• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.118-120
• /
• 2009

본 논문에서는 직접 전력변환방식의 단상 sag/swell 보상기를 구현하였다. 제안된 보상기는 정현파 입력/ 출력 필터, 직렬연결 변압기와 dc 링크 커패시터부가 없는 단상 back-to-back PWM컨버터로 구성되어 있다. 이 보상기의 장점은 dc-link 진해 커패시터가 제거되어 전력회로부가 간단하게 구현되어 향상된 신뢰성 및 내구성을 확인 할 수 있으며 동시에 단상 전압 sag/swell을 보상하며 스위칭 손실을 줄이는 간단한 PWM 방법을 들 수 있다. 더구나, 제안된 방법은 일반적인 직접 전력변환방식에서 요구되어지는 복잡한 4-step 전류 방법이 필요 없는 간단한 전류제어방법을 채용할 수 있는 구조이며 제안된 보상기의 구조와 PWM 방법의 타당성을 프로토타입 하드웨어를 제작하여 실험결과로 보상기의 우수성을 확인하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.5
• /
• pp.41-49
• /
• 2015

In this paper, we studied an optimal design and efficiency improvement of the BLCD motor used in home electronic appliance. The number of stator slots is chosen depending on the rotor poles, phase number, and the winding configuration. In general, a fractional slots/pole design is preferred to minimize cogging torque. To reduce the winding resistance, we reduced the coil length and we improved the coil space factor. We proposed three types of stator slot shape design for the optimal BLDC motor design. One of them, U-type slot shape is a best optimal design, it proved by the simulated and tested. Optimal design of essential parameters aiming at high winding factor are presented to create for a high-quality system implementation. Design analysis is verified by testing and building a prototype motor.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.615-618
• /
• 2006

The broadband power detector for direct- onversion Six-port output circuit was designed and implementaed in this paper. The power detector should linearly operated to produce the linear amplitude and phase signal fer input RF signal in required broadband. So, the power detector should be designed under conditions of matching circuit with low VSWR. The designed power detectors, which were implemented in L-band with 50 ohm matching and Ku-band with matching circuit and isolator, respectively, were evaluated in the performances.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.5
• /
• pp.818-823
• /
• 2010

Exploiting models and simulations are encouraged among the defense acquisition society, as now enforced by the Defense Aquisition Program Administration's regulations. They are useful and, sometimes, inevitable especially in an earlier phase of system development. Computer-simulation-based experimentation technique for the system operational performance analysis for a torpedo defense system is introduced in this paper. Problem definition for the torpedo defense system analysis and engineering efforts for models and simulations development are presented here, including defining measures of performance and effectiveness for the torpedo defense system, conceptual modeling for torpedo engagement and defense simulation, design of experimentation, design of simulator and experimentor, and hardware and software implementation of an analysis support tool - a system operations demonstration and experimentation simulator.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.381-388
• /
• 2011

This article presents the development of a model for SiC power diodes based on the physics of the semiconductor. The model is able to simulate the behavior of the dynamics of the charges in the N- region based on the stored charge inside the SiC power diode, depending on the working regime of the device (turn-on, on-state, and turn-off). The optimal individual calculation of the ambipolar diffusion length for every phase of commutation allows for solving the ambipolar diffusion equation (ADE) using a very simple approach. By means of this methodology development a set of differential equations that models the main physical phenomena associated with the semiconductor power device are obtained. The model is developed in Pspice with acceptable simulation times and without convergence problems during its implementation.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.550-551
• /
• 2012

정밀한 작업 공정을 요구하는 산업 현장의 전압 새그 보상이나 각종 장비의 전력 품질 시험을 하기 위해서는 전압 새그 발생의 환경 요건이 필요하다. 그러나 3상 계통 전압은 사용자가 임의로 전압 새그를 발생시킬 수 없기 때문에 장비의 성능 검사 및 각종 시험을 하기가 어렵다. 현재, 여러 가지 전압 새그 보상장치가 개발되고 있으며 이러한 장비의 성능을 검증하기 위해서는 가격이나 품질 면에서 우수한 전압 새그 발생기가 필요하다. 전압 새그 발생기를 통한 시험으로 전압 새그 보상장치의 신뢰도 향상과 예기치 못한 상황에 대한 대책을 강구할 수 있다. 본 논문에서는 전압 새그의 크기와 위상, 그리고 발생하는 구간을 조절할 수 있는 3상 전압 새그 발생장치를 설계하고 그 동작을 3kVA 프로토타입을 제작하여 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.3-4
• /
• 2012

역률개선용 변환기는 입력전류를 교류전원과 동상으로 제어하여 다이오드 정류기에 비해 역률을 개선하고 THD를 저감시킬 수 있다. 본 논문에서는 단상 역률개선용 배전압 변환기를 IP 제어기와 Anti Wind-up Control을 사용하여 출력전압의 크기를 안정되게 제어하며 PI 제어기와 Anti Wind-up Control을 사용하여 입력전류가 입력전압과 동상이 되도록 제어한다. 또한 Duty-ratio Feed Forward Control을 사용하여 디지털 제어에 의한 진상현상을 저감시킨다. 본 논문에서는 소형화와 경량화가 가능하고 출력전압이 높은 역률개선용 단상 브리지리스 배전압 변환기를 구현한다.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.689-691
• /
• 1993

This paper describes an induction heating system which is developed for CRT manufacturing. This system consists of a buck chewer, a voltage source full-bridge inverter, and a series resonant circuit with a matching transformer. A series resonant scheme is employed, and operated at the zero phase of the resonant load by PLL. This ensures maximum power transfer, good efficiency and reliability of the system. Implementation of a prototype rated of 3 kW 450 kHz is described and experimental results are given.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1047-1050
• /
• 1993

Recently, AC servo motor has expanded its application areas the to the development of the power semi-conductor and control technology. But it has large torque ripple for its nonlinear characteristics and phase commutaion. In this paper, we proposed the switching angle overlapping method, and current control using tracking method in order to generate the constant torque of AC servo motor that has the trapezoidal back e.m.f. It is compared the these types of control method with the characteristics through simulation. We show that these methods lead the torque ripple to reduce and makes the position and speed characterlistics improved effectively. Also we prove that current control using tracking method is the best way to reduce torque ripple among the these types of control method.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.219-222
• /
• 2002

In this paper, some parameters are studied for the performance improvement of a bulk optical magnetic-field sensor. The performance of optical magnetic-field sensor is influenced by optical intensity change and wavelength change of light source, and phase shift so called optical bias mismatch. A magnetic field measuring system based on optical Faraday sensor is implemented and tested in the current range from 10 ampere to 200 ampere. The test result shows implemented system has goof linearity.