• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.659-673
• /
• 2021

This study aims to investigate the impact of the High Pressure Selective Catalytic Reduction system (SCR-HP) on a large marine two-stroke engine performance parameters by employing thermodynamic modelling. A coupled model of the zero-dimensional type is extended to incorporate the modelling of the SCR-HP components and the Control Bypass Valve (CBV) block. This model is employed to simulate several scenarios representing the engine operation at both healthy and degraded conditions considering the compressor fouling and the SCR reactor clogging. The derived results are analysed to quantify the impact of the SCR-HP on the investigated engine performance. The SCR system pressure drop and the cylinder bypass valve flow cause an increase of the engine Specific Fuel Oil Consumption (SFOC) in the range 0.3-2.77 g/kWh. The thermal inertia of the SCR-HP is mainly attributed to the SCR reactor, which causes a delayed turbocharger response. These effects are more pronounced at low engine loads. This study supports the better understanding of the operating characteristics of marine two-stroke diesel engines equipped with the SCR-HP and quantification of the impact of the components degradation on the engine performance.

• Journal of East Asia Management
• /
• v.3 no.2
• /
• pp.1-19
• /
• 2022

This study suggests an integrated theoretical framework for the relationship between political risk and multinational corporation (MNC) subsidiary's performance in the emerging market. The political risk would have a negative impact on MNC subsidiary's performance in the emerging countries that are developing in Asia, the Commonwealth of Independent States, Africa, and South America. The major reason is that political risks could generate a loss of benefit or a loss of control for MNC's subsidiary. In this study, I suggest that corporate social responsibility (CSR) strategy would be a solution to overcome various political risks. Specifically, the affiliated firms with diversified industries or greater financial resources could mitigate the negative impact of political risk than unaffiliated firms. Because they can use their tangible or nontangible asset such as information, technology, and construction in order to gain legitimacy and trust from local government, local community, and local firms in the emerging market. Finally, I claimed the costs of the affiliated firms would exceed the benefits at the initial stages, while the benefits of affiliated firms would exceed the costs over time when political risks become higher. The reason is that the trust gained from local stakeholders accumulates over time and the impact of CSR strategy would become an important solution to overcome the risks in and unstable context.

• Journal of the Korea Safety Management & Science
• /
• v.26 no.2
• /
• pp.107-115
• /
• 2024

This study conducted frequency analysis, reliability analysis, descriptive statistics, and correlation analysis to determine the impact of quality control managers' perception and implementation of KS certification factory inspection evaluation items on follow-up management. Through a multiple linear regression model, the influence of KS certification officer's awareness and implementation of KS certification factory inspection on post management was found to have a positive (+) influence on post management, with implementation having a greater influence on post management than awareness. It was having an impact. The independent variable (perception) has a statistically significant impact on the mediating variable (execution), and in the stage of verifying the mediating effect, the influence of the independent variable (perception) on the dependent variable (follow-up management) has a statistically significant impact. , In the stage where the independent variable (perception) and the mediator (implementation) are input simultaneously, both the independent variable and the mediator have a statistically significant effect on the dependent variable, indicating that there is a mediation effect.

• Korean Journal of Ecology and Environment
• /
• v.54 no.4
• /
• pp.334-345
• /
• 2021

The present study investigated the effect of global warming on germination and initial growth across six deciduous oak species (Quercus mongolica, Q. variabilis, Q. serrata, Q. dentata, Q. aliena, and Q. acutissima), which are the dominant tree species in Korea forest ecosystems. Seeds were sown in climate change treatments, with temperatures higher than those of the control (approximately 3.0℃ higher), and CO₂ concentrations higher than those of the control (approximately 2-fold higher). Initial growth in each species was measured every two weeks. Initial growth was more rapid in all oak species at the time of root and shoot emergence under high temperature and CO₂ treatments than in the control group. Leaf emergence in Q. mongolica, Q. variabilis, and Q. serrata occurred earlier under the climate change treatments than under the control. Root length increased significantly in Q. mongolica, Q. variabilis, and Q. dentata under the climate change treatments when compared to under the control. However, Q. aliena and Q. serrata exhibited a contrasting trends, and no significant difference was observed between the species and Q. acutissima. Shoot length increased significantly in Q. aliena under climate change treatments when compared to under the control but decreased in Q. aliena. In addition, no significant difference was observed in shoot length among Q. mongolica, Q. dentata, and Q. acutissima. The results showed that climate change treatments facilitated early growth, rapid emergence from the ground, leaf development, and enhanced belowground growth in Q. mongolica. Conversely, Q. aliena exhibited the lowest aboveground and belowground growth under climate change treatments when compared to other oak species. Climate change treatments had the least impact on Q. acutissima considering the insignificant differences observed in initial growth rates under climate change treatment.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.6
• /
• pp.693-700
• /
• 2012

In this study, the Charpy impact test along with metallurgical observation was conducted to evaluate low temperature impact toughness of structural steel welds with different welding processes to find out the optimal welding process to guarantee the required impact toughness at low temperatures. The welding processes employed are shield metal arc welding (SMAW) and flux cored arc welding(FCAW), which are commonly used welding methods in construction. The Charpy impact test is a commercial quality control test for steels and other alloys used in the construction of metallic structures. The test allows the material properties for service conditions to be determined experimentally in a simple manner with a very low cost. To investigate the impact toughness at low temperatures of the steel welds, specimens were extracted from the weld metal and the heat affected zone. Standard V-notch Charpy specimens were prepared and tested under dynamic loading condition. The low temperature impact performance was evaluated based on the correlation between the absorbed energy and the microstructure. Analysis of the results showed that the optimal welding process to ensure the higher low temperature impact toughness of the HAZ and the weld metal is SMAW process using the welding consumable for steels targeted to low temperature use.

• Composites Research
• /
• v.33 no.5
• /
• pp.235-240
• /
• 2020

In this study, in order to improve the impact resistance of the B₄C tile-inserted B₄C_p/Al7075 hybrid composite, a control method of the B₄C/Al7075 interface was developed and the characteristics of the controlled interface were analyzed. B₂O₃, Ni, and Si were coated on the B₄C tile surface using additional thermal oxidation, electroless plating, and plasma spraying. The coated B₄C tile is inserted into the B₄C_p/Al7075 composite material using the liquid pressurization method. Interfacial energy, bonding strength, and impact resistance were measured to analyze the effect of the coating. All coatings enhanced interfacial energy, bonding strength, and impact resistance, and in particular, it was confirmed that the impact resistance increased by 86.8% when B₂O₃ coating was used. This study is significant in developing and analyzing a core surface treatment method that improves the performance of B₄C/Al series composites, which are attracting attention as next-generation lightweight amour and bulletproof materials.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.22 no.6
• /
• pp.774-779
• /
• 2012

Brain-computer interface based on motor imagery is a system that transforms a subject's intention into a control signal by classifying EEG signals obtained from the imagination of movement of a subject's limbs. For the new paradigm, we do not know which positions are activated or not. A simple approach is to use as many channels as possible. The problem is that using many channels causes other problems. When applying a common spatial pattern (CSP), which is an EEG extraction method, many channels cause an overfit problem, in addition there is difficulty using this technique for medical analysis. To overcome these problems, we suggest a binary particle swarm optimization with channel impact factor in order to select channels close to the most important channels as channel selection method. This paper examines whether or not channel impact factor can improve accuracy by Support Vector Machine(SVM).

• Journal of Environmental Impact Assessment
• /
• v.28 no.5
• /
• pp.483-491
• /
• 2019

In orderto cope with the post-2020 in accordance with the Paris Agreement, greenhouse gas (GHG)reduction in Environmental Impact Assessment (EIA) and its contributions to post-2020 were discussed. The 26 Environmental Impact Statement (EIS) administered by Geum-River Basin Environmental Office from 2010 to 2019 were analyzed for reviewing GHG mitigation measures. From the case study, it was found that the assessment of GHG emissions reduction and climate change adaptation were not appropriately performed. In this study, the following measures are proposed to improve the inappropriate assessment of 'GHG subject matter' associated with EIA according to post-2020, 1) allotment of enforced charge on GHG emission during the EIA process, 2) addition of the 'GHG subject matter' in 'establishing permissible discharge standards' which is based on "Act on the Integrated Control of Pollutant-discharging Facilities", and 3) the participation of stakeholders in early EIA stage for governance. Also the details on the EIA for the preparedness of post-2020 were discussed here.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.47 no.2
• /
• pp.311-322
• /
• 2023

In this study, the properties of various material combinations were evaluated and an ideal material for fabricating protection pads for women's army combat uniforms was determined. Eight specimens were used for the evaluation: two types of materials, namely thermoplastic polyurethane for 3D printing, T and ethylene-vinyl acetate, E; two infill densities, namely 10%, 10 and 30%, 30; two types of pad designs, i.e., without holes, A and with holes, B; 2×2×2=8 and control E. The tensile strength, flexural strength, impact absorption, and weight of these specimens were evaluated. Results revealed that E was the most flexible material; however, its tensile strength and impact absorption were very low. Protection pads made from T (T-10A, T-10B, T-30A, and T-30B) had excellent tensile strength and impact absorption; however, they had low performance in ease of movement. Alternatively, protection pad with holes and an infill density of 30% produced using a combination of T and E had a high initial tensile modulus and exhibited excellent impact absorption. Moreover, it was flexible and light, which satisfies the standards and conditions required by protection pads. However, if T-E-10A and T-E-30B exhibited low impact absorption, as required, they can be regarded as appropriate materials for protection pads.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.6
• /
• pp.1122-1127
• /
• 2001

This paper proposed a speed adaptive control system with load torque observer and feed-forward compensation using neural network for air compressor system driven an induction motor. The motor receive impact load change under the influence of piston movement of up and down, and so it difficult to obtain good speed control characteristics. With real-time adjusting control gain estimated in neural network, control characteristics of motor is improved. The validity of the proposed system is confirmed through the theoretical analysis and computer simulation.