• 한국지반환경공학회 논문집
• /
• 제24권1호
• /
• pp.25-36
• /
• 2023

국내 낙석, 토사 붕괴 등의 피해를 방지하기 위해 설치하는 것은 낙석 방지책이다. 이 중 낙석 방지울타리는 50kJ의 낙석 운동에너지에 설계가 되고 있다. 낙석 운동에너지의 경우, 발생하는 사면의 형태에 따라 크게 달라지며 기존의 연구로는 ETAG 27을 이용한 100kJ급 낙석 충돌에너지에 대한 울타리 성능평가를 실시하였다. 하지만 기존의 연구들은 낙석 방지울타리가 신규로 설치되는 것을 대상으로 하였다. 본 연구에서는 수치해석을 통해 신규 설치가 아닌 기존의 낙석 방지울타리에 보강부재를 설치하고, 120kJ의 낙석 운동에너지에 대해 방어할 수 있는 고강도 낙석 방지울타리의 구조 성능을 평가하였다.

• Computers and Concrete
• /
• 제9권1호
• /
• pp.21-33
• /
• 2012

This paper presents the numerical simulation of the rigid 12.6 mm diameter kinetic energy ogive-nosed projectile impact on plain and fiber reinforced concrete (FRC) targets with compressive strengths from 45 to 235 MPa, using a three-dimensional finite element code LS-DYNA. A combined dynamic constitutive model, describing the compressive and tensile damage of concrete, is implemented. A modified Johnson_Holmquist_Cook (MJHC) constitutive relationship and damage model are incorporated to simulate the concrete behavior under compression. A tensile damage model is added to the MJHC model to analyze the dynamic fracture behavior of concrete in tension, due to blast loading. As a consequence, the impact damage in targets made of plain and fiber reinforced concrete with same matrix material under same impact velocities (650 m/s) are obtained. Moreover, the damage distribution of concrete after penetration is procured to compare with the experimental results. Numerical simulations provide a reasonable prediction on concrete damage in both compression and tension.

• Wind and Structures
• /
• 제13권2호
• /
• pp.95-108
• /
• 2010

This review paper discusses research from the last few years relating to windborne debris risk models and the essential elements of engineering damage prediction models. Generic types of windborne debris are discussed. The results of studies of debris trajectories that are relevant to damage models are described - in particular the horizontal component of debris velocity as a function of distance travelled. The merits of impact momentum versus impact kinetic energy as a relevant parameter for predicting damage are considered, and how published data from generic cannon Impact tests can be used in risk models. The quantitative variation of debris impact damage with wind speed is also discussed. Finally the main elements of previously-proposed debris damage models are described.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.84-87
• /
• 2000

Square tubes used for vehicle structure components have an important role on keeping its stiffness and preserving occupant safety in vehicle collision and rollover in which it experience axial collapse, bending collapse or both. Bending collapse, which absorbs kinetic energy of the impact and retains a survival space for the occupant, is a dominant failure mode in oblique collision and rollover. Thus, in this paper, the bending collapse characteristics such as the maximum bending moment and energy absorption capacity of the square tube replaced by light-weight material were evaluated and presented. The bending test of cantilever tubes which were fabricated with aluminum, GFRP and aluminum/ GFRP hybrid by co-curing process was performed. Then the maximum bending moment and the energy absorption capacity from the moment-angle curve were evaluated. Based on the test results, it was found that aluminum/ GFRP hybrid tube can show better specific energy absorption capacity compared to the pure aluminum or GFRP tube and can convert unstable collapse mode which may occur in pure GFRP tube to stable collapse mode like a aluminum tube in which plastic hinge is developed.

• 한국운동역학회지
• /
• 제17권1호
• /
• pp.91-97
• /
• 2007

The purpose of this study was to investigate the changes of various balls velocity under the different surface conditions after impact. For this study, four different balls were used which are golf ball, tang-tang ball, table tennis ball, and iron ball. And two different types of ground conditions were used which are artificial grass green and glass green. Movements of putter head and ball were recorded with 2 HD video cameras(60 Hz, 1/500s shutter speed). Small size control object($18.5cm{\times}18.5cm{\times}78.5cm$) was used in this study. To transfer the same amount of kinetic energy to the ball, pendulum putting machine was used. Analyzing the process of impact and the ball movement, a putter was digitized the whole movement but the ball was digizited within the 50cm movement. Velocities were calculated by the first central difference method(Hamill & Knutzen, 1995). Putter head velocities were about 112.2cm/s-116.2cm/s at impact. Maximum ball velocities were appeared 0.08s-0.10s after impact no matter what the ground conditions are. Table tennis ball recorded higher ball velocities than the other ball velocities and iron ball recorded the lowest ball velocity in this group. But Table tennis ball was influenced with the frictional force and immediately was decreased at the artificial grass green condition. If an object is received the kinetic energy under the static condition(v=0cm/s), the object recorded the maximum velocity shortly after the impact and then decreased the velocity because of the frictional force. The ball distance from the start position to the peak velocity position is about 6cm-10cm under the 112.2cm/s-116.2cm/s putting velocity with putter. 0.25 seconds later after impact balls were placed 40cm distance from the original position except iron ball. In this study, ball moving distances were too short therefore it was not possible to investigate the reactions after the translational force is disappeared. Rotational force would play a major role at the end of the ball movement. Future study must accept two things. One is long distance movement of ball and the other is balanced ground. Three-piece ball is a good item to investigate the golf ball movement on the different surface conditions.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.311-314
• /
• 2007

The experimental method of measuring dynamic properties of structures was presented. The method is based on the flexural wave propagation characteristics. Using the method, change in structural dynamic properties due to damage is measured. The crack has much more significant impact on the strain energy than the inertial effects. From this, the sensitivity of the dynamic stiffness on the crack location is estimated by calculating the strain energy. When the wave propagates, the strain and kinetic energies shows cyclic changed over space. The crack that occurred at locations where the wave energy is in the form of the potential energy affected most significantly the wave propagation characteristics. The effects of crack location on the wave propagation were used to determine the crack location.

• ETRI Journal
• /
• 제39권2호
• /
• pp.284-291
• /
• 2017

Drain-induced barrier lowering (DIBL) is one of the main parameters employed to indicate the short-channel effect for nano metal-oxide semiconductor field-effect transistors (MOSFETs). We propose a new physical model of the DIBL effect under two-dimensional approximations based on the energy-conservation equation for channel electrons in FETs, which is different from the former field-penetration model. The DIBL is caused by lowering of the effective potential barrier height seen by the channel electrons because a lateral channel electric field results in an increase in the average kinetic energy of the channel electrons. The channel length, temperature, and doping concentration-dependent DIBL effects predicted by the proposed physical model agree well with the experimental data and simulation results reported in Nature and other journals.

• 한국철도학회논문집
• /
• 제4권3호
• /
• pp.94-101
• /
• 2001

One of the best methods to evaluate crashworthiness of a full rake trainset is to analyse 1-dimensional dynamic model using dampers, nonlinear springs and bars, and masses. In this study, the crashworthiness of KHST has been evaluated by analysing a nonlinear dynamic model made up of springs/bars-dampers-masses. The numerical results show that the KHST can absorb more kinetic energy at lower impact forces and lower accelerations in case of heavy collisions, if compared with KTX. Also, the KHST can be protected from any damage in its car-body and electric components except the energy absorbing tube in case of light collisions, like train-to-train accidents at speed under 8 kph. On the other hand, the KTX may be more damaged in the light collisions because there is no energy absorbing tube.

• 한국표면공학회지
• /
• 제57권2호
• /
• pp.105-114
• /
• 2024

Tempering behavior and mechanical properties in AISI H13 steel, quenched and tempered from 300 ℃ to 700 ℃ for different tempering time (1, 2, 5, 10, 20 hr) were quantitatively investigated by scanning electron microscopy (SEM), x-ray diffractometer (XRD), impact test machine, rockwell apparatus, ball-on-disk tester. Under the condition that the tempering time is 2 hours, the hardness increases slightly as the tempering temperature increases, but decreases rapidly when the tempering temperature exceeds 500 ℃, while the impact energy increases in proportion to the tempering temperature. Friction tests were conducted in dry condition with a load of 30 N, and the friction coefficient and wear rate according to tempering conditions were measured to prove the correlation with hardness and microstructure. In addition, primary tempering from 300 ℃ to 700 ℃ was performed at various times to establish a kinetic model to predict hardness under specific tempering conditions.

• Structural Engineering and Mechanics
• /
• 제78권1호
• /
• pp.31-39
• /
• 2021

To investigate numerically the effect of all parameters on the outcome of an aircraft impact into robust engineering structures like nuclear power plant containments is a tedious task. In order to reduce the problem to a manageable size, we propose a single dimensionless parameter, the damage potential, to characterize the main features of the impact. The damage potential, which is the ratio of the initial kinetic energy of the aircraft to the work required to crush it, enables us to find the crucial parameter settings that need to be modelled numerically in detail. We show in this paper that the damage potential is indeed the most important parameter of the impact that determines the time-dependent reaction force when either finite element (FE) modelling or the Riera model is applied. We find that parameters that do not alter the damage potential, like elasticity of the target, are of secondary importance and if parameters are altered in a way that the damage potential remains the same then the course of the impact remains similar. We show, however, that the maximum value of the reaction force can be higher in case of elastic targets than in case of rigid targets due to the vibration of the target. The difference between the Riera and FE model results is also found to depend on the damage potential.