• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.518-523
• /
• 1999

In thi, study, we made experiments to fonn a mesa shape by meltback method with various concentration of solutions and found that unsaturated (20%) InGaAsP (1.55 !-tm) solution at a growth temperature was the most suitable for the formation of a mesa ,hape on the wafer which has an InGaAsP active layer and an InP cap layer on an n-InP substrate. It was difficult to form a proper mesa shape for the fabrication of PBH-LDs only by the meltback method; therefore, we fabricated PBH-LDs by forming the mesa shape with the meltback method after wet etching and by growing a current-blocking layer successively. As the electrical and optical charaleri,tiecs of MQW-PBH-LDs fabricated by above methods, when the cavity length was $300{\mu}m$, the threshold current was about 10 mA, internal quantum efficiency 82%, internal loss $9.2cm^{-1}$, and characteristic temperature was 65 K at $25~45^{\circ}C$ and 42 K at $45~65^{\circ}C$. /TEX>.

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.35-39
• /
• 2011

The PSPICE equivalent circuit elements of a 1550 nm InGaAsP laser diode were derived by using multi-level rate equations. The device parameters were extracted by using a self-consistent numerical method for the optical gain properties of the MQW active regions. The resulting equivalent circuit model is also applied to an actual optical transmitter, and its PSPICE simulation results show good agreement with the measured results once the parasitic capacitance due to the packaging is taken into account.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.583-589
• /
• 2019

We report experimental results on 940-nm 350-mW AlGaAs/InGaAs transverse single-mode laser diodes (LDs) adopting graded-index separate confinement heterostructures (GRIN-SCH) and p,n-clad asymmetric structures, with improved temperature and small-divergence beam characteristics under high-output-power operation, for a three-dimensional (3D) motion-recognition sensor. The GRIN-SCH design provides good carrier confinement and prevents current leakage by adding a grading layer between cladding and waveguide layers. The asymmetric design, which differs in refractive-index distribution of p-n cladding layers, reduces the divergence angle at high-power operation and widens the transverse mode distribution to decrease the power density around emission facets. At an optical power of 350 mW under continuous-wave (CW) operation, Gaussian narrow far-field patterns (FFP) are measured with the full width at half maximum vertical divergence angle to be 18 degrees. A threshold current (I_th) of 65 mA, slope efficiency (SE) of 0.98 mW/mA, and operating current (I_op) of 400 mA are obtained at room temperature. Also, we could achieve catastrophic optical damage (COD) of 850 mW and long-term reliability of 60℃ with a TO-56 package.

• ETRI Journal
• /
• v.30 no.3
• /
• pp.480-482
• /
• 2008

A novel InGaAsP/InP buried-ridge waveguide laser diode structure is proposed and demonstrated for use as a single-mode laser. The lateral mode of the proposed device can be controlled by adjusting the composition and thickness of the InGaAsP layer grown over the active region. Stable single-mode operation without kinks or beam-steering is achieved successfully with lateral and transverse in the junction plane even for the device with the ridge width of 9 ${\mu}m$ up to an injection current of 500 mA.

• Journal of the Optical Society of Korea
• /
• v.14 no.1
• /
• pp.38-41
• /
• 2010

We design and fabricate a widely tunable laser diode made of InGaAsP-InP. The diode is monolithically integrated with a wavelength-selective coupled-ring reflector and semiconductor amplifiers. For realization of a compact size device, deeply etched multi-mode interference couplers and square ring resonators composed of total-internal-reflection mirrors are adopted and fabricated using a self-aligned process. It is demonstrated that the laser diode exhibits single mode operation and 16 nm tuning range with side-mode-suppression-ratio exceeding 20 dB.

• Journal of Periodontal and Implant Science
• /
• v.40 no.3
• /
• pp.105-110
• /
• 2010

Purpose: It has been reported that low-level semiconductor diode lasers could enhance the wound healing process. The periodontal ligament is crucial for maintaining the tooth and surrounding tissues in periodontal wound healing. While low-level semiconductor diode lasers have been used in low-level laser therapy, there have been few reports on their effects on periodontal ligament fibroblasts (PDLFs). We performed this study to investigate the biological effects of semiconductor diode lasers on human PDLFs. Methods: Human PDLFs were cultured and irradiated with a gallium-aluminum-arsenate (GaAlAs) semiconductor diode laser of which the wavelength was 810 nm. The power output was fixed at 500 mW in the continuous wave mode with various energy fluencies, which were 1.97, 3.94, and 5.91 $J/cm^2$. A culture of PDLFs without laser irradiation was regarded as a control. Then, cells were additionally incubated in 72 hours for MTS assay and an alkaline phosphatase (ALPase) activity test. At 48 hours post-laser irradiation, western blot analysis was performed to determine extracellular signal-regulated kinase (ERK) activity. ANOVA was used to assess the significance level of the differences among groups (P<0.05). Results: At all energy fluencies of laser irradiation, PDLFs proliferation gradually increased for 72 hours without any significant differences compared with the control over the entire period taken together. However, an increment of cell proliferation significantly greater than in the control occurred between 24 and 48 hours at laser irradiation settings of 1.97 and 3.94 $J/cm^2$ (P<0.05). The highest ALPase activity was found at 48 and 72 hours post-laser irradiation with 3.94 $J/cm^2$ energy fluency (P<0.05). The phosphorylated ERK level was more prominent at 3.94 $J/cm^2$ energy fluency than in the control. Conclusions: The present study demonstrated that the GaAlAs semiconductor diode laser promoted proliferation and differentiation of human PDLFs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.111.2-111
• /
• 1998

• Korean Journal of Materials Research
• /
• v.8 no.5
• /
• pp.419-423
• /
• 1998

The conditions for optimizing mass transport for making buried heterostructure (BH) InGaAsP/lnP lasers are discussed. The double heterostructure InGaAsP/lnP laser structures were grown by Liquid Phase Epitaxy (LPE) and etched into mesas. The active layer was selectively etched along [llO] and the mass transport was carried out in the LPE reactor to cover the sides of the active layer and form a BH structure. The threshold temperature for the appreciable mass transport is measured to be 670$670^{\circ}C$ when the holding time is set to 40 min. The width of the region re¬filled by mass transport is observed to increase as the temperature increases.

• Korean Journal of Optics and Photonics
• /
• v.32 no.2
• /
• pp.55-61
• /
• 2021

The lateral-mode characteristics of 850-nm GaAs/(Al,Ga)As multiple-quantum-well laser diodes and their influence on the kinks in output optical power are investigated. For the investigation, self-consistent electro-thermal-optical simulation and measurement of fabricated devices are used. From this investigation, the optimal P-cladding thickness that provides single-lateral-mode operation is determined, so that high beam quality can be achieved even at high output powers.

• Proceedings of the Optical Society of Korea Conference
• /
• 1999.08a
• /
• pp.216-217
• /
• 1999

A tapered ridge mode laser diode with increased spot size is designed and analyzed . The mode evolution concept is applied to design the taper and the method does not require regrowth or multiple-step etching technique. Three-dimensional BPM results show that the designed taper can transfer more than 97% of the mode power in the active region to the expanded mode.