• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.9
• /
• pp.1358-1365
• /
• 2016

The purpose of this study was to verify the drying characteristics of seasoned red pepper sauce and establish optimal drying conditions for far infrared drying of seasoned red pepper sauce. Seasoned red pepper sauce, which was dried by heated air, was used. One kg of seasoned red pepper was spread at thicknesses of 10 and 20 mm and dried by a far infrared dryer until a final moisture content of $15{\pm}0.5%$. The far infrared dryer conditions were air velocity of 0.6, 0.8 m/s and drying temperatures of 60, 70, and $80^{\circ}C$. The drying models were estimated using a determination coefficient and root mean square error. Drying characteristics were analyzed based on factors such as drying rate, color changes, content of capsaicinoids, and energy consumption. The results can be summarized as follows. The drying rate (that is, drying time) tended to be reduced as temperature and air velocity for drying increased. The Page and Henderson models were suitable for drying of seasoned red pepper sauce by a far infrared dryer. Redness decreased after far infrared drying under all experimental conditions. The color difference was 18.18 under the following conditions: thickness 20 mm, temperature $70^{\circ}C$, and air velocity 0.8 m/s. This value was slightly higher than those under other far infrared drying conditions. The capsaicinoid properties of seasoned red pepper sauce decreased under all far infrared drying conditions. The highest capsaicin (19.91 mg/100 g) and dihydrocapsaicin (12.87 mg/100 g) contents were observed at a thickness of 10 mm, temperature of $80^{\circ}C$, and air velocity of 0.8 m/s. Energy consumption decreased with higher temperature, slower air velocity, and thinner seasoned red pepper sauce.

• Journal of Korean Society of Transportation
• /
• v.25 no.4
• /
• pp.123-133
• /
• 2007

This study analyzed whether a transit network with hierarchy is efficient or not, and if transit network hierarchy has cost efficiency, then which condition guarantees the efficiency of the transit network hierarchy. The authors modeled the total cost of the transit network and suggested the conditions in which the transit network hierarchy has cost efficiency through comparing the cost of the transit network with and without hierarchy. The efficiency of transit network hierarchy is guaranteed when the travel cost savings induced by using a higher hierarchy transit network is larger than the increasing non-travel cost, which is the sum of access cost, waiting cost, and operating cost, induced by the introduction of a higher hierarchy transit network. This result is consistent with common sense and with the concept of cost and benefit analysis. If a passenger traveling within the area divided by a higher hierarchy transit network uses only a lower hierarchy transit network and the passenger traveling out of the area divided by the higher hierarchy transit network uses both lower and higher hierarchy transit networks, the travel demand using the higher hierarchy transit network is inversely proportional to the square of the line spacing. This means that the transit network becomes more efficient and small increases of travel demand guarantee the efficiency of the transit network hierarchy as the connectivity of the network becomes higher. This result shows that transit networks have economies of aggregation. This study is the first analytical research on transit network hierarchy and is expected to be a basis for numerical research. However, numerical research should complement this study, since analytical research has some limitations for considering a real network.

• Journal of Life Science
• /
• v.19 no.12
• /
• pp.1802-1807
• /
• 2009

Platycodin D, a major component of Platycodi radix, is known to have various activities including anti-inflammatory, anti-hyperlipidemic, anti-tumor activities and others. Recently, it was reported that platycodin D inhibits fat accumulation and adipogenesis. The aim of this study was to investigate whether various adipogenic regulators are modulated by platycodin D treatment during the adipogenesis of 3T3-L1 cells. mRNA levels of terminal markers of adipogenesis such as ADIPOQ (adiponectin) and GLUT (glucose transporter) 4, which were quantified by real time PCR, were decreased by platycodin D treatment. mRNA expression of PPAR (peroxisome proliferator-activated receptor) $\gamma$ and C/EBP (CCAAT/enhaner binding protein) $\alpha$, which are central transcription factors of adipogenesis, were also decreased by platycodin D treatment. To elucidate the detailed molecular mechanism of platycodin D-induced inhibition of adipogenesis, we analyzed mRNA expression of upstream regulators of PPAR$\gamma$ and C/EPB$\alpha$. mRNA levels of the pro-adipogenic regulators, KROX20 and KLF (Kruppel-like factor) 15 were markedly down-regulated by platycodin D treatment. On the other hand, mRNA expression of CHOP (C/EBP homologous protein), an anti-adipogenic regulator, was significantly up-regulated by platycodin D treatment. mRNA levels of other pro-adipogenic regulators, C/EBP$\beta$ and C/EPB$\delta$, were not affected by platycodin D treatment, and another anti-adipogenic regulator, C/EBP$\gamma$ was also not affected by platycodin D treatment. Taken together, these results suggest that platycodin D-induced inhibition of adipogenesis is mediated by gene interactions including the down-regulation of pro-adipogenic regulators, KROX20 and KLF15, and the up-regulation of an anti-adipogenic regulator, CHOP.

• Proceedings of the Korean Society for Food Science of Animal Resources Conference
• /
• 2006.05a
• /
• pp.146-150
• /
• 2006

도축 후 2일째 가열 감량은 시험구(골반골 현수)가 대조구(아킬레스건 현수)에 비하여 유의적으로 감량이 높았으나, 드립량에 있어서는 반대의 결과를 보였으며, 전체 감량은 두 처리구간 차이가 없었다. 연도의 지표인 전단력가는 대조구 $6.45kg/cm^2$로 시험구 $5.52kg/cm^2$에 비하여 유의적으로 높았으며, 골반골 현수를 통하여 도축 후 8일차의 대조구의 전단력 수준을 보여 숙성기간을 약 1주일 정도 단축이 가능하였다. 근절길이는 대조구 $1.93{\mu}m$, 시험구 $2.48{\mu}m$로 시험구가 유의적으로 길어 골반골 현수에 의한 단축 억제 효과로 볼 수 있다. 관능 평가 결과 도축후 2일차에는 대조구에 비하여 시험구가 다즙성, 연도, 향미, 기호성에서 유의적으로 높은 값을 보였으나, 도축 후 8일째에는 대조구와 시험구간에 차이를 보이지 않았다. 출하 연령과 현수방법에 따른 대퇴이두근의 물리적 특성을 비교한 결과로서 근절길이는 모든 월령에서 시험구가 대조구에 비하여 길었다. 전단력은 시험구가 대조구에 비하여 유의적으로 낮은 결과를 보였다. 골반골 현수에 의한 전단력가 감소 효과는 출하 월령이 많을수록 효과가 큰 것으로 나타났다. 드립 발생율은 대조구가 시험구에 비하여 유의적으로 높은 경향을 보였다. 가열 감량과 보수성은 처리구에 관계없이 유의적인 차이를 보이지 않았다. 관능 특성을 비교한 결과 30개월 미만의 경우에는 유의적인 차이를 보이지 않았으나, 30개월 이상에서는 처리구가 대조구에 비하여 다즙성 연도, 향미, 기호성 모두 우수한 것으로 나타났다. 특히 골반골 현수는 출하 월령이 증가됨에 따라 관능 특성의 개선율이 높은 것으로 나타났다. 수 있다.분별을 성공적으로 수행하였다.(p<0.05), 맛, 연도, 다즙성 및 전체적인 기호성은 유의한 차이가 없었다.자체를 악하다고 볼 수 없고 더구나 구원을 이 세상에서의 이탈로 볼 수 없다. 진정한 구원이란 원래 하나님이 보시기에 아름다웠던 그 세상으로의 회복을 포함한다. 이런 면에서 하나님 주권 신앙 하에서 구원이란 전 인격적인 구원, 전 우주적인 구원이 된다. 그렇기 때문에 성도는 세상의 삶과 학문, 예술, 정치, 경제, 사회를 포함한 모든 분야를 하나님의 뜻 가운데서 그 원래의 목적에 부합할 수 있도록 회복시키는 일에 적극 참여해야 한다.자체가 이를 주도하기는 사실 어려움이 있다. 그리고 대형유통점이 영업행위를 영업시간제한에서부터 출점제한에 이르기까지 규제하는 건은 심사숙고하여야 한다. 대형유통점이 국가경제 및 지역사회에 미치는 영향이 부정적인가 긍정적인가에 대해 국내외 학계와 업계에서 여전히 많은 논란이 있기 때문이다. 정부와 지자체에 의한 시장개입은 반드시 필요한 경우에 한해 합당한 방법에 의해 이루어져야 한다. 대형유통점에 대한 규제는 지역사회에 미치는 영향을 다면적으로 평가한 결과에 근거하여 이루어져야 할 것이다. 대부분의 지자체는 체계적인 평가시스템과 객관적인 통계 자료를 갖고 있지 못한 실정이다. 향후 가장 시급한 과제는 시장개방 이후 지난 10년간 대형유통점이 지역사회에 미친 영향에 관한 광범위한 통계자료를 수집하고 이를 체계적으로 분석하여 정책방향을 올바르게 설정하는 것이라 할 수 있다.i와 K. pneumoniae가 존재하며 확산 중임을 시사한다. 앞으로 CTX-M형 ESBL의 만연과 변종 CTX-M형 ESBL의 출연을 감시하기 위한 정기적인 연구와 조사가 필요한 것으로 생각한다., A2-1, B1-1, B2-1의 경우,

• Journal of Plant Biotechnology
• /
• v.39 no.3
• /
• pp.140-145
• /
• 2012

The flowering locus T (FT) gene, of which expression will be controlled at high temperature by heat shock promoter (it printed as to HSproFT), was introduced into spray-type chrysanthemum (Dendranthema grandiflorum (Ramat.) Kitamura) 2 cultivars ('Pink PangPang' and 'Pink Pride' by co-cultivation with Agrobacterium tumefaciens strain C58C1 harboring pCAMBIA2300 containing the HSproFT gene. After leaf segments of the 2 cultivars were infected with the A. tumafaciens with C58C1 as explants, shoots were regenerated from the explants cultured on the $1^{st}$ selection medium (MS basal salts + 1.0 mg/L BA, 0.5 mg/L IAA + 10 mg/L kanamycin + 0.7% plant agar, pH 5.8). The shoots were transferred into the $2^{nd}$ selection medium (MS basal salts + 1.0 mg/L BA, 0.5 mg/L IAA + 20 mg/L kanamycin + 0.7% plant agar, pH 5.8). One hundred seventeen plantlets from 'Pink PangPang' and 5 ones from 'Pink Pride' were confirmed as transformants by PCR analysis. Twenty six of the transformants and non-transformants were acclimatized and established well in a green house. Eights of 26 transgenic lines showed flower bud 1.7~10 days earlier than nontransgenic plants, and 24 of them flowered 1~6 days earlier than non- transgenic plants. The shape and color of flower of all HSproFT-transgenic lines were not different with those of non- transgenic plants.

• Journal of the Korean Magnetics Society
• /
• v.15 no.2
• /
• pp.100-105
• /
• 2005

$Ni_{0.9}Zn_{0.1}Fe_2O_4$ nanoparticles have been prepared by a sol-gel method. The structural and magnetic properties have been investigated by DTA/TGA, XRD, SEM, and $M\ddot{o}ssbauer$ spectroscopy, VSM. $Ni_{0.9}Zn_{0.1}Fe_2O_4$ powder that was annealed at $300^{\circ}C$ has spinel structure and behaved superparamagnetically. The estimated size of superparammagnetic Ni-Zn ferrite nanoparticle is around 10 nm. The hyperfine fields at 13 K for the A and B patterns were found to be 533 and 507 kOe, respectively. The blocking temperature ($T_B$) of superparammagnetic $Ni_{0.9}Zn_{0.1}Fe_2O_4$ nanoparticle is about 250 K. The magnetic anisotropy constant and relaxation time constant of $Ni_{0.9}Zn_{0.1}Fe_2O_4$ nanoparticle were calculated to be $1.6\times10^6\;ergs/cm^3$ and ${\tau}_0=5.0{\times}10^{-13}$ s, respectively. Also, Temperature increased up to $43^{\circ}C$ within 10 minutes under AC magnetic field of 7 MHz. It is considered that $Ni_{0.9}Zn_{0.1}Fe_2O_4$ powder that was annealed at $300^{\circ}C$ is available for biomedicine application such as hyperthermia, drug delivery system and contrast agents in MRI.

• Journal of the Korean Magnetics Society
• /
• v.27 no.4
• /
• pp.123-128
• /
• 2017

The magnetic isotropy property from the magnetoresistance (MR) curve and magnetization (MH) loop for the PtMn based spin valve (SV) multilayer films fabricated with different the bottom structure after post-annealing treatment was investigated. The exchange biased coupling field ($H_{ex}$), coercivity ($H_c$), and MR ratio of Glass/Ta(10 nm)/CoFe(6 nm)/Cu(2.5 nm)/CoFe(3 nm)/Ta(4 nm) SV multilayer film without antiferromagnetic PtMn layer are 0 Oe, 25 Oe, and 3.3 %, respectively. MR curve for the Glass/Ta(10 nm)/CoFe(6 nm)/Cu(2.5 nm)/CoFe(3 nm)/PtMn(6 nm)/Ta(4 nm) SV multilayer film showed $H_{ex}=2Oe$, $H_c=316Oe$, and MR (%) = 4.4 % with one butterfly MR curve having by the effect of antiferromagnetic PtMn layer. MR curve for the dualtype Glass/Ta(10 nm)/CoFe(6 nm)/Cu(2.5 nm)/CoFe(3 nm)/PtMn(6 nm)/CoFe(3 nm)/Cu(2.5 nm)/CoFe(6 nm)/Ta(4 nm) SV multilayer film showed $H_c=37.5Oe$ and 386 Oe, MR = 3.5 % and 6.5 % with two butterfly MR curves and square-like hysteresis MH loops. The anisotropy property in CoFe spin valve-PtMn multilayer is neglected by the effects of a very small value of $H_{ex}$ and a very slightly shape magnetic anisotropy. This result is possible to explain the effect of magnetization configuration spin array of the bottom SV film and the top SV film of PtMn layer.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.1
• /
• pp.31-36
• /
• 2013

Maritime University cadets must be on board ship's after thoroughly completing a Basic Safety Training Course. During their spare semester they must complete basic principle of the course and then, attend to both Advanced Safety Training Course and Tankers Training Course before they graduate. However, all cadets are exposed to risks during their onboard training. It means that most of commercial ships have to train them before boarding and perform duties according to all sorts of check lists based on the ISM. Accordingly, this research will deal with the treatment for toxic chemicals which is not fully covered by shipping firms, vessels and even a Maritime University for cadets. The lack of pre-knowledge about it is considerably hazardous to the cadets who have no onboard experience. As stated above, the majority of the onboard cadets board their ships without previous training on treatment and knowledge for toxic chemicals. As a result, there are some cases that cadets are injured due to the lack of knowledge to treat toxic chemicals and due to carelessness. Furthermore, they end up leaving a ship prematurely. To prevent these incidents from occurring, this paper recommends thorough training before going onboard provided by Maritime University, the systematic database on the safety of the toxic chemicals and the development of the online contents for safety education of toxic chemicals fitted on each ship's types are necessary to avoid risks and accidents onboard. Furthermore, it is suggested that shipping companies should manage the ship according to the safety check list on toxic chemicals and the crew in charge with qualification for the treatment of toxic chemicals should provide a safety education and supervision.

• Fire Science and Engineering
• /
• v.32 no.1
• /
• pp.46-56
• /
• 2018

The paper relates to a study on the conduction heat transfer characteristics according to the heating temperature of lightweight panel wall material. Plywoods, marbles, heat resistant glasses, as well as general gypsum board and fire-proof gypsum board, which have been widely used for lightweight panel wall material, were selected as experiment samples, and heating temperatures were set as $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$. Next, each of the heating temperatures were introduced on the bottom part of the wall material for 30 minutes, and analyses were made on the heat transfer characteristics to the backside part on the top part through conduction. As results of the experiment, the maximum backside temperatures were measured up to $190^{\circ}C$ for a general gypsum board, $198^{\circ}C$ for a fire-proof gypsum board, $189^{\circ}C$ for a plywood, $321^{\circ}C$ for a marble, and $418^{\circ}C$ for a heat resistant glass as heating temperatures were introduced maximum of $600^{\circ}C$. In addition, the maximum change rate of conduction heat transfer were measured up to 85 W for a general gypsum board, 95 W for a fire-proof gypsum board, 67 W for a plywood, 1686 W for a marble, and 3196 W for a heat resistant glass as the maximum heating temperatures were introduced up to $600^{\circ}C$. Also, carbonization characteristics of the wallpapers were measured to visually check the danger of conduction heat transfer, and the results showed that smokes were first generated on the attached wallpapers for the heating temperature $600^{\circ}C$, which were 1021 s for a general gypsum board, 978 s for a fire-proof gypsum board, 1395 s for a plywood, 167 s for a marble, and 20 s for a heat resistant glass, and that the first generation of carbonization were 1115 s for a general gypsum board, 1089 s for a fire-proof gypsum board, 1489 s for a plywood, 192 s for a marble, and 36 s for a heat resistant glass.

• The Korean Journal of Pesticide Science
• /
• v.3 no.2
• /
• pp.47-53
• /
• 1999

Photosensitizing activities of some photosensitizers (PS) for the artificial diminution of pesticide residues on horticultural crops were investigated. Five fungicides, iprodione, bitertanol, chlorothalonil, myclobutanil, and dichlofluanid were sprayed on apple and cucumber, followed by the application of each selected photosensitizer, and the samples were collected 0, 1, 3, 7, 15 days after the photosensitizer application and analyzed for the residual amounts. Of the 40 photosensitizers tested, six selected on the basis of the eliminating effect of pesticide residues were PS-1 (aromatic ketone), PS-2 (aromatic amine), PS-3 (quinone), PS-4 (inorganic compound), PS-5 (organic acid salt), and PS-6 (semiconductor photocatalyst). The residual amount of iprodione after 15 days of the application of PS-1 was 74% of that of the control. For bitertanol, the residual amount after 15 days of the application of PS-1 accounted for 78% of that of the control. The residual amounts of chlorothalonil after 1 day of the application of PS-1 and PS-2 accounted for 56 and 54% of those of the control, respectively. The residual amounts of iprodione on cucumber after 3 days of the application of the photosensitizers PS-1 and PS-2 were 44 and 67% of those of the untreated control, respectively. For myclobutanil, the residual amount after 15 days of the application of PS-6 accounted for 45% of that of the control. In case of dichlofluanid, the residual amount after 3 days of the application of PS-1 accounted for 44% of that of the control. Based on the results, PS-1 turned out to be the most promising photosensitizer for the accelerated photodegradation of the above fungicides on apple and cucumber.