• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1994년도 특별강연 및 춘계학술발표 개요집
• /
• pp.136-141
• /
• 1994

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 1999년도 제2회 총회 및 춘계학술발표회
• /
• pp.44-44
• /
• 1999

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.78-89
• /
• 1997

This study has evaluated the weld metal solidification cracking behavior of several Ni base superalloys (Incoloy 825, Inconel 718 and Inconel 600). Austenitic stainless steels(304, 310S) were also included for comparison. In addition, a possible mechanism of solidification cracking in the fusion zone was suggested based on the extensive microstructural examinations with SEM, EDAX, TEM, SADP and AEM. The solidification cracking resistance of Ni base superalloys was found to be far inferior to that of austenitic stainless steels. The solidification cracking of Incoloy 825 and Inconel 718 was believel to be closely related with the Laves-austenite (Ti rich in 825 and Nb rich in 718) and MC-austenite eutectic phases formed along the grain boundaries during solidification. Cracking in Inconel 600 was always found along the grain boundaries which were enriched with Ti and P. Further, solidifidcation cracking resistance was dependent not only upon the type of love melting phases but also on the amount of the phases along the solidification grain boundaries.

• 한국세라믹학회지
• /
• 제56권4호
• /
• pp.387-393
• /
• 2019

A N₂H₄-Cu(I)-HNO₃ solution was used to dissolve magnetite powders and a simulated oxide film on Inconel 600. The addition of Cu(I) ions to N₂H₄-HNO₃ increased the dissolution rate of magnetite, and the reaction rate was found to depend on the solution pH, temperature, and [N₂H₄]. The dissolution of magnetite in the N₂H₄-Cu(I)-HNO₃ solution followed the contracting core law. This suggests that the complexes of [Cu⁺(N₂H₄)] formed in the solution increased the dissolution rate. The dissolution reaction is explained by the complex formation, adsorption of the complexes onto the surface ferric ions of magnetite, and the effective electron transfer from the complexes to ferric ions. The oxide film formed on Inconel 600 is satisfactorily dissolved through the successive iteration of oxidation and reductive dissolution steps.

• 한국표면공학회지
• /
• 제51권5호
• /
• pp.291-296
• /
• 2018

In this study, we carried out an ultrasonic-chemical decontamination process with immersion type, reproduced in the laboratory. The corrosion damage characteristics, depending on kind of materials and ultrasonic process time, were investigated. Inconel 600, which showed lower corrosion potential and higher corrosion current density than that of STS 316, revealed severer corrosion damage and higher weight-loss rate than STS 316. Weight-loss rate of Inconel 600 increased with increasing ultrasonic process time. On the other hands, STS 316 presented a negligibly small corrosion damage, which was almost indistinguishable from visual observation. There was no effect of ultrasonic process time on the weight-loss rate of STS 316.

• 대한기계학회논문집A
• /
• 제36권1호
• /
• pp.43-50
• /
• 2012

본 논문은 레이저 샥 피닝(LSP) 유한요소 시뮬레이션 관련 변수들이 인코넬 alloy 600 합금의 잔류 응력에 미치는 영향을 분석하였다. 특히, 레이저 피닝 공정 관련 변수인 최대 압력파, 압력파 지속시간, 레이저 스팟 크기 및 다중 레이저 샷의 영향을 확인하였다. 최대 압력파 및 압력파 지속시간은 alloy 600 재료물성에 따라 특정 범위에서 최대 압축잔류응력을 생성시켜 준다. 이 때문에 LSP 공정에서 최대 압력파 및 압력파 지속시간은 중요한 선택 변수가 된다. 일정한 크기 이상의 레이저 스팟은 잔류응력에 특별한 영향을 미치지 않음을 확인하였고, 다중 레이저 샷은 압축잔류응력 크기와 소성변형 발생깊이를 동시에 증가시키지만, 증가량은 레이저 샷 횟수가 증가할수록 감소하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.304-309
• /
• 2002

Fretting wear test in room temperature water was performed to evaluate the wear coefficient of Inconel 600,690 (Pressurized Water Reactor, PWR) and Alloy 800 (CANadian DeuteriumUranium, CANDU) steam generator (SG) tubes against ferritic and martensitic stainless steels. The main focus is to compare the wear behaviors between Alloy 800 and Inconel alloys. Test conditions are $10{\sim}30N$ of normal load, $200{\sim}450{\mu}m$ of sliding amplitude and 30Hz of frequency. The result indicated that the wear rate of Alloy 800 was higher than those of Inconel 690 at various test condition such as normal loads, sliding amplitudes etc. From the results of SEM observation, there was little evidence of plastic deformation layer that were dominantly formed on the worn surfaces of Inconel 690. Also, wear particles in Alloy 800 were released from contacting asperities deformed by severe plastic flow during fretting wear. Main cause of wear rate between Alloy 800 and Inconel 690 may be due to the difference of hardness between martensitic and ferritic stainless steel. The wear rate and wear mechanism of two tubes in room temperature water are discussed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.125-128
• /
• 1995

The remote sleeve repair-welding technology using the pulsed Nd:YAG laser for increasing the lifetime of the steam generator tube in the nuclear power plant has been developed. The laser welding has many advantages on deep penetration depth and narrow heat affect zone(HAZ). The inconel 600 tube and inconel 690 sleeve used high temperature and high pressure service have been welded as round lap welds. It is found that the relation between the connection width and welding parameters. It is found that the shear strength in proportion to the connection width by conducting tensile-shear tests.

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.49-53
• /
• 2002

Inconel 690 for nuclear steam generator tube has more chromium than the conventionally used Inconel 600 in order to increase the corrosion resistance. TD evaluate the tribological characteristics under fretting condition the fretting tests as well as sliding tests were carried out in elevated temperature water environment. Fretting tests of the cross-cylinder type were done under various vibrating amplitudes and applied normal loads in order to measure the friction forces and wear volumes. Also, the conventional sliding tests of pin-en-disk type were carried out to compare the test results. In fretting, the friction was very sensitive to the load and the amplitude. The friction coefficient decreased with increasing load and decreasing amplitude. Also, the wear of Inconel 690 can be predictable using the work rate model. Depending on normal loads and vibrating amplitudes, distinctively different wear mechanisms and of ten drastically different wear rates can occur. It was fecund that the fretting wear coefficients in water were increased as increasing the temperature of water.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.2047-2052
• /
• 2004

Inconel-600 alloy has been used as steam generator tube material for current pressurized water reactors (PWRs). The long-term operation of steam generators showed that the use of this material induced localized corrosion damages and increased tube wear of steam generator. To protect these problems, steam generator tube material is being changed to Inconel-690 alloy. Based on the current trend, we have chosen Inconel 690 as the Advanced Power Reactor 1400 (APR1400) steam generator(SG) tube material and performed the design optimization of preventive measure against tube fretting wear for the APR1400 steam generator. In this paper, we examined the technical consideration in this modification : the selection of material, wear characteristics, effect of the Egg-crate Flow Distribution Plate installation, and effect analysis of vertical strip installation.