• Journal of Hydrogen and New Energy
• /
• v.27 no.4
• /
• pp.357-364
• /
• 2016

Recently, the world faces the environmental problem such as air pollution due to harmful gas discharged from car and abnormal climate due to the green-house gases increased by the discharge of $CO_2$. Compressed Natural Gas (CNG), one of alternative for this problem, is less harmful, compared to the existing fossil fuel, as gaseous fuel, and less carbon in fuel ingredients and carbon dioxide generation rate relatively favorable more than the existing fuel. However, CNG fuel has the weakness of slow flame propagation speed and difficult fast burn. On the other hand, hydrogen does not include carbon in fuel ingredients, and does not discharge harmful gas such as CO and HC. Moreover, it has strength of quick burning velocity and ignition is possible with small ignition energy source and it's has wide Lean Flammability Limit. If using this hydrogen with CNG fuel, the characteristics of output and discharge gas is improved by the mixer's burning velocity improved, and, at the same time, is possible to have stable lean combustion with the reduction of $CO_2$ expected. Therefore, this research tries to identify the characteristics of engine and emission gas when mixing CNG fuel and hydrogen in each portion and burning them in spark igniting engine, and grasp the combustion stability and emission gas characteristics according and use it as the basic data of hydrogen-CNG premixed engine.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.5
• /
• pp.1052-1058
• /
• 2005

This paper dealt with the design and fabrication of a low frequency electronic ballast for ruh attracting lamps. The proposed electronic ballast was composed of a full-wave rectifier, a step don converter operated as a constant power controled current source, an inverter operated by 130 Hz square wave, and an ignition circuit. An acoustic resonance phenomenon of discharge lamps could be eliminated by application of 130 Hz square wave. Also, a circuit of high voltage pulse generation for lamp ignition was added to the ballast. From the experimental results, voltage and current of the lamp operated by the electronic ballast were estimated 132.5 V and 7.6 A, respectively. and the power consumption was about 1,000 W. The weight of the ballast, which is one of important advantages, was reduced to one-fifth of conventional magnetic ballasts.

• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.92-97
• /
• 2010

A study is conducted on thermal characteristics of biodiesel which is already being produced in many countries because of its stable supply of energy in non oil-producing countries and economical benefits against increasing oil price, and environment conservation. So biodiesel has been used as important energy source in the fuel fields and a mount of production has increased year by year. Therefore, it is very important to find out the thermal characteristics of biodiesel for ignition temperature, maximum pressure and thermal behavior. The purpose of this study is to compare on thermal characteristics of biodiesel, petroleum diesel and those mixtures. Also, the main study was performed by flash point testers and modified closed type of pressure vessel test (MCPVT). Based on the data of flash point and MCPVT, the ignition temperature and the maximum pressure of biodiesel was $182^{\circ}C$ and 40.1bar, and petroleum diesel was $54^{\circ}C$ and 29.8bar.

• Journal of the Korean Institute of Gas
• /
• v.15 no.2
• /
• pp.82-87
• /
• 2011

Heat transfer oils are used in applications such as heating systems of chemical plant, refinery heat exchange systems, gas plant process, injection molding systems, and pulp and paper processing. These oils are extremely stable and resistance to thermal and oxidative degradation. In the event of a spill or accidental release of heat transfer oils, it can be ignite easily when there is an ignition source. This paper discusses the flammability and thermal stabilities of new and used oils. The flammability of the oils are assessed by measuring changes in flash point and auto ignition temperature. The thermal stability of oils are evaluated by the thermal screening unit ($TS^u$) and the differential scanning calorimeter (DSC). From the experimental results, it is suggested to give fire hazard characteristics to safe precautions for the proper use and treatment of heat transfer oils.

• Fire Science and Engineering
• /
• v.34 no.2
• /
• pp.14-21
• /
• 2020

This paper presents the study of a fire risk to the backside of two miniatures of ISO 9705 2/5 using a lightweight partition for indoor space division and reproduction of the ISO 9705 test. An SGP partition, stud partition, glass wool panel, urethane foam panel, sandwich panel, and glass partition were selected as the test specimens, which are frequently used in construction. According to the ISO 9705 test standard, stabilization was achieved using a measuring device that recorded data before the ignition of a burner and continued recording for 120 s thereafter. After ignition was achieved, the power was increased to 300 kW for 600 s and then reduced to 100 kW for 600 s. The specimens were subsequently observed for 180 s, and the fire risk to the backside and the fire pattern of the wall unit were analyzed. Owing to the amount of heat generated by the ignition source, the maximum temperature of the backside was observed to be 67.7 ℃ for the SGP partition, 55.1 ℃ for the stud partition, 52.4 ℃ for the glass wool panel, 727.4 ℃ for the sandwich panel, 561 ℃ for the urethane foam panel, and 630.5 ℃ for the glass partition. In the cases of the sandwich and urethane foam panels, the explosion of flammable gas occurred by virtue of fusion of the interior materials. The reinforced glass was fractured owing to the temperature difference between the heat- and nonheat-responsive parts. Ultimately, the fire risk to the nearby section room was deemed to be high.

• Journal of Environmental Science International
• /
• v.9 no.2
• /
• pp.137-144
• /
• 2000

The observations on the seasonal fluctuation and distributional characteristic of organic matters on surface sediments and its origin were carried out at the 25 stations in Keogeum-sudo, southern coast of Korean Peninsula from February to October in 1993. I made an analysis on the environmental factors for surface sediments such as temperature, ignition loss, chemical oxygen demand, pheopigment, total sulphide, water content, mud content in grain size, COD/IL ratio and COD/sulphide ratio. The results are as follows ; 1) The range of temperature on the surface sediments was between 6.2${\circ}C$ and 24.6${\circ}C$. The highest mean temperatuer of mud was 24.0${\circ}C$ in summer, the lowest 6.6${\circ}C$ in winter. 2) Ignition loss(IL) fluctuated between 1.2% in winter and 16.8% in spring, that is to say, the seasons of increasing in temperature were very high ignition loss. 3) Chemical oxygen demand(COD) showed the highest mean value of 20.52 mg/g dry in summer within the range of 15/46~32.78 mg/g dry, while showed the lowest of 5.79 mg/g dry in winter within the range of 7.4~17.39 mg/g dry. 4) Pheopigment concentrations showed the highest mean value of 4.85 $\mu\textrm{g}$/g dry in autumn within the range of 0.84~9.21 $\mu\textrm{g}$/g dry, while it did the lowest mean value of 1.97 $\mu\textrm{g}$/g dry in summer within the range of 0.23~4.83 $\mu\textrm{g}$/g dry. 5) Total sulphide (H2S) fluctuated between no detect(ND) in spring, and 2.43 mg/g dry in sutumn. The highest mean value was 0.68 mg/g dry in sutumn, the lowest was 0.16 mg/g dry in spring. 6) Water content(WC) and mud content in grain size showed the mean value of 43.2% within the range of 26.5~59.7% and 91.0% within the range of 57.8~99.2%, respectively. 7) By the analytical results on the source of organic matter, it had been dumped from the seaweed farms in Keogeum-sudo coastal waters.

• Journal of the Korean Society of Safety
• /
• v.20 no.4 s.72
• /
• pp.171-179
• /
• 2005

It is essential to understand the role of wall lining materials when they are exposed to a fire from an ignition source. Full-scale test methods permit an assessment of the performance of a wall lining material. Fire growth models have been developed due to the costly expense associated with full-scale testing. The models require heat flux maps from the ignition burner flame as input data. Work to date was impeded by a lack of detailed spatial characterization of the heat flux maps due to the use of limited instrumentation. To increase the power of fire modeling, accurate and detailed heat flux maps from the ignition burner are essential. High level spatial resolution for surface temperature can be provided from an infrared camera. The objective of this study was to develop a heat flux mapping procedure for a room test burner flame to a wall configuration with surface temperature information taken from an infrared camera. A prototype experiment was performed using the ISO 9705 test burner to demonstrate the developed heat flux mapping procedure. The results of the experiment allow the heat flux and spatial resolutions of the method to be determined and compared to the methods currently available.

• Journal of the Society of Disaster Information
• /
• v.20 no.1
• /
• pp.47-59
• /
• 2024

Purpose: This study aims to propose measures for the prevention of fire and explosion accidents within manufacturing facilities by improving the existing classification criteria for hazardous locations based on the leakage patterns of flammable liquids. The objective is to suggest ways to safely manage ignition sources and combustible materials. Method: The hazardous locations were calculated using "KS C IEC 60079-10-1," and the calculated explosion hazard distances were visualized in 3D. Additionally, the formula for the atmospheric dispersion of flammable vapors, as outlined in "P-91-2023," was utilized to calculate the dispersion rates within the hazardous locations represented in 3D. Result: Visualization of hazardous locations in 3D enabled the identification of blind spots in the floor plan, facilitating immediate recognition of ignition sources within these areas. Furthermore, when calculating the time taken for the Lower Explosive Limit (LEL) to reach within the volumetric space of the hazardous locations represented in 3D, it was found that the risk level did not correspond identically with the explosion hazard distances. Conclusion: Considering the atmospheric dispersion of flammable liquids, it was concluded that safety management should be conducted. Therefore, a method for calculating the concentration values requiring detection and alert based on realistically achievable ventilation rates within the facility is proposed.

• Fire Science and Engineering
• /
• v.34 no.2
• /
• pp.94-96
• /
• 2020

In November 2013, a case of sustained combustion of a female body was encountered in a Korean farming village. The body was almost completely incinerated from the neck to the knees, and other parts of the body, such as the head, arms, lower legs, and feet, were slightly damaged. The most likely external ignition source was the flame from a matchstick. The elderly woman was found incinerated on the floor of the living room, while other objects in the house were largely undamaged except for having a brown oily or greasy coating. Flammable substances were not detected from the woman's intact pieces of clothing and socks, and her muscular tissues did not contain toxic chemicals. The concentration of carboxyhemoglobin in her peripheral blood was 11% and that of ethyl alcohol in her aqueous humor was below 0.010%. An autopsy failed to determine the exact cause of death because of excessive charring.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.322-326
• /
• 2011

Etch process of silicon dioxide layer by using capacitively coupled plasma (CCP) is currently being used to manufacture semiconductor devices with nano-scale feature size below 50 nm. In typical CCP plasma etcher system, plasmas are generated by applying the RF power on upper electrode and ion bombardment energy is controlled by applying RF power to the bottom electrode with the Si wafer. In this case, however, etch results often drift due to heating of the electrode during etching process. Therefore, controlling the temperature of the upper electrode is required to obtain improvement of etch repeatability. In this work, we report repeatability improvement during the silicon dioxide etching under extreme process conditions with very high RF power and close gap between upper and bottom electrodes. Under this severe etch condition, it is difficult to obtain reproducible oxide etch results due to drifts in etch rate, critical dimension, profile, and selectivity caused by unexpected problems in the upper electrode. It was found that reproducible etch results of silicon dioxide layer could be obtained by controlling temperature of the upper electrode. Methods of controlling the upper electrode and the correlation with etch repeatability will be discussed in detail.