• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.93-99
• /
• 2019

The purpose of this study was to investigate the bond strength between PEKK(Polyetherketoneketone) and Sinfony(3M ESPE, Seefeld, Germany) the dental composite resin by proposing the three representative surface treatment methods and evaluate to see if they affect the bond strength between two materials. A total of 30 PEKK($Pekkton^{(R)}$ Ivory, $Cendres+M{\acute{e}}taux$, Bienne, Switzerland) specimens were prepared, embedded in acrylic resin, polished(P 1200 grid) to surface, and each group was divided into 10 specimens. After then, by the surface treatment method, it classified into three groups(n=10) such as Air abrasion group(PN), applying Single Bond Universal(3M ESPE) after Air abrasion(PB), applying OPAQUE(3M ESPE) after Air abrasion(PO). Then, veneering was performed by using Sinfony(3M ESPE, Seefeld, Germany). All completed specimens were allowed to rest in a $37^{\circ}C$ water bath for 24 hours. Shear bond strength of each group was measured and fracture patterns were classified. Statistic analysis was performed with One-way ANOVA followed by post hoc Scheffe tast (p<.05). Statistical analysis was performed using the SPSSWIN 21.0 program. As a result of one-way ANOVA, the average value of PB group was $27.67{\pm}4,18MPa$ and it was shown as the highest bond strength, PN and PO were $20.43{\pm}1.70$ and $19.8{\pm}4.77MPa$ each, and these were relatively low(F=18.4, P<.001), and as the post-test the Scheffe test was conducted and verified (p<.05). After examining the scheffe test, it was showed significant differences as PB>PO, PB>PN(p<.001). Through this study, in order to enhance the bonding force between PEKK and the composite resin, perform the Air abrasion and surface treatment by using Single Bond Universal(3M ESPE) is recommended, and as coMPared with other studies. And it is assumed that the increase of the application time of the Air abrasion affects the increase of the shear bond strength. Thus, further research is required.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.288-296
• /
• 2019

Radiation cooling has used ceilings or floors as cooling surfaces. In such cases, to avoid moisture condensation on the surface, the surface temperature needs be higher than the dew point temperature or an additional dehumidifier is added. In this study, with a goal for residential application, intentional moisture condensation on the cooling surface was attempted, which increased the cooling capacity and improved the indoor comfortness. This method included two separate refrigeration cycles - convection-type dehumidifying cycle and the panel cooling cycle. Test results on the panel cooling cycle showed that, at the standard outdoor ($35^{\circ}C/24^{\circ}C$) and indoor ($27^{\circ}C/19.5^{\circ}C$) condition, the refrigerant flow rate was 8.8 kg/h, condensation temperature was $51^{\circ}C$, evaporation temperature was $8.8^{\circ}C$, cooling capacity was 376 W and COP was 1.75. Furthermore, the panel temperature was uniform within $1^{\circ}C$ (between $13^{\circ}C$ and $14^{\circ}C$). As the relative humidity decreased, the cooling capacity decreased. However, the power consumption remained approximately constant. In the convection-type dehumidification cycle, the refrigerant flow rate was 21.1 kg/h, condensation temperature was $61^{\circ}C$, evaporation temperature was $5.0^{\circ}C$, cooling capacity was 949 W and COP was 2.11 at the standard air condition. When both the radiation panel cooling and the dehumidification cycle operated simultaneously, the cooling capacity of the radiation panel cycle was 333 W and that of the dehumidification cycle was 894 W, and the COP was 1.89. As the fan flow rate decreased, both the cooling capacity of the radiation panel and the dehumidification cycle decreased, with that of the dehumidification cycle decreasing at a higher rate. Finally, a possible control logic depending on the change of the cooling load was proposed based on the results of the present study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.1
• /
• pp.376-383
• /
• 2019

This study was conducted to investigate academic self-efficacy, critical thinking disposition, and learning motivation, which influence problem solving ability in nursing students. Data were collected from June 4, 2018 to June 29, 2018, and the final 213 data points were used for analysis. The SPSS/WIN 22.0 program was used to conduct descriptive statics, Pearson's correlation coefficient, t-tests, ANOVA, Scheffe's test and multiple regression analysis. The problem solving ability according to the general characteristics differed among residential type (F=3.930, p=0.021) and satisfaction with major (F=4.618, p=0.011). In the correlation between academic self-efficacy, critical thinking disposition, learning motivation, and problem solving ability of the subject, academic self-efficacy (r=0.573, p<0.001), critical thinking disposition (r=0.620, p<0.001), and learning motivation (r=0.563, p<0.001). The factors affecting the problem solving ability of the study subjects were major satisfaction (${\beta}=.117$, p=0.036), academic self-efficacy (${\beta}=0.314$, p<0.001), critical thinking disposition (${\beta}=0.318$, p<0.001), and learning motivation (${\beta}=0.217$, p=0.004), with an explanatory power of 45.2%. In this study, it is necessary to confirm the effects of the development of the intervention program and the application of the program, which can improve the problem solving ability of nursing students.

• Korean Journal of Microbiology
• /
• v.54 no.4
• /
• pp.384-397
• /
• 2018

The aim of this study is to screen the strains of Bacillus spp. possessing safety, probiotic activity, and so on, which can be utilized as probiotic resource for using the feed and supplement food of companion animal. About 300 isolates were isolated from traditional Korean sauces, four isolates that did not have or produce the six kinds of B. cereus type vomiting and diarrhea toxin genes, ${\beta}$-hemolytic, and three kinds of carcinogenic enzymes were selected. Antibiotic gene retention, cell surface hydrophobicity, antibiotic sensitivity, and glucose utilization were analyzed for four isolates, and finally SRCM 100731 was selected. SRCM 100731 was named as Bacillus amyloliquefaciens SRCM 100731 16S rRNA sequencing analysis, and carried out optimization of cell growth for industrial applications such as pet food and feed. The effects of 14 different components on cell growth were investigated and three significant positive factors, molasses, sodium chloride, and potassium chloride were selected as the main factors based on a Plackett-Burman design. In order to find out optimal concentration on each constituent, we carried out central composite design. The predicted optimized concentrations were 7% molasses, 1.1% sodium chloride, 0.5% potassium chloride. Finally, an overall about 7-fold increase in dry cell weight yield ($12.6625{\pm}0.0658g/L$) was achieved using the optimized medium compared with the non-optimized medium ($1.8273{\pm}0.0214g/L$). This research is expected to be highly utilized in the growing pet industry by establishing optimal cultivation conditions for industrial application as well as screening Bacillus amyloliquefaciens SRCM 100731 as probiotic resource for companion animal.

• Food Engineering Progress
• /
• v.21 no.4
• /
• pp.360-366
• /
• 2017

Fish skin peptide-loaded liposomes were prepared in 100 mL and 1 L solution as lab scales, and 10 L solution as a prototype scale. The particle size and zeta potential were measured to determine the optimal conditions for the production of fish skin peptide-loaded liposome. The liposome was manufactured by the following conditions: (1) primary homogenization at 4,000 rpm, 8,000 rpm, and 12,000 rpm for 3 minutes; (2) secondary homogenization at 40 watt (W), 60 W, and 80 W for 3 minutes. From this experimental design, the optimal conditions of homogenization were selected as 4,000 rpm and 60 W. For the next step, fish peptides were prepared as the concentrations of 3, 6, and 12% at the optimum manufacturing conditions of liposome and stored at $4^{\circ}C$. Particle size, polydispersion index (pdI), and zeta potential of peptide-loaded liposome were measured for its stability. Particle size increased significantly as manufacture scale and peptide concentration increased, and decreased over storage time. The zeta potential results increased as storage time increased at 10 L scale. In addition, 12% peptide showed the formation of a sediment layer after 3 weeks, and 6% peptide was considered to be the most suitable for industrial application.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_3
• /
• pp.1817-1826
• /
• 2022

After the hydrogen fluoride leak in Gumi in 2012, the government has been systemizing the disaster management system, such as responding to and managing chemical accidents. In particular, the Ministry of the Interior and Safety (MOIS) is in charge of evacuation of residents following chemical accidents based on the Framework Act on Management of Disaster and Safety. In this study, an application plan was presented to support and utilize the decision-making support for evacuation of residents after a chemical accident using the chemical accident investigation equipment of the National Disaster Management Research Institute (NDMI). In the equipment operation system for scientific information collection due to chemical accidents, the roles and purpose of use of long/short distance measurement equipment were presented according to regular and emergency situations. Using the data acquired through long/short distance measurement equipment, it can be used as basic data for resident evacuation decision-making by monitoring whether chemicals are detected in an emergency and managing data on detected substances by company in a regular situation. As a result of measuring chemical substances in order to verify on-site usability by equipment only for the regular operation system, it was confirmed that real-time detection of chemical substances is possible with long distance measuring equipment. In addition, it was confirmed that it was necessary to check the measurable distance and range of the equipment in the future. In the case of short distance measurement equipment, hydrocarbon-based substances were mainly detected, and it was confirmed that it was measured at a higher level in Ulsan-Mipo National Industrial Complex than in Onsan National Industrial Complex. It is expected that it can be used as basic data to support decision-making in the event of chemical accidents through continuous data construction in the future.

• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.334-346
• /
• 2022

There is a lack of knowledge and information on the understanding and application of the Process Safety Management (PSM) system, recognized as a major cause of industrial accidents in small-and medium-sized workplaces. Hence, it is necessary to prepare a protocol to secure the practical and continuous levels of implementation for PSM and eliminate human errors through tracking management. However, insufficient research has been conducted on this. Therefore, this study investigated and analyzed the various violations in the administrative measures, based on the regulations announced by the Ministry of Employment and Labor, in approximately 200 small-and medium-sized PSM workplaces with fewer than 300 employees across in korea. This study intended to contribute to the prevention of major industrial accidents by developing a facility maintenance web program that removed human errors in small-and medium-sized workplaces. The major results are summarized as follows. First, It accessed the web via a QR code on a smart device to check the equipment's specification search function, cause of failure, and photos for the convenience of accessing the program, which made it possible to make requests for the it inspection and maintenance in real time. Second, it linked the identification of the targets to be changed, risk assessment, worker training, and pre-operation inspection with the program, which allowed the administrator to track all the procedures from start to finish. Third, it made it possible to predict the life of the equipment and verify its reliability based on the data accumulated through the registration of the pictures for improvements, repairs, time required, cost, etc. after the work was completed. It is suggested that these research results will be helpful in the practical and systematic operation of small-and medium-sized PSM workplaces. In addition, it can be utilized in a useful manner for the development and dissemination of a facility maintenance web program when establishing future smart factories in small-and medium-sized PSM workplaces under the direction of the government.

• Composites Research
• /
• v.36 no.1
• /
• pp.1-15
• /
• 2023

Demand for energy consumption reduction is increasing according to the development expectations of future mobility. Lightweight structural materials are known as a method to reduce greenhouse gas emissions and improve energy efficiency. In particular, fiber reinforced polymer composite (FRP) is attracting attention as a material that can replace existing metal alloys due to its excellent mechanical properties and light weight. In this paper, industrial applications and research trends of carbon fiber reinforced composites (CFRP, carbon FRP) and self-reinforced composites (SRC) were reviewed based on the reinforcement, polymer matrix, and manufacturing process. In order to overcome the expensive process cost and long manufacturing time of the epoxy resin-based autoclave method, which is mainly used in the aircraft field, mass production of CFRP-applied electric vehicles has been reported using a high-pressure resin transfer molding process including fast-curing epoxy. In addition, thermoplastic resin-based CFRP and interface enhancement methods to solve the recycling issue of carbon fiber composites were reviewed in terms of materials and processes. To form a perfect matrix-reinforcement interface, which is known as the major factor inducing the excellent mechanical properties of FRP, studies on SRC impregnated with the same matrix in polymer fibers have been reported. The physical and mechanical properties of SRC based on various thermoplastic polymers were reviewed in terms of polymer orientation and composite structure. In addition, a copolymer matrix strategy for extending the processing window of highly drawn polypropylene fiber-based SRC was discussed. The application of CFRP and SRC as lightweight structural materials can provide potential options for improving the energy efficiency of future mobility.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.19 no.2
• /
• pp.45-61
• /
• 2024

This study looked in-depth at the importance of cultivating and manifesting entrepreneurship, which is emphasized for companies to gain a competitive advantage and promote innovation in the uncertain environment that organizations face and in the development of technology due to recent industrial advancement, the following innovative performance, and the mechanisms in the performance process. Entrepreneurship is emphasized as a key factor in inducing creative work performance, creation and application of new ideas, and innovative performance at various levels within the organization in various global companies. In particular, this study examined the influence of the CEO's cultivation and expression of entrepreneurship as an organizational leader on the innovative behavior of organizational members, which is a leading factor in the organization's innovative performance, and the role of creative self-efficacy as a mechanism. Through this, the study was to verify the importance of creativity and cultivating a sense of self-efficacy for demonstrating innovative performance within an organization. Additionally, it was to confirm the role of organizational commitment of organizational members as a situational factor. For the empirical analysis, a total of 247 office workers were surveyed, sampled from 10 venture companies engaged in the manufacturing industry in industrial complexes in Daejeon, Korea. As the result of empirical analysis showed, it was confirmed that each sub-factor of the CEO's entrepreneurship had a positive effect on the innovative behavior of organizational members. And in the process, the importance of the creative self-efficacy of members to demonstrate innovative performance was verified by confirming positively significant mediating effect of creative self-efficacy. Furthermore, in the case of organizational commitment, it was found that the innovativeness and proactiveness of the CEO strengthened the positive influence on the creative efficacy of the organization members. Based on the results of empirical analysis, theoretical and practical implications were provided to improve the importance of cultivating and manifesting the CEO's entrepreneurship to demonstrate innovation within the organization.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.239-248
• /
• 2011

This paper evaluated types and characteristics of development projects occurred in coastal area (Public Water) by analyzing an application status of Sea Area Utilization Conference System that effective protect and manage marine environment and ecosystem from various artificial utilization and development enforced in 2008. Also, system improvement for stable settlement and security of efficiency considering exposed problems during system enforcement were diagnosed. The number of Sea Area Utilization Conference (SAUC) performanced during the period of 2009-2010 was 3,705, which consisted of simple SAUC (87.0%), general SAUC (12.8%), and Sea Area Utilization Impact Assessment (SAUIC; 0.2%). The general SAUC was accomplished for Public Water reclamation (43.4%), seawater supply and drainage (17.5%), dredging sediment (5.5%), installation of port facilities (4.6%) and fishing harbor facilities (2.3%), and others (23.4%). Statements of Environmental Impact Assessment (EIA) were reviewed mainly for construction of port facilities (32.9%), followed by construction of industrial complex, development of tourism and leisure complex, road construction, and development of energy facilities. It would be necessary to strengthen effectiveness of the system, advertisement, and capability of conference and review agency, and to enhance confidence of marine EIA continuously, according to the increase of development projects, and diversity and enlargement of development types.