• 한국재료학회지
• /
• 제13권11호
• /
• pp.721-724
• /
• 2003

A Fe-Si-B-Ni amorphous alloy manufactured by one roll melt-spinning method showed the crystallization temperature difference of a maximum $10^{\circ}C$ according to each lot. This temperature difference had a considerable influence on the annealing process to be conducted for obtaining the proper inductance of the alloy. The proper annealing temperature of the alloy was $480^{\circ}C$ and the annealing time increased as the crystallization temperature increased. The activation energy measured by Kissinger method increased as the crystallization temperature increased. Therefore, the annealing process must be adjusted by the crystallization temperature difference of the amorphous alloy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.745-746
• /
• 2006

The purpose of this paper is to discuss the reasons creating the difference between inductances calculated and measured in the interior permanent magnet synchronous motor designed for the traction. Moreover, the method applied to estimate the inductance is introduced in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1416_1417
• /
• 2009

This paper shows the characteristic of wave tail according to inductance values in 10/$350{\mu}s$ impulse circuit with crowbar switch. The PSpice was used to simulate the 10/$350{\mu}s$ current waveform and lightning current impulse generator was used to generate real current waveform. As a capacitor of condenser bank increases, a virtual front time increases and a time to half-value decreases. To get a perfect 10/$350{\mu}s$ current waveform, we should consider the combination of circuit values of the inductance, capacitance, time difference between trigger pulses and charged voltage of capacitor bank.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1150-1152
• /
• 2005

This paper deals with inductance profile of linear switched reluctance motor. Inductance profile of LSRM calculate at align and unalign position using magnetic equivalent circuit method. Magnetic equivalent circuit method of this paper used method of reference[3],[4], but this method used modification on account difference of design specification Also, analysis result compares with data that is derived through an experiment, and proved validity.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 A
• /
• pp.171-173
• /
• 2000

This paper presents a discriminating algorithm between magnetizing inrush and internal faults of transformers using difference of a differential current. Incase of inrush, change of magnetizing inductance repeats. Thus, second difference of differential current periodically shows pulse while periodic pulse is not represented in case of internal winding fault. The proposed algorithm is suitable irrespective of the amount of remanent flux.

• 한국정보전자통신기술학회논문지
• /
• 제15권5호
• /
• pp.315-320
• /
• 2022

일반적인 나선형 인덕터의 경우에 비대칭 구조를 가짐에 따라 포트의 방향에 영향을 받게 된다. 본 논문에서는 2층이면서 대칭 구조를 가질 수 있는 나선형 인덕터를 제안하고 시뮬레이션 및 주파수 특성을 분석하였다. 기존 단층 대칭형 인덕터가 3.9~4.2nH의 인덕턴스를 갖는 것과 비교하여 제안된 2층 대칭 나선형 인덕터는 포트에 변함없이 0.3~1.2GHz 범위에서 11~12nH의 인덕턴스, 800MHz에서 약 4.4의 품질계수, 약 2.7~2.8GHz의 자기공진주파수를 가진다. 이는 기존 일반적인 나선형 인덕터가 포트에 따라 큰 차이를 갖는 것과 비교하여 포트의 방향에 대한 영향이 적은 것을 확인할 수 있었다.

• Journal of Electrical Engineering and Technology
• /
• 제1권3호
• /
• pp.308-312
• /
• 2006

The inductance difference between conducting layers of high-Tc superconducting (HTSC) power transmission cable causes the current sharing of each conducting layer to be unequal, which decreases the current transmission capacity of HTSC power cable. Therefore, the design for even current sharing in HTSC power transmission cable is required. In this paper, we investigated the current distribution of HTSC power cable with a shield layer dependent on the pitch length and the winding direction of each layer. To analyze the effect of the shield layer on the current sharing of the conducting layers of HTSC power cable, the current distribution of HTSC power cable without a shield layer was compared with the case of HTSC power cable with a shield layer. It could be found through the analysis from the computer simulations that the shield layer of HTSC power cable could be contributed to the improvement of current distribution of conducting layers at the specific pitch length and the winding direction of conducting layer. The result and discussion for the current distribution calculated for HTSC power transmission cable with a shield layer were presented and compared with the cable without a shield layer.

• 한국초전도ㆍ저온공학회논문지
• /
• 제5권1호
• /
• pp.35-39
• /
• 2003

A typical HTS power transmission cable has multi-layer conductor structure to increase the current capacity. The tapes of the innermost layer are wound on a round former, and adjacent tapes of another layer are separated by a thin insulating film. However, usually the current is not evenly distributed among the layers because of inductance difference of each layer, and the inductance is provided by the winding pitch of each layer's tape. Consequently n method to make the current distribution more uniform is a adjusting the tape winding pitch, hence reduce the AC loss. This paper describes a current distribution by adjusting a tape winding pitch of each layer. Also, this paper shows recommendations for future cable conductor prototypes.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권10호
• /
• pp.602-609
• /
• 2004

This paper presents electro-magnetic characteristics of an Interior type Permanent Magnet Synchronous Motor (IPMSM) for traction applications. The importance of instantaneous electric propulsion capability for high torque has been highlighted in the present study and thus parametric analysis is performed by Finite Element Method (FEM). The paper provides analytical & experimental results, which demonstrate a performance of the studied traction motor The goal of this paper is to present a maximum power performance for traction motor which works extension of its own rated power. Experimental results meet well with FEM analysis of traction motor owing to inductance difference.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.139.4-139
• /
• 2001

The thesis propose the sensorless vector control method that estimates the rotor speed using stator current. The estimated speed is used as feedback in a vector control system. The conventional MRAS structure has a problem the error output is decreasing as estimated speed error is increasing and the estimation performance is not robust when mutual inductance has been changed. In the proposed method, error output is proportional to estimated speed error. The described technique is less complex, robust to variations of mutual inductance. This new method can achieve much wider bandwidth speed control than that of the conventional MRAS structure.