• International Journal of Aeronautical and Space Sciences
• /
• 제5권1호
• /
• pp.1-5
• /
• 2004

The discharge performance of an impinging-type injector for cavitating flow has been evaluated. The predicted discharge coefficient for cavitating flow agree s well with the measured data showing less than 2% discrepancy. For the case of non- cavitating flow analysis, the disagreement between CFD resu lts and the experimental data is 8%. The discharge coefficient for the cavitating flow decreases with decrea se in the Reynolds number. On the other hand, it increases slightly as the Reynolds number increases for the non-cavitating flow because of the reduced viscous effect. The incipience of cavitation is predicted to occur around the cavitation number of 1.3 for fixed Reynolds number flow. In this environment, the discharge performance is proportional to the cavitation number for cavitating flow while it is independent to the cavitation number for non-cavitating flow regime.

• 한국분무공학회지
• /
• 제1권2호
• /
• pp.16-23
• /
• 1996

In case of a high-speed D.I. diesel engine. the injected fuel spray is unavoidable that the impinging on the wall of piston cavity and in this case the geometry of piston cavity has a great influence on the atomization structure and air flow fields. In the field of combustion and in many other spray applications, there are clear evidence of correlation between spray structure and emission of pollutants. Ordinary, the combustion chamber of driving engine have unsteady turbulent flow be attendant on such as the change of temperature, velocity and pressure. So the analysis of spray behavior is difficult. In this study, a single spray was impinged on each cavity wall at indicated angle in a quiescent atmosphere at room temperature and pressure, as being the simplest case, and 3 types of piston cavity such as Dish, Toroidal and Re-entrant type was tested for analyzing the influence of cavity geometry. And hot wire probe was used for analyze non-steady flow characteristics of impinging spray, and to investigate the behavior of spray, the aspects of concentration c(t), standard deviation $\sigma(t)$ and variation factor (v.f.) was measured with the lapse of time.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.54-61
• /
• 2001

It is reported that during the cold starting, especially in gasoline engine, the engine response and the effect of HC emission can be improved by prompting atomization and reducing the quantity of fuel adhered to the range of injector tip, inlet port, and inlet valve. The purposes of this study are to promote atomization of fuel before air-fuel mixture in the inlet port. In order to achieve its goal, the glow plug is to evaluate the feasibility of for the early fuel evaporator and the spray behavior characteristics of gasoline, injected on the surface of glow plug with room temperature(2$0^{\circ}C$) and high temperature(25$0^{\circ}C$) is to examine. Particle motion analysis system(PMAS) was used to measure the SMD and the dropsize distribution of impinging spray and free spray. The results of this experiment, evaporation rate of impinging spray was higher than that of free spray, and the higher evaporation rate win, the smaller peak dropsize was. Especially, during early spray SMD of impinging spray was still smaller than that of fee spray.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제21회 추계학술대회 논문집
• /
• pp.195-203
• /
• 2003

실물형 Unlike 충돌형 triplet 분사기인 F-O-F형과 O-F-O형의 분무특성 및 혼합특성을 실험적으로 알아보았다. 각각의 분사기에 대해 산화제와 연료의 운동량비의 변화에 따라 분무형상과 케로신/물을 이용한 혼합효율을 측정하였다. 분무형상은 Stroboscope와 CCD camera를 이용한 직접사진기법으로, 혼합효율은 Mechanical Patternator를 이용하였다. O-F-O형 분사기가 미립화 특성이 우수함을 알 수 있었고, 운동량비가 증가함에 따라 혼합효율이 급격히 감소함을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제23권1호
• /
• pp.92-103
• /
• 1999

The fuel spray behavior in the intake port of an electronic control port irijection gasoline engine has a strong influence on engine performance, exhaust emission and fuel consumption. Thus, in this study, fuel spray behavior and flow characteristics of the air assist gasoline spray injected into a suction flow in a simulated rectangular intake port have boon investigated. Macro-behavior of spray characteristics was investigated by means of visualization and the measurements of SMD and velocity were made by PDPA. For analysis the flow field with droplets size, droplets are classified five droplets size groups. As a result, the normal distance of suction flow increasing, the relatively large droplets distribution and SMD increase because small droplets easily follow suction flow. Near impinging wail, after impinging against the wall, secondary atomized small droplets of D < $30{\mu}m$ bound from the wall. And the increasement of suction flow progress to the large droplets of D > $100{\mu}m$ distribution. Therefore, SMD are apparently increased near impinging wall, Z/d = 9.0.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.214-221
• /
• 1987

본 논문에서는 2차원충돌분류에서 사각리브(rib)를 갖는 요철형전열면에 대한 실험에 관한 것이며, 리브의 높이를 (ｅ=5nm) 일정하게 하고 리브의 피치(ｐ=25,35,50 nm) 변화, 노즐출구와 전열면간 거이(H/B=1~14) 및 노즐출구유속(ｕ$_{e}$=12.30~ 18.07m/s)의 변화에 따른 전열특성을 실험적으로 구명하고 평판전열면의 경우와 비교 검토한다. 또한 스모크와이어(smoke-wire)법으로 평판 및 리브판에서의 유체의 거동 을 가시화하여 전열기구의 정성적 특성을 검토하는데 목적이 있다.

• 한국추진공학회지
• /
• 제3권4호
• /
• pp.44-50
• /
• 1999

Unlike impinging Quadlet injector(OOOF type)에 대한 혼합효율, 혼합특성속도, 혼합특성속도효율을 연소성능을 예측하기 위해 비연소 실험을 통하여 구하였다. 모의 추진제는 물($H_2$O)와 케로신($CH_{1.97}$)을 사용하였고, 혼합상관인자로써 산화제, 연료 분류의 운동량비를 사용하였다. 인젝터 분무특성을 파악하기 위해 오리피스(orifice) 각 hole에 대한 유량계수, 분무형상, 질량분포 획득이 수행되어졌다. 연구 결과, 침투깊이는 혼합효율, 혼합특성속도, 혼합특성속도 효율에 영향을 미침을 알 수 있었다. 또한, 혼합효율 및 혼합특성속도 효율은 MR=1.67(TMR=2.5)에서 87%로 최대값을 가지며 산화제 과잉상태보다 연료 과잉상태에서 더 큰 감소율을 보였다.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.734-743
• /
• 1999

The local Nusselt numbers have been measured for a round turbulent jet impinging on the concave surface with and without rib. Liquid crystal/transient method was used to determine the Nusselt number distributions along the surface. The temperature on the surface was measured using liquid crystal and a digital color image processing system. The experiments were made for the jet Reynolds number (Re) 23,000, the dimensionless nozzle-to-surface distance (L/d) from 4 to 10, the dimensionless surface curvature (d/D) 0.056, and the rib type (height ($d_1$) 0.2 cm, pitch (p) from 1.2 to 3.2 cm). It was founded that only when $L/d{\geq}6$, the average Nusselt numbers on the concave surface with rib are higher than those without rib, mainly due to an increase in the turbulent intensity caused by the effect of rib attached to the wall surface. It was realized that the rib attached to the concave surface may no longer enhance the heat transfer rate or even lowers it depending on the rib type and flow conditions. In addition, the results by the steady-state method using the gold-film Intrex were in good agreement with those by the transient shroud method.

• 대한기계학회논문집B
• /
• 제24권5호
• /
• pp.718-724
• /
• 2000

A model for depicting the rocket engine combustion process is presented and several experiments near a design point are provided with a FOOF type of unlike impinging injector for a propellant combination of Jet A-1 fuel and liquid-oxygen. The model is based on the assumption that the vaporization is the rate-controlling combustion process. The effects of initial drop size and initial drop velocity are systematically shown and discussed. It is seen that in the midst of considered parameters the change of initial drop size is more sensitive to the performance. The proposed model describes qualitative trends of combustion process well despite of its simplicity.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2000년도 제15회 학술강연회논문초록집
• /
• pp.5-5
• /
• 2000

이 연구의 목적은 한국항공우주연구소가 개발 중인 액체추진제 로켓엔진의 축소형 엔진에 대하여 인젝터 배열의 변화가 성능 및 연소특성에 미치는 영향을 분석하는데 있다. 인젝터의 배열방식에 따라 방사형(radial) 및 직교형(H-type) 인젝터를 연구대상으로 하였으며 충돌각의 변화에 2차원 및 3차원 해석을 수행하였다. 로켓엔진에는 스월러 인젝터를 고려하지 않았기 때문에 인젝터의 배열 및 충돌 각은 엔진성능뿐만 아니라 연소특성에도 중요하게 영향을 미치는 인자가 된다.(중략)