• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.12 s.354
• /
• pp.75-82
• /
• 2006

In this paper, we design the meander line inductors with high sensitivity and high quality factor(Q) using high characteristic impedance of aperture ground plate. Sensitivity as a frequency is new defined by variation of effective inductance per analysis frequency range instead of self resonance frequency (SRF). An equivalent lumped circuit is derived to explain the characteristic of high frequency inductor. The 4 nH meander line inductor with aperture ground plate has 0.45 nH/GHz of good sensitivity and 86 of Q at 0.7 GHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.10
• /
• pp.17-23
• /
• 2003

In this study, microscale, high-performance, solenoid-type RF chip inductors were investigated. The size of the RF chip inductors fabricated in this work was 1.0${\times}$0.5${\times}$0.5㎣. The materials (96% Al2O3) and shape (I-type) of the core were determined by a Maxwell three-dimensional field simulator to maximize the performance of the inductors. The copper (Cu) wire with 40${\mu}{\textrm}{m}$ diameter was used as the coils. High frequency characteristics of the inductance (L), quality-factor (Q), and capacitance (C) of developed inductors were measured using an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). The inductors developed have inductances of 11 to 39 nH and quality factors of 28 to 50 over the frequency ranges of 250MHz to 1 GHz, and show results comparable to those measured for the inductors prepared by CoilCraf $t^{Tm}$ that is one of the best chip inductor company in the world. The simulated data predicted the high-frequency data of the L, Q, and C of the inductors developed well.l.

• Journal of the Korean Magnetics Society
• /
• v.15 no.1
• /
• pp.30-36
• /
• 2005

Recently, It has been reported that the spin sprayed ferite film shows better magnetic properties at high frequeny that the ferrite by co-firing over $800^{\circ}C$ . Besides, there is no limitation to select the substrate materials because it can be processed with relatively low temperature below $100^{\circ}C$. Therefore, we fabricated film inductor as a passive device for DC-DC converter by a use of spin sprayed embedded form was completed by via hole process of pad opening. Saturation magnetization of 0.61 T and real part of permeability of 110 were obtained in Ni-Zn ferrite. In addition, inductance of 1.52 ${\mu}H$, quality factor of 24.3 at 5 MHz were measured with spiral 16 turn inductor. The rated current of inductor was 863 mA.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.5
• /
• pp.8-15
• /
• 2002

We optimally designed the VCO(voltage-controlled oscillator) with spiral inductor using the MOSIS HP 0.5${\mu}{\textrm}{m}$ CMOS process. With the developed SPICE model of spiral inductor, the quality factor of spiral inductor was maximized at the operating frequency by varying the layout parameters, e.g., metal width, number of turns, radius, space of the metal lines. For the operation frequency of 2㎓, the inductance of about 3nH, and the MOSIS HP 0.5 CMOS process with the metal thickness of 0.8${\mu}{\textrm}{m}$, oxide thickness of 3${\mu}{\textrm}{m}$, the optimal width of metal lines is about 20${\mu}{\textrm}{m}$ for the maximum Quality factor. With the optimized spiral inductor, the VCO with LC tuning tank was designed, fabricated and measured. The measurements were peformed on-wafer using the HP8593E spectrum analyzer. The oscillation frequency was about 1.610Hz, the frequency variation of 250MHz(15%) with control voltage of 0V - 2V, and the phase noise of -108.4㏈c(@600KHz) from output spectrum.

• Journal of Korean Society of Transportation
• /
• v.23 no.5 s.83
• /
• pp.123-134
• /
• 2005

This research aims at developing a new method which can replace the existing method. known as the quality factor(Q factor) method by an L-R-C test for use in the performance test of inductive loop detectors(ILD) being installed and maintained. In this study, a sensor to detect a magnetic field in terms of frequency and intensity, a method to collect field data, the method of analysis, and the method of diagnosis were developed. An automatic diagnosis system which was developed to overcome those drawbacks has the following features : First, field data is collected automatically by a test vehicle equipped with magnetic field sensors that is running can be said to along the roadway and. thus, the new system completely overcome the roadway and, thus, the new system can be said to completely overcome the inefficiency of the existing method second, since the magnetic fold generated from the ILD is the final output of the whole system of ILD, the existing problem has been solved. third. since each of the detection area by height is collected by the magnetic sensors installed by height. a basic for the identification of the vehicle types to be detectable and the setting of adjustment factors has been made. For the automatic diagnosis system developed during in this study, a reliability test was carried out by comparing vehicle times of ILD installed ideally.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.5
• /
• pp.366-372
• /
• 2017

In this paper, the analysis of baluns that are inevitably required to design a differential low noise amplifier, The balun converts a single signal input from the antenna into a differential signal, which serves as an input to the differential amplifier. In addition, it protects the circuit from ESD(Electrostatic Discharge) coming through the antenna and helps with input matching. However, in the case of a passive balun used in general, since the AC signal is transmitted through electromagnetic coupling formed between two metal lines, it not only has loss without gain but also has the greatest influence on the total noise figure of the receiving end. Therefore, the design of a balun in a low-noise amplifier is very important, and it is important to design a balun in consideration of line width, line spacing, winding, radius, and layout symmetry that are necessary. In this paper, the factors to be considered for improving the quality factor of balun are summarized, and the tendency of variation of resistance, inductance, and capacitance of the balun according to design element change is analyzed. Based on the analysis results, it is proved that the design of input balun allows the design of low noise, high gain differential amplifier with gain of 24 dB and noise figure of 2.51 dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5B
• /
• pp.985-991
• /
• 2000

In this paper, the optimum structure of 2GHz magnetic thin film planar inductor were designed and fabricated to reduce the inductor area and to maximize the inductance L and quality factor Q of the inductor. The optimum design was performed utilizing Co90Fe10 layer multilayered with SiO2 layers to avoid the eddy-current skin effect and considering new lumped element model. New magnetic thin film inductors operating at 2GHz were fabricated on a Si substrate utilizing photo-lithography and lift-off techniques. The frequency characteristics of L, Q, and impedance in more than fifty identical inductors were measured using an RF Impedance Analyzer(HP4291B with HP16193A test fixture). The self-resonant frequencies(SRF) of the inductors were measured by a Vector Network Analyzer(HP8510). The developed inductors have SRF of 1.8 to 2.3GHz, L of 47 to 68nH, and Q of 70 to 80 near 1GHz. Finally, high frequency, high performance, planar micro-inductor(area=30.8 x 30.8il$^2$) with maximized L and Q were fabricated succefully.

• Journal of the Korean Magnetics Society
• /
• v.11 no.5
• /
• pp.222-225
• /
• 2001

The planar type inductors have a good potential for the application of miniaturized low power DC-DC converters. For those high quality application, the reduction of coil loss and also magnetic films which have good high frequency properties are required. Fabricated inductor was consisted of FeTaN/Ti magnetic film and electroplated Cu coil thickness of 100$\mu\textrm{m}$ and $SiO_2$ as a insulating layer. The inductor was designed double rectangular spiral shape for magnetic field highly confining within the device. The measured value of inductance and resistance were 980 nH and 1.7 $\Omega$ at 1 MHz as operating frequency of device. The Q factor is 3.55 at 1 MHz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.174-180
• /
• 2020

This paper presents the development of a tacho generator that is applicable to a DC motor for anti-aircraft weapon systems. In general, devices such as tacho generators and resolvers are used as feedback devices for controlling DC motors. A tacho generator with a wide operating temperature range was developed, which has robust characteristics against shock loads and vibrations according to the operational characteristics of anti-aircraft weapon systems. The target specifications were set based on the requirements of the tacho generator currently in operation. A rotor coupled to the shaft of the motor and a stator coupled to the housing of the motor were then designed and manufactured. The inductance was 31.0 mH, the terminal resistance was 147.7 ohms, and the rotational measurement factor was satisfactory under both normal operation and operating conditions after the maximum speed for the standard of 9.500 ± 0.475 V/krpm. In addition, the environmental suitability of the applied equipment was confirmed through the rate of change in unit temperature, and it was found that the temperature characteristics were all within 0.03 %/℃.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.2
• /
• pp.61-67
• /
• 2018

Welding preheating means that the surface of the base material to which the metal is welded before the main welding is heated to a constant temperature. It prevents the cracks of the adjacent influences such as reduction of material hardening degree by controlling the cooling rate, suppression of segregation of impurities, prevention of thermal deformation, and moisture removal. For this reason, it is a necessary operation for high quality welding. Induction heating is an efficient heating method that converts electric energy into heat energy by applying electromagnetic induction phenomenon. Compared with combustion heat generated by gas and liquid, it is clean, stable, and economical as well as rapid heating. It can be heated regardless of the shape, depth and material of the heating body by modifying the shape of the frequency and the coil with a simple structure. In this paper, we implemented a low frequency welding preheating system using induction heating technique and observed the temperature changes of coil resistance, inductance and automotive transmission parts according to the height of each transmission in winding coil for three kinds of automotive transmission parts. We confirmed that the change of current is a very important factor in the low frequency heating.