• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.7
• /
• pp.563-568
• /
• 2012

Indium tin oxide (ITO) films were prepared using radio frequency (RF) magnetron sputtering method, magnets were equipped near the target in the sputter to bring the plasma near the target. The effect of magnetic field that brings the plasma near the substrate was compared with that of substrate heating. The effect of substrate heating on the grain size of the ITO thin film was larger than that of the magnetic field. However, the grain size of the ITO thin film was larger when the magnetic field was applied near the substrate during the sputtering process than when the substrate was not heated and the magnetic field was not applied. If stronger magnetic field is applied near the substrate during sputtering, it can be expected that the ITO thin film with good electrical conductivity and high transparency is obtained at low substrate temperature. When magnetic field of 90 Gauss was applied near the substrate during sputtering, the mobility of the ITO thin film increased from 15.2 $cm^2/V.s$ to 23.3 $cm^2/V.s$, whereas the sheet resistivity decreased from 7.68 ${\Omega}{\cdot}cm$ to 5.11 ${\Omega}{\cdot}cm$.

• Journal of Environmental Science International
• /
• v.14 no.8
• /
• pp.801-810
• /
• 2005

The phosphor and ITO(Indium Tin Oxide) films for video phone tube (VPT) were simply prepared by the screen printing and thermal transfer methods. The increasing order of thermal firing of acrylic binder for phosphor and ITO was M6003 < M6664 < A/A 1919 < M500l < M670 1 and all mass of binders were perfectly decomposed at lower temperature than $400^{\circ}C.$ After thermal firing of phosphor paste, the residual of binder on the surface of phosphor could not be found by SEM. Aerosil as thickner provides the thixotropy property for phosphor paste but decrease the brightness of phosphor screen as residual after thermal firing. Since the thixotropy of M5001 binder without aerosil was shown and the storage modulus of phosphor paste by increasing the angular frequency was not nearly changed and the decrease of the storage modulus of phosphor paste by increasing the strain was remarkably shown. It was possible to prepare the phosphor paste which was predominant in the plate separation and the reproduction of pattern after the screen printing. Since the addition of dispersing agent to improve the printing process decreases the electrical conductivity and light transmission of ITa film, it could be found to be necessary the development of binder for phosphor paste that decreases the amount of dispersing agent possibly and does not use the aerosil as additive.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.11C no.3
• /
• pp.70-74
• /
• 2001

Admittance or impedance spectroscopy is one of the powerful tools to study dielectric relaxation and loss processes in organic and inorganic materials. In this study, the frequency dependent properties of an indium tin oxide/tris(8-hydroxyquinoline) aluminum($Alq_3$)/aluminum structure have been studied. The conductance of the $Alq_3$ film increases with the DC applied voltage up to 4V and decreases above 4V in the low frequency region. This indicates that the resistance of the device decreases with the applied bias due to the carrier injection enhancement, thereafter the injected carriers form the space charge and the additional injection of carriers is prevented. The Cole-Cole plot of the admittance takes a one-semicircle shape, which means that the device can be modeled as a parallel resistor-capacitor network. The resistance and capacitance were estimated as 8.62k${\Omega}$ and 2.7nF, respectively, at 3V in the low frequency region. The dielectric constant ( ${\epsilon}'$ ) of the $Alq_3$ film is independent of the frequency in the low frequency region below 100kHz, while the frequency dependency was observed at above 100kHz. The dielectric loss factor ( ${\epsilon}"$ ) of the $Alq_3$ film shows the dielectric dispersion below 100kHz and dielectric absorption in higher frequency domain. The dispersion is thought to be related to the hopping process of the carriers. The ${\epsilon}"$ is proportional to the reciprocal of the frequency. The dielectric relaxation time was extracted to about 0.318${\mu}s$ from the dielectric absorption spectrum.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.10
• /
• pp.817-821
• /
• 2011

We have proposed an optical thin film and micro lens to improve the luminance of organic light emitting device. The first method, optical thin film was calculated refractive index of dielectric layer material that was modulated refractive index of organic material, ITO (indium tin oxide)and glass. The second method, microlens was applied with lenses on the organic device. Optical thin films were designed with Macleod Simulator and Micro Lenses were calculated by FDTD (finite-difference time-domain) solution. The structure of thin film was designed in organic material/ITO/dielectric layer/glass. The lenses size, height and distance were 5 ${\mu}m$, 1 ${\mu}m$, 1 ${\mu}m$, respectively. The material of micro lenses used silicon dioxide. Result, The highest luminance of OLED which applied with microlens was 11,185 $cd/m^2$, when approval voltage was 14.5 V, applied thin film was 5,857 $cd/m^2$. The device efficiency applying microlens increased 3 times than the device which does not apply microlens.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.1
• /
• pp.44-49
• /
• 2014

We were investigated by cyclic voltammetry to the stability through the electrochemical characteristics of phospholipid(L-${\alpha}$-phosphatidylethanolamine, LAPE) monolayer LB films. LAPE monolayer LB films was deposited by the LB method on the indium tin oxide(ITO) glass. The electrochemical properties was measured by cyclic voltammetry with a three-electrode system in 0.5 N, 1.0 N, 1.5 N and 2.0 N $KClO_4$ solution. The measuring range is continuously oxidized to 1650 mV, with an initial potential of -1350 mV was reduced. Scanning rates of 50, 100, 150, 200, and 250 mV/s was set. As a result, LB monolayer films of LAPE was appeared on irreversible processes by the oxidation current from the cyclic voltammogram. Diffusion coefficient (D) of LAPE was calculated 195, 15.9, 5.75, 1.38 and $0.754cm^2s^{-1}{\times}10^{-9}$ at 0.01 N, 0.05 N, 0.10 N, 0.15 N and 0.20 N $KClO_4$ solutions, respectively.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.3
• /
• pp.359-366
• /
• 2014

We investigated an electrochemical properties for Langmuir-Blodgett (LB) films of saturated fatty acid and phospholipid(L-${\alpha}$-dimyristoylphosphatidyl choline, DMPC) mixture. LB films of saturated fatty acid and DMPC monolayer were deposited by the LB method on the indium tin oxide(ITO) glass. The electrochemical properties measured by cyclic voltammetry with three-electrode system(an Ag/AgCl reference electrode, a platinum wire counter electrode and LB film-coated ITO working electrode) in $NaClO_4$ solution. As a result, monolayer LB films of saturated fatty acid and phospholipid mixture was appeared on irreversible process caused by the oxidation current from the cyclic voltammogram. Diffusion coefficient (D) of saturated fatty acid and DMPC mixture(molar ratio 1:1, C12, C14, C16, C18) was calculated $1.2{\times}10^{-3}$, $2.1{\times}10^{-3}$, $1.4{\times}10^{-4}$ and $1.1{\times}10^{-3}cm^2/s$ in 0.05 N $NaClO_4$ solution, respectively.

• Journal of the Korean Chemical Society
• /
• v.50 no.1
• /
• pp.32-36
• /
• 2006

films of gold nanoparticles were formed on indium tin oxide (ITO) by an electrodeposition method from an aminosilicate stabilized gold colloid solution. The thin films were examined by cyclic voltammetry (CV), scanning electron microscopy (SEM), UV-visible, and energy dispersive X-ray spectroscopy (EDXS). The surface coverage of gold nanoparticles on the thin film was estimated to 1.2 nanomole/cm2. An anthraquinone-2, 6-disulfonic acid, disodium salt (AQDS) self-assembled layer was generated by immersing gold thin film into 1mM of AQDS in 0.1M HClO4 solution for over 20 hours. As a result, a new absorbance peak from the multi-layers (AQDS/thin film of gold /ITO) was obtained about at 690 nm. Also, the surface plasmon absorption of multi-layers was measured by UV-Visible spectrometer along with chronoamperometry by applying the various potentials from +0.5V to -0.5V. The maximum surface plasmon absorption band at 550 nm was decreased by applying negative potentials. The change of absorbance was correlated with the surface coverage of the AQDS indicating the pseudo-capacity surface state of the AQDS layer was coupled to the energy level of the plasmonband by applied negative potentials.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.383-383
• /
• 2014

최근 디스플레이, 태양전지 그리고 touch screen panels 등 optoelectronic 장치의 시장이 성장함에 따라 투명전극의 수요가 증가하고 있다. Indium tin oxide (ITO)의 좋은 특성 때문에 주로 투명전극에 많이 사용되고 있다. 그러나 화학적 안정성이 떨어지고, 휘어질 때 특성저하가 심하여 금속나노와이어, 탄소나노튜브, 전도성폴리머, 그리고 그래핀 등의 다른 투명전극의 연구가 활발히 진행되고 있다. 그 중에서 그래핀은 높은 전자 이동도(200000 cm2v-1s-1)와 휘어져도 전기적 크게 변하지 않는 특성 때문에 유망한 투명 전도성 전극 (Transparent Conductive Electrodes, TCEs)으로 연구되어왔다. 또한 다양한 속성 가운데, 높은 광 투과성은 그래핀의 가장 큰 장점이다 [1]. 최근, 화학 기상 증착 (Chemical Vapor Deposition, CVD) 등 다양한 제조 방법이 대량 생산을 위해 개발되었다. 그러나 이 방법은 비용이 많이 들며, 과정이 상당히 복잡하고 높은 온도 (${\sim}1000^{\circ}C$)를 필요로 한다. 따라서 용매 기반의 환원된 그래핀 산화물(Reduced Graphene Oxides, RGOs)이 최근 주목 받고 있다. 그러나 RGOs의 면저항이 높아 전극으로서 사용이 제한된다. 따라서 전기적 특성을 향상시키는 방법으로 단일 벽 탄소 나노튜브 (Single-Walled Carbon Nanotubes, SWNTs)를 혼합하거나 화학적 도핑을 통하여 면저항을 크게 향상시키는 연구가 활발히 진행되고 있다. 그러나 이런 화학적 도핑의 경우 박막이 공기 중에 직접 산소나 습기와 반응하여 전기적 특성이 저하되는 문제점을 가지고 있다 [2]. 이러한 문제를 해결하기 위해 AuCl3을 도핑한 박막에 내열성 및 내광성 등의 화학적 안정성이 뛰어난 PEDOT:PSS를 코팅하여 필름의 공기중의 노출을 막아 줌으로써 도핑의 안전성 및 전기적 특성을 최적화하였다. 본 연구에서는 간단한 dip-coating방법을 사용하여 4개의 RGO/SWNTs 박막을 흡착하였다. 다음으로 AuCl3를 도핑하여 면저항 $4.909K{\Omega}$, $4.381K{\Omega}$인 두 개의 샘플의 시간과 온도에 따른 면저항의 변화를 확인하였다. 그리고 필름의 도핑 안전성을 향상 시키기 위해 AuCl3를 도핑한 필름 위에 전도성 폴리머 PEDOT:PSS 코팅하여 면저항 $886.1{\Omega}$, $837.5{\Omega}$인 두 개의 샘플의 시간과 온도에 따른 면저항의 변화를 확인하였다. AuCl3 도핑된 필름의 경우 공기 중에 150시간 노출 시 72%의 면저항 증가가 발생하였지만 PEDOT:PSS가 코팅된 필름의 경우 5%의 면저항 증가가 나타나 확연한 차이를 보였다. 또한 AuCl3 도핑한 필름의 경우 $150^{\circ}C$에서 60시간동안 공기중에 노출되었을 때 525%의 면저항 증가가 발생하였지만 PEDOT:PSS가 코팅된 필름의 경우 58%의 면저항 증가를 나타내었다. 이것은 PEDOT:PSS가 passivation역할을 하여 필름이 공기에 노출된 부분을 막아주어 도핑된 필름의 면저항의 변화를 줄여 주었음을 알 수 있다.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.7-11
• /
• 2014

Recently, the buffer layers consisting of poly (3,4-ethylenedioxythiophene): poly (styrenesulfonate) (PEDOT-PSS) are extensively used to improve power conversion efficiency (PCE) of organic solar cells. However, PEDOT-PSS is not suitable for mass production of organic solar cells due to its intrinsic acid and hygroscopic properties. Moreover, because of chemical reactions between indium tin oxide (ITO) layer and PEDOT-PSS layer, the interface is not stable. For these reasons, alternative materials such as $V_2O_5$ have been developed to be an effective buffer layer. In this work, we used $V_2O_5$/Ag/ITO multilayer structure for the anode buffer layer. With variation of thickness of Ag layer, we investigated the optical and electrical properties of $V_2O_5$/Ag/ITO multi-layer films. As a result, we found that the electrical properties were improved with increasing Ag thickness while optical transmittance decreases in visible wavelength region. From the calculation of figure of merit (FOM) which is used to evaluate proper structure for transparent of optoelectronic, $V_2O_5$/Ag/ITO multilayer electrode was optimized with 4 nm thick Ag layer in optical (88% in transmittance) and electrical ($4{\times}10^{-4}{\Omega}cm$) properties. This indicates that $V_2O_5$/Ag/ITO multilayer electrode could be a candidate for the anode of optoelectronic devices.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.128-128
• /
• 2018

최근 디스플레이 기술은 보다 가볍고, 얇고, 선명한 스마트 형태로 발전되고 있다. 특히 스마트산업의 성장으로 터치스크린패널(Touch Screen Panel, TSP)을 사용하는 기술이 다양해짐에 따라 더 높은 감도와 해상도를 달성하기 위한 핵심기술이 필요한 실정이다. TSP는 저항막 방식, 정전용량 방식, 적외선 방식, 초음파 방식 등 다양한 방식이 있다. 그 중 정전용량방식 터치 패널 (Capacitive type touch panel, CTTP)은 다른 유형에 비해 빠른 반응속도 및 멀티 터치 기능 등의 이점을 가지고 있기 때문에 연구의 초점이 되고 있다. 이를 실현하기 위해서 CTTP은 가시광영역의 높은 투과율과 낮은 비저항을 필요로 하기 때문에 박막의 초 슬림화 및 고 결정화도가 선행되어야만 한다. CTTP에 사용되는 투명전극 소재 중에서 40%의 비중을 차지하고 있는 ITO박막은 내구성과 시인성이 좋으나 생산 비용이 비싸다는 단점이 있다. 한편, 반응성 스퍼터링은 기존에 단일 소결체를 사용한 DC마그네트론 스퍼터링법보다 높은 증착률과 낮은 생산 비용으로 초박막을 만들 수 있다는 장점을 가진다. 본 실험에서는 In/Sn (2wt%) 금속 합금 타깃을 사용한 반응성 스퍼터링법을 이용하여 기판 온도 (RT 및 $140^{\circ}C$)에서 두께 30 nm의 In-Sn-O (ITO)박막을 증착하고, 대기 중 $140^{\circ}C$ 온도에서 시간에 따라 열처리한 후 박막의 물성을 관찰하였다. 증착 중 기판 가열을 하지 않은 ITO 박막의 경우, 열처리 시간이 증가함에 따라 비저항은 감소하였고, 홀 이동도는 현저하게 증가하였으며 캐리어 밀도에서는 별다른 차이가 없었다. 이를 통해 비저항의 감소는 캐리어 농도보다는 결정화를 통한 이동도의 증가와 관련 있다는 것을 확인할 수 있었다. 열처리 시간에 따른 박막의 핵 생성 및 결정 성장은 투과 전자 현미경(TEM)으로 명확하게 확인하였으며, 완전 결정화 된 박막의 grain size는 300~500 nm로 확인되었다. 기판온도 $140^{\circ}C$에서 증착한 박막의 경우, 후 열처리를 하지 않은 상태에서도 이미 결정화 된 것을 확인할 수 있었으며, 후 열처리 시에도 grain size에는 큰 변화가 없었다. 이는 증착 중에 박막의 결정화가 이미 완결된 것으로 판단된다. 또한, RT에서 증착한 박막의 경우에는 후 열처리 초기에는 산소공공등과 같은 결함들의 농도가 감소하여 투과율이 증가하였으나 완전한 결정화가 일어난 후에는 투과율이 약간 감소한 것을 확인할 수 있었다. 이는 결정화 시 박막의 표면 조도가 증가하였고 이로 인해 빛의 산란이 증가하여 투과율이 감소한 것으로 판단된다. 이러한 결과로 반응성 스퍼터링 공정으로 제조한 ITO 초박막은 후열처리에 의한 완전한 결정화를 이룰 수 있으며, 이를 통해 얻은 낮은 비저항과 높은 투과율은 고품질 TSP에 적용될 가능성을 가진다고 판단된다.