• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.2
• /
• pp.200-209
• /
• 1998

Experiments have been conducted to determine heat transfer characteristics for a two-dimen-sional turbulent wall attaching offset jet at different oblique angles to a flat surface. The local Nusselt number distributions were measured using liquid crystal as a temperature sensor. Wall static pressure coefficient profiles were measured at the Reynolds number Re 53200(based on the nozzle width, D) the offset ratio H/D from 2.5 to 10 and the oblique angle a from $0^{\circ}$, to $40^{\circ}$ It is observed that the maximum Nusselt number point occurs slightly upstream of time-averaged reattachment point for all oblique angles. The correlations between the maximum Nusselt number and Reynolds number offset ration and oblique angle are presented.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.180-184
• /
• 2009

A novel set of experimental test tooling for measuring pulling and holding forces for drawbeads on binders inclined at a wide range of angles is introduced. A mechanical design featuring a single load cell, a male-female draw bead set, translation and rotation degrees of freedom, and a screw-driven clamping system has been incorporated into a standard tensile test machine. On a real time basis, restraining and holding force data with respect to draw-in displacement may be directly downloaded into a PC for data processing. The proposed experimental system represents a significant breakthrough in drawbead simulation technology due to its relatively low cost, clever design, and versatility. The system is shown to yield excellent experimental data suitable for verifying theory and numerical model predictions.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.1
• /
• pp.11-17
• /
• 2007

The amount of incident rays over inclination according to direction has been widely utilized as important data in installing photovoltaic systems. This is because the performance of the photovoltaic systems in much affected by angle and direction of incident rays. Recognizing that factors mentioned above are of importance, actual experiment on the moving route of the sun have been performed in this research to obtain the angle of inclination with which the maximum incident rays can be absorbed. After all, the standard for designing highly optimized photovoltaic systems will be provided for designers and employees working in the photovoltaic module related industries.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.911-920
• /
• 2013

Experimental studies on both subcooled and saturated pool boiling of water were performed to obtain local heat transfer coefficients on a $3^{\circ}$ inclined tube of 50.8 mm diameter at atmospheric pressure. The local values were determined at every $45^{\circ}$ from the very bottom to the uppermost of the tube periphery. The maximum and minimum local coefficients were observed at the azimuthal angles of $0^{\circ}$ and $180^{\circ}$, respectively, in saturated water. The locations of the maxima and the minima were dependent on the inclination angle of the tube as well as the degree of subcooling. The major heat transfer mechanisms were considered to be liquid agitation generated by the sliding bubbles and the creation of big size bubbles through bubble coalescence. As a way of quantifying the heat transfer coefficients, an empirical correlation was suggested.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.11
• /
• pp.39-51
• /
• 2009

This is a study on rectangular-shaped passive row piles in inclined sand-ground by model tests. The experiment controlled the angle of inclination of ground and induced the ground destruction. We also measured the behavior of row piles, by adjusting the shape, position and spacing of piles. As a result, we confirmed the earth pressure, the lateral resistance, and the effect of depressing on the ground variation working on passive pile. The effect of B-type pile of which the front width is wide is bigger than that of H-type pile of which the side width is wide. We can find out the failure angle of slope, the shared force of pile and soil by using the lateral resistance graph based on slope angle.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.495-496
• /
• 2008

This paper describes the influence of Ultra-violet irradiation on time to tracking resistance of epoxy insulating materials by use of the inclined plane test. And, the influence of surface degradation was evaluated through several method such as measurement of contact angle, surface roughness, using a scanning electron microscopy. As the 1000 hours of the surface degradation with UV-CON, the flashover time decreases at different rates depending on epoxy resin and silicone rubber specimen. As the duration of the surface degradation with UV-CON is prolonged, the contact angle of epoxy resin decreases at the rate of degradation time, while that of silicone rubber was not exchanged. It is assumed that this phenomenon is related to the decrease in hydrophobicity of the surface of the materials. Also, as to epoxy resin, the decrease of hydrophobicity due to surface degradation with UV-CON is greater than that resulting from surface degradation with WOM. The UV radiation produced chalking and crazing on the surface of the insulating materials specimen.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.890-893
• /
• 2000

In this paper, the test of machinability according to the cutting positions when the ball end milling of hemispheric workpiece is carried out to find the optimum cutting position of free form surface die. Tool runout, cutting force. and chip form are measured. The results show that the optimum cutting condition to get the constant feed per tooth is the inclined angle of 40 degree of workpiece.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.328-333
• /
• 2003

The purpose of this study is to analyze the impact of shot peening angle on residual stress distribution. From the residual stress analysis of perpendicular shot peening, it could be known that the residual stress in the case of high velocity is larger than low velocity, but the amount of shot size has little effect on the magnitude of compressive residual stress. The centroidal residual stress is not greatly affected by the inclined shot peening but mainly related to the unstable conditions of surface residual stress field. Therefore, this tendency may lead to reduce fatigue life of treated material.

• Journal of The Korean Society of Integrative Medicine
• /
• v.10 no.3
• /
• pp.131-140
• /
• 2022

Purpose : Although many studies have explored the effect of seating side angles on the spinal curve and surrounding muscles during seating, only a few studies have investigated the effect of different seating face angles on different lower limb and deep trunk muscles. Therefore, this study investigated the effects of seating surface angles (0 degrees, 10 degree anterior, and 10 degree rear) on lower extremity and deep trunk muscles in healthy adults. Methods : Thirty people were asked to sit once on each seating surface three times during the day, and their muscle thicknesses were measured by ultrasound while sitting. The method of sitting was the same when sitting on the three seating surfaces. Results : From the comparison results of the muscle thicknesses according to the seating surface angles, a significant difference existed in the muscle thicknesses of the vastus medialis, vastus medialis oblique, vastus intermedius, soleus and gastrocnemius (p<.05). However, no significant difference was found in the transversus abdominis, internal obliques, rectus femoris and vastus lateralis (p>.05). Conclusion : Our findings revealed that the lower back load decreases, the leg load increases, and the legs specific muscles are affected as the body tilts forward when sitting on the seating surface inclined forward. Therefore, it is possible to suggest a forwardly inclined seating surface that reduces lower back loads and utilizes the posture-maintaining muscles of the legs when sitting in a person with a poor sitting posture or lower back pain at ordinary times.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.3
• /
• pp.294-300
• /
• 1983

The purpose of this study is to investigate the radiant emission characteristics of diffuse equi-lateral trapezoid groove cavity for the case of uniform surface temperature. The theoretically developed results for the apparent emissivity are presented and the values of apparent emissivity for the trapezoid groove cavity were compared with those of the V-groove cavity. In the experimental part of this study, the test models were manufactured from 100x 100x 15mm copper plates on which the equi-lateral trapezoid cavities were grooved. The inclined angles of the groove were 30,45 and 60 degrees and the ratio of groove depth to base surface width varied from 1 to 5 for each inclined angle. As a result of this work, it was found that the trapezoid groove cavity was more general form of V-groove and the apparent emissivity of trapezoid groove cavity was greater than that of V-groove cavity. The resulting equation for the apparent emissivity in the trapezoid groove cavity was valid for the angles greater than 40 degrees.