• Journal of Power System Engineering
• /
• v.10 no.1
• /
• pp.19-24
• /
• 2006

This work treats a controlled auto-ignition (CAI) single cylinder gasoline engine, focusing on the extension of operating conditions. The fuel was injected indirectly into electrically heated inlet air flow. In order to keep a homogeneous air-fuel mixing, the fuel injector was water-cooled by a specially designed coolant passage. The engine performance and emission characteristics were investigated under the wide range of operating conditions such as 40 in the air-fuel ratio, 1000 to 1800 rpm in the engine speed, 150 to $180^{\circ}C$ in the inlet-air temperature, and $60^{\circ}$ BTDC in the injection timing. The ultra lean-burn with self-ignition of gasoline fuel by heating inlet air was achieved in a controlled auto-ignition gasoline engine. It could be also achieved that the emission concentrations of carbon monoxide, hydrocarbons and nitrogen oxide significantly reduced by CAI combustion compared with conventional spark ignition engines.

• Journal of Biosystems Engineering
• /
• v.12 no.1
• /
• pp.45-52
• /
• 1987

In order to improve the thermal efficiency of an internal combustion engine, various ignition timing control systems were examined and the best one was chosen. The parts used for the systems were a microcomputer system with DAS, 8 bit output port (D-FLIP FLOP), three types of isolation circuit, two types of ignition timing pulse generator, three types of switching circuit and two types of high voltage ignition circuit. Most systems did not operate well due to the effects of electromagnetic waves and surge currents occurring when the ignition began or ended with resulting high voltage. The best ignition timing control system was found to be the combination of (microcomputer system)-(ignition timing pulse generator using step motor position control pick-up)-(switching circuit using TR logic)-(high voltage ignition circuit using CDI).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.2
• /
• pp.147-157
• /
• 1996

Natural gas is gaining more attraction as a future fuel in particular both for environmental protection and energy conservation. In order to bring about more widespread use of gaseous engines, the technology capable of achieving output and efficiency performance equivalent to that of diesel engines needs to be developed. In the present paper, the requirements of the pilot torch from pre-chamber for ensuring ignition and promoting combustion are discussed by means of taking high-speed flame photography and system can run with leaner mixture of various fuels comparing to the electric plug ignition system cause the ignition delay period ignited with the torch and the combustion period are very short in spite of changing A/F of gaseous fuels in the main chamber. However, the suitable piston-cavity design for the use of lower-hydrocarbon fuels such as propane and butane must be discussed increasingly in the mear future.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.1-6
• /
• 2014

The more or less homogeneous fuel-air mixture that exists at the end of the compression process is ignited by an electric ignition spark from a spark plug shortly before top dead center. The actual moment of ignition is an optimization parameter; it is adapted to the engine operation so that an optimum combustion process is obtained. Brake mean effective pressure (BMEP) of the spark ignition energy control device (IECD) than conventional spark system at the stoichiometric mixture is increased about 9%. For lean burn engine, the lean limit is extended about 25% by using the IECD. It was considered the stability of combustion by the increase of flame kernel according to the high ignition energy supplies in initial period and discharge energy period lengthen by using the IECD.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.37-40
• /
• 2013

Hydrogen-dimethy ether (DME) and hydrogen-diesel compression ignition engine combustion were investigated and compared each other in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME and diesel were injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME and diesel inejction timing was varied to find the optimum CI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. Fuel consumption, heat release rate, and exhaust emissions were measured to analyze each combustion characteristics of each ignition promoter. Fuel consumption was decreased when diesel was used as an ignition promoter. This is due to the lower volatility of diesel which created more stratified charge than DME.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.3
• /
• pp.303-307
• /
• 2001

The ignition of propane was investigated behind reflected shock waves in the temperature range of 1350-1800 K and the pressure range of 0.75-1.57 bar. The ignition delay time was measured from the increase of pressure and OH emission in the C3H8-O2-Ar system. The relationship between the ignition delay time and the concentrations of propane and oxygen was determined in the form of mass-action expression with an Arrhenius temperature dependence. The numerical calculations were also performed to elucidate the important steps in the reaction scheme of propane ignition using various reaction mechanisms. The ignition delay times calculated from the mechanism of Sung et al.1 were in good agreement with the observed ones.

• Journal of the Korean Society of Safety
• /
• v.20 no.3 s.71
• /
• pp.98-104
• /
• 2005

This study experimentally and theoretically examines the fire characteristics of 100- by 100- by 50-mm samples of flame retardant treated Douglas fir. Samples were exposed to a range of incident heat fluxes 10 to $50kW/m^2$. The time to ignition measurements obtained from the cone heater were used to derive characteristic properties of the materials. A one-dimensional integral model has been used to predict the, time to ignition, critical heat flux and ignition temperature of samples. Ignition data and best-fit curves confirm ${{\dot{q}}_i}^{'}{\rightarrow}{{\dot{q}}_{cr}^{'}\;then\;t_{ig}{\rightarrow}{\infty}$ and when ${{\dot{q}}_i}^'{\gg}{{\dot{q}}_{cr}^'\;then\;t_{ig}{\rightarrow}0$. And Ignition of flame retardant treated samples occurred not at incident heat flux of bellow $10kW/m^2.$. By a one-dimensional integral model, the critical heat flux of each samples was predicted $10.21kW/m^2,\;11.82kW/m^2,\;and\;14.16kW/m^2$ for the D-N, D-F2, and D-F4, respectively. In ignition temperature of each samples, flame retardant treated samples were measured high about $50^{\circ}C$ than non-treated samples. Water-soluble flame retardant used in this study finds out more effect in delay of time to ignition when incident heat flux is low than high.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.3
• /
• pp.75-82
• /
• 2004

The allowable exhaust standard has been intensified as a part of the countermeasure to decrease air pollution in the world. As the cars with an alternative fuel starts to get into the spotlight, the cars with low emission has been introduced and exhaust gas regulation forced in this country. These days, LPG vehicles, which infrastructure of fuel was already built up, and CNG vehicles are recognized for alternative fuel cars in this country. In this study, the constant volume combustion chamber was manufactured and used for experiments to obtain the ignition characteristics of LPG fuel and the optimal ignition energy. The experiment measured the combustion characteristics, in regard to the change of combustion variable, and the change of ignition energy. During the combustion of fuel, the maximum temperature inside the combustion chamber is higher when the initial pressure is higher. The burning velocity also seems to have the same characteristic as the temperature. However, the heat flux did not change much with the theoretical correct mixture but the various initial temperature of the combustion chamber. The heat flux got faster and ignition energy bigger as the dwell time of the ignition system expanded. When the dwell time get longer, the ignition energy also increased then fixed. The ignition energy increased as the initial pressure inside the combustion chamber higher. The heat flux got faster as the dwell time expanded.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.2
• /
• pp.12-20
• /
• 2000

The numerical analysis, including chemical reaction of an entire ramjet engine is studied to understand the ignition transient mechanism and the dynamic characteristics of the Integrated Rocket Ramjet System comprehensively. Details of how a subsonic combustion environment is established from the supersonic ram air after removal of the inlet port cover, are examined during the ignition transient. Various physical processes are investigated systemically, including ignition, flame propagation, flame dynamics, and vorticity evolution.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.4
• /
• pp.238-243
• /
• 2006

This paper presents novel ignition method for automotive 35W metal halide discharge lamp electronic ballast. At this study, the novel method of ignition is developed to reduce costs and size of the ballast. By use of the novel method, the voltage needed in ignition is decreased, which result in use of the lower voltage rating power devices compared with conventional method and product compactness was achieved by deleting a circuit generating negative voltage needed in ignition at an conventional circuit. In terms of luminosity, color rendering, light efficiency(lm/W) and lifespan, the metal halide lamp is superior to, but unlike halogen lamp, it have more complicated transient characteristics to reach its steady state than the conventional halogen lamp. Therefore, in this paper, the electronic ballast was designed such that the metal halide lamp could be optimized for the automotive, by applying a method of microcontroller-based digital control. The results of the proposed system is verified through various experiment results.