• Journal of the Optical Society of Korea
• /
• v.16 no.4
• /
• pp.349-353
• /
• 2012

Uniform spreading of injection current in light-emitting diodes (LEDs) is one of the crucial requirements for better device performances. It is reported that non-uniform current spreading leads to low output power, high current crowding, heating, and reliability degradation of the LED device. This paper reports on the effects of different surface and electrode geometries in the LEDs. To increase the output power of LEDs and reduce the series resistance, a rectangular-type LED (RT-LED) with a centered island cathode has been fabricated and investigated by comparison with a conventional LED (CV-LED). The performances of RT-LEDs were prominently enhanced via uniform current spreading and low current crowding. Performances in terms of increased output power and lower forward voltage of simulated RT-LEDs are much superior to those of CV-LEDs. Based on these results, we investigated the correlation between device geometries and optical characteristics through the fabricated CV and RT-LEDs. The measured output power and forward voltage of the RT-LEDs at 100 mA are 64.7% higher and 8% smaller compared with those of the CV-LEDs.

• Journal of the Korean Ceramic Society
• /
• v.44 no.3 s.298
• /
• pp.147-151
• /
• 2007

An improvement for the efficiency of the $Sr_{2}SiO_{4}:Eu$ yellow phosphor under the $450{\sim}470\;nm$ excitation range have been achieved by adding the co-doping element ($Mg^{2+}\;and\;Ba^{2+}$) in the host. White LEDs were fabricated through an integration of an blue (InGaN) chip (${\lambda}_{cm}=450\;nm$) and a blend of two phosphors ($Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor) in a single package. The InGaN-based two phosphor blends ($Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor) LEDs showed three bands at 450 nm, 550 nm and 640 nm, respectively. The 450 nm emission band was due to a radiative recombination from an InGaN active layer. This 450 nm emission was used as an optical transition of the $Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor. As a consequence of a preparation of white LEDs using the $Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor yellow phosphor and CaS:Eu red phosphor, the highest luminescence efficiency was obtained at the 0.03 mol $Ba^{2+}$ concentration. At this time, the white LEDs showed the CCT (5300 K), CRI (89.9) and luminous efficacy (17.34 lm/W).

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.2
• /
• pp.81-86
• /
• 2023

Recently, there has been an increased demand for light-emitting diode (LED) due to the growing emphasis on environmental protection. However, the use of GaN-based sapphire in LED manufacturing leads to the generation of defects, such as dislocations caused by lattice mismatch, which ultimately reduces the luminous efficiency of LEDs. Moreover, most inspections for LED semiconductors focus on evaluating the luminous efficiency after packaging. To address these challenges, this paper aims to detect defects at the wafer stage, which could potentially improve the manufacturing process and reduce costs. To achieve this, image processing and deep learning-based defect detection techniques for Sapphire Epi-Wafer used in Green LED manufacturing were developed and compared. Through performance evaluation of each algorithm, it was found that the deep learning approach outperformed the image processing approach in terms of detection accuracy and efficiency.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.391-392
• /
• 2008

A SPICE-based 3-dimensional circuit model of Light-Emitting Diode(LED) was modified include the reverse breakdown properties. The new model is found to be accurate to study the failure mechanisms of LEDs under electrostatic discharge (ESD) and electronic overstress (EOS). It was found that the permanent damages under heavy reverse stress is mainly due to the high electric field strength in P-GaN layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.418-419
• /
• 2013

현재, 인듐 주석 산화물(indium tin oxide, ITO) 박막은 가시영역에서 전기적 특성 및 광학적 특성이 우수하기 때문에 평면 디스플레이(flat displays), 박막 트랜지스터(thin film transistors), 태양전지(solar cells) 등을 포함한 광소자에 투명전도성산화물(transparent conducting oxide, TCO) 전극으로 가장 일반적으로 사용되고 있다. 하지만, 이 물질은 밴드갭이 3.4 eV로 다소 작아 다양한 분야의 의료기기, 환경 보호에 응용 가능한 자외선 영역에서 상당히 많은 양의 광흡수가 발생하는 치명적인 문제점을 가지고 있다. 또한, 인듐(Indium)의 급속한 소비는 인듐의 매장량의 한계로 인해 가격을 상승시키는 주요한 원인으로 작용하고 있다. 한편, InGaN 기반의 자외선 발광다이오드 분야에서는 팔라듐(Pd) 기반의 반투명 전극과 은(Ag) 기반의 반사전극을 주로 사용하고 있지만, 낮은 투과도와 낮은 굴절률을 때문에 여전히 자외선 발광다이오드의 광추출 효율(extraction efficiency)에 문제점을 가지고 있다. 따라서 자외선 발광다이오드의 외부양자 효율(external quantum efficiency, EQE)을 높이기 위해 높은 투과도와 GaN와 유사한 굴절률을 가지는 p-형 오믹 전극을 개발해야 한다. 본 연구에서는 초박막의 ITO (16 nm)/Ag (7 nm)/ITO (16 nm) 다층 구조를 갖는 투명전도성 전극을 제작한 후, 열처리 온도에 따른 전기, 광학적 특성에 향상에 대해서 조사하였다. 사용된 산화물/금속/산화물 전극의 구조는 유기발광 다이오드(organic light emitting diode, OLED), 태양전지 등에 많이 사용되는 안정적인 투명 전극을 자외선 LED 소자에 처음 적용하여, ITO의 전체 사용량은 줄이고, ITO 사이에 금속을 삽임함으로써 금속에 의한 전기적 특성 향상과 플라즈몬 효과에 의한 투과도를 높일 수 있는 장점을 가지고 있다. 실험 결과로는, $400^{\circ}C$에서 열처리한 ITO/Ag/ITO 다층 구조는 365 nm에서 84%의 광학적 특성과 9.644 omh/sq의 전기적 특성을 확인하였다. 실험 결과로부터 좀 더 최적화를 수행하면, ITO/Ag/ITO 다층 구조는 자외선 발광다이오드의 투명전도성 전극으로 사용될 수 있을 것이라 기대된다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.11-11
• /
• 2008

ZnO has a very large exciton binding energy (60 meV) as well as thermal and chemical stability, which are expected to allow efficient excitonic emission, even at room temperature. ZnO based electronic devices have attracted increasing interest as the backplanes for applications in the next-generation displays, such as active-matrix liquid crystal displays (AMLCDs) and active-matrix organic light emitting diodes (AMOLEDs), and in solid state lighting systems as a substitution for GaN based light emitting diodes (LEDs). Most of these electronic devices employ the electrical behavior of n-type semiconducting active oxides due to the difficulty in obtaining a p-type film with long-term stability and high performance. p-type ZnO films can be produced by substituting group V elements (N, P, and As) for the O sites or group I elements (Li, Na, and K) for Zn sites. However, the achievement of p-type ZnO is a difficult task due to self-compensation induced from intrinsic donor defects, such as O vacancies (Vo) and Zn interstitials ($Zn_i$), or an unintentional extrinsic donor such as H. Phosphorus (P) doped ZnO thin films were grown on c-sapphire substrates by radio frequency magnetron sputtering with various Ar/ $O_2$ gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio with out post-annealing. The P-doped ZnO films grown at a Ar/ $O_2$ ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of $10^{-17}cm^{-3}$ and $2.5cm^2/V{\cdot}s$, respectively. X-ray diffraction showed that the ZnO (0002) peak shifted to lower angle due to the positioning of $p^{3-}$ ions with a smaller ionic radius in the $O^{2-}$ sites. This indicates that a p-type mechanism was due to the substitutional Po. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction LEO showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.5
• /
• pp.324-329
• /
• 2018

Red phosphor in glasses (PiGs) for automotive light-emitting diode (LED) applications were fabricated with 620-nm $CaAlSiN_3:Eu^{2+}$ phosphor and Pb-free silicate glass. PiGs were synthesized and mounted on high-power blue LED to make a monochromatic red LED. PiGs were simple mixtures of red phosphor and transparent glass powder. After being fabricated with uniaxial press and CIP at 300 MPa for 20 min, the green bodies were thermally treated at $550^{\circ}C$ for 30 min to produce high dense PiGs. As the phosphor content increased, the density of the sintered body decreased and PiGs containing 30% phosphor had a full sintered density. Changes in photoluminescence spectra and color coordination were studied by varying the thickness of plates that were mounted after optical polishing. As a result of the optical spectrum and color coordinates, PiG plate with $210{\mu}m$ thickness showed a color purity of 99.7%. In order to evaluate the thermal stability, the thermal quenching characteristics were measured at temperatures of $30{\sim}150^{\circ}C$. The results showed that the red PIG plates were 30% more thermally stable compared to the AlGaInP red chip.

• Journal of IKEEE
• /
• v.17 no.3
• /
• pp.221-228
• /
• 2013

About functional parameters of a LED/UVLED (Light Emitting Diode/Ultra Violet LED), one of the most important parameters is the I-V characteristic. By researching factors affect to the I-V characteristic of uvled, we found that beside of the structure of the device itself, there is the influence of the electrode materials, electrode shapes, the process of wiring and packaging. In this work, we want to improve the performance of UVLED to find out the optimal mask design principles. The study is based on theoretical mathematical models, as well as the use of simulation software tool Comsol. From all results obtained, the team has improved mask design to manufacture electrodes for GaN-based UVLED. Electrode masks are designed by three softwares, which are Intellisuite, Klayout and AutoCad. Intellisuite masks would be used in fabrication simulation while Klayout and AutoCad are used to fabricate electrodes in experiments. As well as, we silmulated the structure of an uvled 355nm emission wavelength by TCAD software, in order to compare with uvled sample that has the same emission wavelength.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.7 s.349
• /
• pp.1-6
• /
• 2006

We show for the first time the optical properties of the selectively oxidized vertical cavity laser (VCL) - depleted optical thyristor (DOT), which has not only a low threshold current, but also a high sensitivity to the optical input light. In order to analyze their switching characteristics, nonlinear s-shaped current-voltage characteristics are calculated and the reverse full-depletion voltages (Vneg's) are obtained as function of semiconductor parameters by using a finite difference method (FDM). The selectively oxidized PnpN VCL-DOT clearly shows the nonlinear s-shaped current-voltage and lasing characteristics. A switching voltage of 5.24 V, a holding voltage of 1.50 V, a spectral response at 854.5 nm, and a very low threshold current of 0.65 mA is measured, making these devices attractive for optical processing applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.256-256
• /
• 2010

투명전극부터 디스플레이 산업에 이르기까지 광범위하게 응용되어지고 있고 개발되어지고 있는 투명전도산화물(TCO)은 ZnO, In2O3, SnO2 등을 기본으로 하는 n-type 재료가 대부분이다. 그러나 투명전도 산화물을 이용한 light emitting diode(LED), 투명한 태양전지, p-형 TFT와 같은 투명전자소자의 개발을 위해서는 p-type 소재가 필수적이다. p-type TCO 소재는 비교적 연구 개발 실적이 매우 부진한 실정이었다. 1997년 넓은 밴드갭을 가지는 ABO2(delafossite) 산화물이 p-type으로서 안정적이라는 것을 보고함에 따라 이에 대한 연구가 활발히 진행되고 있다. 현재 ABO2 형태를 가진 Delafossite구조 산화물이 가장 유망한 p-type 투명전도체 소재로 거론되고 있다. Delafossite 구조가 p-type 투명전도체에 적합한 결정구조인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. Delafossite구조는 상온에서 2종류의 polytype(상온에서 Rhombohedaral구조와 hexagonal 구조)이 존재하며 이들은 각각 3R 및 2H의 결정 구조를 가지고 있다. ABO2의 delafossite구조에서 Cu+의 배열은 c-축을 따라 Cu-O-Cr-O-Cu의 연속적인 층 구조로서 2차원연결로 보여 진다. 보고된 Cu- base delafossite구조를 가지는 재료들은 CuAlO2, CuGaO2, CuInO2 등 여러가지가 있다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Zn를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 산소분압을 $500{\sim}700^{\circ}C$, 0~10mTorr로 변화시켜 특성을 연구하였다. 성장온도 $700^{\circ}C$, 산소분압 10mTorr에서 c-plane 사파이어 기판위에 c-축 배향의 에피성장된 CuCrO2:Zn 박막을 얻을 수 있었다. Mg를 도핑함에 따른 p-type 특성보다 현저히 떨어지는 것을 확인하였다. 또한 동일한 조건임에도 특정한 이차상의 존재를 통해 도핑된 Zn의 위치를 추측할 수 있었다. 온도와 분압에 따른 결정성과 표면상태를 SEM을 통해서 확인하였다.