This study was performed to evaluate a local exhaust ventilation system capability and welding fume concentration in welding laboratory at 5 technical high schools. Results of the study are as follows; 1. The personal exposure of welding fume in welding laboratory was measured. The geometric mean of 73 personal samples was $6.27mg/m^3$($3.85{\sim}9.88mg/m^3$), and 68.5% of these exceeded TLV of the Korea Ministry of Labor. 2. The geometric mean of welding fume at outside of booth was $2.27mg/m^3$($1.57{\sim}2.58mg/m^3$). All of measured concentrations were lower than TLV of the Korea Ministry of Labor. 3. Local exhaust ventilation system in welding laboratory could not remove hazardous substance effectively because of inappropriate canopy hood and absurd design. 4. The possibility of exposure risk was estimated to be high because of working point under breathing zone, misplacement of working table and insufficient supply of respiratory protector. 5. The mean values of capture velocity and transportation velocity of local exhaust ventilation system in welding laboratory were 0.38m/sec, 4.27m/sec respectively. These values were satisfied the guideline of the Korea Ministry of Labor. 6. The efficiency of performance of local ventilation system was anticipated to be decreased because of accumulated dust and alien substance on fan and duct.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.22 no.2
• /
• pp.167-180
• /
• 2020

The purpose of this study is to present the use of traditional culture and the direction of various fashion designs by developing and producing contemporary fashion designs on the Muslim costumes of the Chinese Hui minority. Based on research methods, the cultural background was investigated and the design characteristics were summarized. Based on the results of this survey, 4 sets of women's fashion were designed. The design intent was to feature Muslim traditional costumes and to adopt a functional contemporary design. The conclusions of this study are as follows. First, simple and indecisive clothing shows the innocent and good side of the congregation. In this study, traditional dresses were used to make use of the simple silhouette and color, and to create a contemporary atmosphere, various materials, such as wool, glossy industrial complex, lace, and fur were used to create a modern sense design by adding diversity to the simple silhouette. Second, the biggest feature of the regimented Muslim costume focuses on a head cover and suggests a contemporary sense of hood improvement, and a design that can be used with two sides. These hooded head covers can provide fashion and diversity and can be proposed as functional. Third, contemporary Muslim fashion is gaining global attention and it is possible to develop various fashion designs based on traditional motifs. This study was able to increase the feminine image by changing the solemnity of the communal dress without discarding the foundation of the traditional religious culture based on the daily dress of the people.

• Elastomers and Composites
• /
• v.52 no.1
• /
• pp.35-47
• /
• 2017

A comprehensive survey of the available literature showed that in the last few decades, there has been a growing interest in the use of thermoplastic vulcanizates (TPVs). TPVs are the second largest group of soft thermoplastic elastomers (TPEs) after styrene-based block copolymers, and offer a wide range of potential and proven applications, including in mechanical rubber goods, under-the-hood applications in the automotive field, industrial hose applications, electrical applications, consumer goods, and soft touch applications. Over the last two decades, TPVs have shown a strong and steady market growth (~12% per year). Commercialized TPVs are commonly based on blends of ethylene propylene diene monomer (EPDM) rubber and polypropylene (PP), and to a lesser extent on combinations of butyl or nitrile rubber with PP. EPDM/PP TPVs are characterized by finely dispersed crosslinked EPDM rubber particles (particles size varying between 0.5 and $2.0{\mu}m$) distributed in a continuous thermoplastic PP matrix. If the rubber particles of such a blend are small enough and if they are vulcanized well enough, then the properties of the blend are generally improved. This review article introduces various topics and aspects relevant to EPDM/PP TPVs. The development of TPVs, the use of various types of crosslinking systems and co-agents as crosslinking agents for PP/EPDM blends, the morphology and rheology of TPVs, and their typical end-use applications are also reviewed.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.15 no.3
• /
• pp.166-175
• /
• 2005

Health effects associated with metal working fluid (MWF) exposures include dermatitis, respiratory disease, hypersensitive pneumonitis, and asthma. Frequently, occupational exposures to MWFs are controlled by ventilating an enclosure with an air cleaning unit that includes a fan preceded by various kinds of filtration. There are several kinds of air cleaning units used in machining centers. But the associated troubles have hindered from efficiently using these devices. The main problem is the relatively short period of filter replacement. The reason is that the air cleaning units usually do not have the de-oiling systems, thus leading the earlier clogging of filters and reducing the flow rate of hood. Thus, the first stage of study was conducted to overcome this problem by developing the new oil mist collector equipped with the easy de-oiling system. The principle of de-oiling is that the centrifugal force generated by spinning the drum covered by filter fabric separates oils from the filter fabric. It would be very similar to the spin-dry laundry. By adopting this de-oiling technique, the problems associated with the conventional oil mist collectors could be solved. Several tests/analyses were performed to make the lab-scale oil mist collector. The collection efficiencies and the de-oiling efficiencies of commercially available filter fabrics were tested. Subsequently, the endurance test were conducted by observing SEM photos of filter fabrics and measuring tensile strength/expansion coefficient after spinning the filter drum for 20 minutes at the different rotation speeds. By doing these experiments, the most appropriate filter fabric and rotation speed/duration were selected. Finally, the new oil mist collector was designed. In the near future, this device must be tested in the real machining center.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.17 no.2
• /
• pp.120-130
• /
• 2007

A oxygen generating closed-circuit SCBA for escape from fire will be newly developed and then a program for estimating service time for it should be required. A SCBA made on an experimental basis consisted of five components such as half facepiece (mask), $KO_2$ box, oxygen reservoir, $CO_2$ remover and hood. The half mask had a good fitting performance since fit factors for 10 subjects were all above 100. It was found that height of subjects should be the best variable to estimate service time. Measured service time was inversely correlated with height of subjects. Service life time could be estimated by interpolation and extrapolation using inverse relationship between height and measured service time, for example, 28 minutes for male and female of 170 cm during resting, 10 minutes at the walk of 4 km/h and 5 minutes at the walk of 6 km/h considering safety margin of 20%. The study implies that program for estimating service time for the SCBA should require subject's height, speed of walk (4 km/h and 6 km/h) and fit testing. Considering safety margin, selecting younger subjects would be better. The study on the number of subjects and selecting facial dimensions should be more needed for the final program.