• 한국정밀공학회지
• /
• 제32권10호
• /
• pp.897-902
• /
• 2015

This study reports on a uniform resin coating method by using a doctor blade type dispenser. For high productivity, continuous imprint-lithography has been studied, and developed fabrication systems are used in several applications such as anti-reflection films, dry adhesives, and water collecting surfaces. In the continuous fabrication field, researchers have typically focused on patterning and demolding procedures. During the roll-to-roll fabrication process, however, the uniform resin coating process is also important in order to obtain a high quality product, which can be evaluated by uniform thickness, precise geometric expressions, and a thin residual layer. To achieve these, a doctor blade type dispenser was designed and fabricated. As a result, thickness of coated resin was well controlled by modulating the flow rate of the resin and blading gap. In addition, a very thin layer coating process (${\sim}10{\mu}m$) was achieved by softly contacting the blade on the substrate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.672-675
• /
• 2005

To imprint 70-nm wide line-patterns, we used a newly developed ultraviolet nanoimprint lithography (UV-NIL) process in which an elementwise patterned stamp (EPS), a large-area stamp, and pressurized air are used to imprint a wafer in a single step. For a single-step UV-NIL of a 4' wafer, we fabricated two identical $5'\times5'\times0.09'(W{\times}L{\times}H)$ quartz EPSs, except that one is with nanopatterns and the other without nanopatterns. Both of them consist of 16 small-area stamps, called elements, each of which is $10\;mm\;\times\;10\;mm$. UV-curable low-viscosity resin droplets were dispensed directly on each element of the EPSs. The volume and viscosity of each droplet are 3.7 nl and 7 cps. Droplets were dispensed in such a way that no air entrapment between elements and wafer occurs. When the droplets were fully pressed between ESP and wafer, some incompletely filled elements were observed because of the topology mismatch between EPS and wafer. To complete those incomplete fillings, pressurized air of 2 bar was applied to the bottom of the wafer for 2 min. Experimental results have shown that nanopatterns of the EPS were successfully transferred to the resin layer on the wafer.

• Tribology and Lubricants
• /
• 제24권5호
• /
• pp.255-263
• /
• 2008

Adhesion tests were conducted to investigate the adhesion characteristics between mold and thermoplastic polymer film. Coating of anti-sticking layer (ASL), a kind of polymer material, imprint pressure, and separation velocity were considered as the process conditions. A piece of fused silica without patterns on its surface was used as a mold and the thermoplastic polymer films were made on Si substrate by spin-coating the commercial polymer solution such as mr-I PMMA and mr-I 7020. The ASL was derived from (1H, 1H, 2H, 2H - perfluorooctyl) trichlorosilane($F_{13}$-OTS) and coated on the fused silica mold in vapor phase. The pull-off force was measured in various process conditions and the surfaces of the mold and the polymer film were observed after separation. It was found that the adhesion characteristics between the mold and the thermoplastic polymer film and the release performance of ASL were changed according to the process conditions. The ASL was effective to reduce the pull-off force and the damage of polymer film. In cases of the mold coated with ASL, the pull-off force did not depend on imprint pressure and separation velocity.

• 소성∙가공
• /
• 제14권5호
• /
• pp.473-476
• /
• 2005

The demand of on-chip total analyzing system with MEMS (micro electro mechanical system) bio/chemical sensor is rapidly increasing. In on-chip total analyzing system, to detect the bio/chemical products with submicron feature size, a filtration system with nano-filter is required. One of the conventional methods to fabricate nano-filter is to use direct patterning or RIE (reactive ion etching). However, those procedures are very costly and are not suitable fur mass production. In this study, we suggested new fabrication method for a nano-filter based on replication process, which is simple and low cost process. After the Si master was fabricated by laser interference lithography and reactive ion etching process, the polymeric mold was replicated by UV-imprint process. Metallic nano-filter was fabricated after removing the polymeric part of metal deposited polymeric mold. Finally, our fabrication method was applied to metallic nano-filter with $1{\mu}m$ pitch size and $0.4{\mu}m$ hole size for bacteria sensor application.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.364-367
• /
• 2007

In nano-imprint lithography (NIL) process, which has shown to be a good method to fabricate polymeric patterns, several kinds of pattern defects due to thermal effects during polymer flow and mold release operation have been reported. A typical defect in NIL process with high aspect ratio and low resist thickness pattern is a resist fracture during the mold release operation. It seems due to interfacial adhesion between polymer and mold. However, in the present investigation, FEM simulation of NIL molding process was carried out to predict the defects of the polymer pattern and to optimize the process by FEA. The embossing operation in NIL process was investigated in detail by FEM. From the analytical results, it was found that the lateral flow of polymer resin and the applied pressure in the embossing operation induce the weld line and the drastic lateral strain at the edge of pattern. It was also shown that the low polymer-thickness result in the delamination of polymer from the substrate. It seems that the above phenomena cause the defects of the final polymer pattern. To reduce the defect, it is important to check the initial resin thickness.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.502-505
• /
• 2007

PMMA has been extensively adopted in Nano Imprint Lithography(NIL). PMMA nano-structures experience severe mechanical load and deformation during NIL process, and understanding its mechanical behavior is very important in designing and optimizing NIL process. One of the most promising techniques for characterizing the mechanical behavior of nano structures is nano pillar compression test. In this study, the mechanical behaviors of PMMA pillars during compression test are analyzed using Molecular Dynamics. Two methods for simulation of PMMA nano pillars are proposed. The stress-strain relationship of nano-scale PMMA structure is obtained based on CVFF(Covalent Valence Force Fields) potential and the dependency of the applied strain rate on the stress-strain relationship is analyzed. The obtained stress-strain relationships can be useful in simulating nano-scale PMMA structures using Finite Element Method(FEM) and understanding the experimental results obtained by compression test of PMMA nano pillars.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.63-63
• /
• 2010

나노 구조를 제작은 나노 기술을 기반으로 하는 electronics, optoelectronics, sensing, ultra display등의 여러 분야에서 이용되고 있다. 특히 나노 구조를 갖는 금속 패터닝의 경우 전자빔 리소 그래피 (electron beam lithography)나 레이저 패터닝(laser patterning)과 같은 방법들이 많이 사용되고 있다. 하지만 공정이 복잡하고 그로 인해 공정 비용이 많이 든다는 단점이 있었다. 나노 임프린트 리소그래피 기술은 master mold 표면의 나노 패턴을 가열, 가압 공정을 통해 기판 위의 고분자 레지스트 층으로 전사하는 기술이다. 이 기술은 간단한 공정을 통해 나노 패턴을 형성할 수 있는 기술이기 때용에 차세대 나노 패터닝 기술로써 각광받고 있다. 특히 이 기술은 레지스트 층과의 직접적인 접촉을 통해 나노 패턴을 형성하기 때문에 다양한 방법을 통해 기능성 나노 패턴을 직접적으로 형성할 수 있는 가능성을 지니고 있다. 본 연구는 novel meta1의 하나인 Ag 입자가 첨가된 ink solution를 master mold로부터 복제한 PDMS mold를 이용하여 다양한 구조의 나노 패턴을 만드는 방법에 대한 연구이다.

• 소성∙가공
• /
• 제18권8호
• /
• pp.616-624
• /
• 2009

In this work we demonstrate the hot-embossing process under different forming conditions such as forming temperature, load, and holding time in pressing, in order to determine the suitable conditions required for linear patterning on polymer plates (PC). Results showed that the replicated pattern depth increased in proportion to an increase in the forming temperature, load, and time. The reduction of the workpiece thickness increased according to the holding time in the pressing process. In the process of time, the reduction ratio of the workpiece thickness decreased due to the surface area increment of the workpiece, while the pressure on the workpiece declined. In order to reduce the bulging ratio we introduced a temperature difference between the upper and the lower punch.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.808-810
• /
• 2005

Inexpensive large area arrays of thin film transistors (TFTs) on flexible substrates will enable many new display products that cannot be cost effectively manufactured by conventional means. This paper presents a new approach for low cost manufacturing of electronic devices using roll-to-roll (R2R) processes exclusively. It was developed in partnership by Hewlett Packard Laboratories and Iowa Thin Film Technologies (ITFT), a solar cell manufacturer. The approach combines ITFT's unique processes for vacuum deposition and etching of semiconductors, dielectrics and metals on continuous plastic webs with a method HP has invented for the patterning and aligning the multiple layers of a TFT with sub-micron accuracy and feature size.

• 한국공작기계학회논문집
• /
• 제17권2호
• /
• pp.104-109
• /
• 2008

Nowadays, the researches for improving LCD manufacturing process and reducing cost are getting accelerated and additionally new types of process are widely developed. In this situation, APEM(Anti Photo Exposure Method) which does not need photo-lithography is realized as one of possible alternative of LCD process. APEM makes LCD pattern by stamping and it can reduce the process cost and process time because of its simplicity. But optical alignment between pattern glass and target glass is very critical fact to realize the precise patterns. So, the analysis of deflection of large size of glass is carried out and design of experiment method is applied for optimal design of jig.