• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.5
• /
• pp.669-674
• /
• 2012

This study presents the remote control of a mobile robot using iPhone based on Wi-Fi communication. The paper proposes the following set of user interfaces : acceleration mode, arrow touch mode, and jog-shuttle mode. To evaluate the proposed three interfaces, a virtual robot is controlled in a monitor to follow a referenced trajectory using iPhone. In simulation, the standard deviation and summed errors are analysed for showing good and weak points of the proposed three interfaces. The proposed interface replace an additional remote controller requiring cost with a cellular phone. Results of an experiment show that the proposed interfaces can be effectively used for remote robot control.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.20 no.2
• /
• pp.23-32
• /
• 2010

WiBro(Wireless Broadband), the service based on IEEE 802.16e(mobile WiMAX) standard, is a wireless broadband Internet technology being developed by the domestic telecommunication industry. In this paper, we analyze security vulnerabilities of WiBro focusing on initial authentication phase and propose a specification-based intrusion detection system that can detect those vulnerabilities. We first derive a specification from the normally operational process of the initial authentication based on PKMv2 EAP-AKA and formalize the derived specification as a state transition diagram. Proposed system executes the intrusion detection based on those specification and state transition diagram. In this paper, to verify the detection capability of proposed system, we construct a test bed network and execute scenario-based test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.834-841
• /
• 2012

In order to the mobile service uses the wireless terminal including the development of the wire wireless network and Smart phone, and etc. use including mobile office, which and etc. increases. Because in order that the u-Healthcare service using this appeared before the footlights and the existing quality measurement reference considered the speed, error rate, and etc. just, guarantees the stability of the u-Healthcare, the quality control by service are necessary. In this paper, the quality measurement reference by mobile service considering the radio environment as the method for satisfying the quality guarantee of the u-Healthcare mobile service user and user needs was presented. The WiBro u-Healthcare wireless data service quality based system in the end user perspective was established through the main performance index and entrepreneur case presented in the international standardization institute including 3GPP, WiMAX forum, GSMA, and etc. through the related research and the validity of the quality index establishment was presented according to each service.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11A
• /
• pp.844-851
• /
• 2009

Handover is needed in multi-hop relay systems to support mobility. The main purpose of handover is to provide the continuous connection when a MS migrates from the air-interface of one BS to another air-interface provided by another BS. Especially the handover between different systems is essential to next generation network. Vertical Handover technology in Mobile WiMAX MMR system is very useful for operators to introduce to Mobile WiMAX system in an overlaid cell environment. This technology will be applied to technology which hands MRS(Mobile Relay Station) over to different systems for system performance enhancement in Ubiquitous environment overlaid between Micro ce11(Frequency 1,FA1) and Macro cell(Frequency 2,FA2). In this paper, FA1 and FA2 are used in order to perform Vertical Handover of MRS(Mobile Relay Station) according to suggested conditions. interferences from neighboring BS or other sectors of 6 macro cells surrounding center Macro cell are analyzed and throughputs are measured according to suggested conditions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.4
• /
• pp.612-623
• /
• 2022

Estimation of the presence of people in real time is extremely useful for businesses in providing better services. Many companies and researchers have attempted various researches in order to count the number of floating population in a specific space. Recently, as part of smart cities and digital twins, commercialization of measuring floating populations using Wi-Fi signals has become active in the public and private sectors. In this paper we present a method of estimating the floating population based on MAC-address values collected from smartphones. By distinguishing Real MAC-address and Random MAC-address values, we compare the estimated number of smartphone devices and the actual number of people caught on CCTV screens to evaluate the accuracy of the proposed method. And it appeared to have a similar correlation between the two datas. As a result, we present a method of estimating the floating population based on analyzing Wi-Fi Probe Requests.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.836-841
• /
• 2016

An indoor positioning system using Wi-Fi is essential to produce a radio map that combines the indoor space of two or more dimensions, the information of node positions, and etc. in processing for constructing the radio map, the measurement of the received signal strength indicator(RSSI) and the confirmation of node placement information counsume substantial time. Especially, when the installed wireless environment is changed or a new space is created, easy installation of the node and fast indoor radio mapping are needed to provide indoor location-based services. In this paper, to reduce the time consumption, we propose an algorithm to distinguish the straight and curve lines of a corridor section by RSSI visualization and Sobel filter-based edge detection that enable accurate node deployment and space analysis using cable-type Wi-Fi node installed at a 3 m interval. Because the cable type Wi-Fi is connected by a same power line, it has an advantage that the installation order of nodes at regular intervals could be confirmed accurately. To be able to analyze specific sections in space based on this advantage, the distribution of the signal was confirmed and analyzed by Sobel filter based edge detection and total RSSI distribution(TRD) computation through a visualization process based on the measured RSSI. As a result to compare the raw data with the performance of the proposed algorithm, the signal intensity of proposed algorithm is improved by 13.73 % in the curve section. Besides, the characteristics of the straight and the curve line were enhanced as the signal intensity of the straight line decreased by an average of 34.16 %.

• The KIPS Transactions:PartC
• /
• v.18C no.4
• /
• pp.265-278
• /
• 2011

The objective of this paper is to analyze and characterize end-to-end packet statistics after modeling and simulation of WiFi (IEEE 802.11g) and WiMAX (IEEE 802.16e) of a virtual wireless network using OPNET Modeler Wireless Suite. Wireless internal and external network simulators such as Remcom's Wireless InSite Real Time (RT) module, WinProp: W-LAN/Fixed WiMAX/Mobile WiMAX, and SMI system, are designed to consider data transfer rate based on wireless propagation signal strength. However, we approached our research in a different perspective without support for characteristic of these wireless network simulators. That is, we will discuss the purpose of a visual analysis for these packets, how to receive each point packets (e.g., wireless user, base station or access point, and http server) through end-to-end virtual network modeling based on integrated wired and wireless network without wireless propagation signal strength. Measuring packet statistics is important in QoS metric analysis among wireless network performance metrics. Clear packet statistics is an especially essential metric in guaranteeing QoS for WiMAX users. We have found some interesting results through modeling and simulation for virtual wireless network using OPNET Modeler Wireless Suite. We are also able to analyze multi-view efficiency through experiment/observation result.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.5
• /
• pp.944-949
• /
• 2015

This study proposed a patch antenna with a MIMO structure which is applicable for wireless communication equipment by combining a single patch antenna with a multi port. The proposed MIMO patch antenna was designed through the TRF-45 substrate with a relative permittivity of 4.5, loss tangent equal to 0.0035 and dielectric high of 1.6 mm, and the center frequency of the antenna was 2.45 GHz in the ISM (Industrial Scientific and Medical) band. The proposed MIMO patch antenna had a 500 MHz bandwidth from 2.16 ~ 2.66 GHz and 24.1% fractional bandwidth. The return loss and VSWR were -62.05 dB, 1.01 at the ISM bandwidth of 2.45 GHz. The Wibro band of 2.3 GHz was -17.43 dB, 1.33, the WiFi band of 2.4 GHz was -31.89 dB, 1.05, and the WiMax band of 2.5 GHz was -36.47 dB, 1.03. The radiation patterns included in the bandwidth were directional, and the WiBro band of 2.3 GHzhad a gain of 4.22 dBi, the WiFi band of 2.4 GHz had a gain of 4.12 dBi, the ISM band of 2.45 GHz had a gain of 4.06dBi, and the WiMax band of 2.5 GHz had a gain of 3.9 6dBi.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.5
• /
• pp.515-522
• /
• 2008

In this paper, a slot antenna with built-in Bazooka balun aimed for a WiBro repeater was designed and fabricated. The return loss and radiation pattern of the slot antenna were improved due to the introduced Bazooka balun. This balun brings about even radiation pattern and keeps the stabilized coverage of repeater And it is easy to unite this balun with the antenna body by providing the terminal of Bazooka balun with screw shape. H-type slot was used to reduce the size of the antenna, and the slot antenna was fabricated in the structural symmetry with respect to a feeding point to afford the omni-directional radiation pattern. The simulated results were obtained by MWS(Microwave Studio Simulator) of CST company, and the measurement on the proposed antenna was conducted in an anechoic chamber equipped with a network analyzer and a far field measurement system. The measured peak gain shows 5.75 dBi and the average gain is above -0.8 dBi. The return loss remains below -12.35 dB for all frequency bands in WiBro regarded as a good performance.

• Journal of Platform Technology
• /
• v.9 no.4
• /
• pp.51-59
• /
• 2021

In this paper, we propose a location-based service that the user's location is known by connection history to WI-FI AP installed in a facility known its location previously. The location-based service proposed in this paper manages job processing states of technicians who inspect and maintain the facility like elevator by using worker's location and arrival time information. The job scheduling management method proposed in this paper is based on previously scheduled arrival time and actual arrival time to a target facility. And we experimentally implemented the inspection and maintenance system of an elevator to show the feasibility of job schedule management based on location and arrival time information acquired from Wi-Fi AP connection history. Our experimental implementation shows that our proposed method is usefulness in the field of the inspection and maintenance of a facility.