• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.76-86
• /
• 1994

Combustion of diesel engine depends on the mixing of air and evaporating fuel during ignition delay greatly. Variation of air-fuel mixing rate and ignition delay for engine operating condition causes difference of combustion, performance and exhaust emissions. This study is investigated in a turbocharged diesel engine of IDI swirl chamber type. In the results, As injection timing is advanced until $12.6^{\circ}$ BTC, ignition delay decreases. NOx concentration and smoke level in exhaust gas increases for advanced injection timing Ignition delay, combustion period, pressure rise rate and exhaust gas temperature are increased with increasing engine speed. And ignition delay at high load is more decreased than that at low load. Ignition delay and combustion period are decreased with increasing intake pressure. Power increases, temperature and CO, NOx concentration in exhaust gas decreases as intake pressure increases. With increasing load, ignition delay is decreased and combustion period, motoring pressure are increased.

• 한국화재소방학회논문지
• /
• 제33권1호
• /
• pp.7-14
• /
• 2019

우드펠릿은 화력발전소 및 화목 보일러의 연료로 많이 사용되고 있으나 발열량이 높은 우드펠릿을 장기간 보관 시 자연발화의 위험성이 있다. 본 연구에서는 시료 용기의 크기에 따라 유량의 변화에 따른 최소자연발화온도와 발화한계온도를 구하였으며, 발화한계온도를 이용하여 겉보기 활성화 에너지를 측정함으로써 우드펠릿의 발화 특성을 예측하였다. 겉보기 활성화 에너지는 190.224 kJ/mol을 구하였다. 용기에 저장된 시료량이 두꺼워질수록 시료 표면에서 중심까지의 열전달이 어려워 발화유도시간이 긴 것으로 나타났으며, 용기의 크기가 같을 경우 유량의 양이 많아 질수록 자연발화온도는 낮아졌다. 또한 시료용기가 커질수록 자연발화온도는 낮아지고 발화유도시간은 길어지는 것으로 나타났다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제45회 KOSCO SYMPOSIUM 초록집
• /
• pp.111-114
• /
• 2012

The ignition behavior of single coal particles of five kindes of coal with different ranks (low volatile bituminous, low volatile sub-bituminous, high volatile bituminous, lignite) with particle size of $150-200{\mu}m$ was investigated at high heating rate condition. Particles were injected into a laminar flow reactor and the ignition behavior was observed with high speed cinematography. Sub-bituminous were observed to ignite homogeneously; however, low volatile bituminous coal and lignite undergo fragmentation prior to igntion. The observation was analyzed with previous work.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제21회 추계학술대회 논문집
• /
• pp.6-10
• /
• 2003

Accurate description of starting transient history allows and justifies the use of small margin of safety for the engine parts, resulting in high motor mass ratio in addition to satisfying the control and guidance requirements of the vehicle. Studies have been carried out for the prediction and reduction of ignition peak and pressure-rise rate during the starting transient of solid rocket motors. Numerical studies have been carried out using a two dimensional Navier-Stokes solver. It has been inferred through the parametric studies that, in the case of solid rocket motors with uniform port, high ignition peak is observed at high spread rate and low pressure-rise rate. In the case of the port with sudden expansion configuration, high ignition peak is observed at relatively high average spread rate and high-pressure rise rate. These studies are expected to aid the designer in reducing the ignition peak by altering the propellant properties or igniter characteristics without sacrificing the motor performance.

• International Journal of Automotive Technology
• /
• 제5권3호
• /
• pp.195-200
• /
• 2004

This paper is concerned with the Homogeneous Charge Compression Ignition (HCCI) engine as a new concept in engines and a power source for future automotive applications. Essentially a combination of spark ignition and compression ignition engines, the HCCI engine exhibits low NOx and Particulate Matter (PM) emissions as well as high efficiency under part load. The objective of this research is to determine the effects of Exhaust Gas Recirculation (EGR) rate on the combustion processes of HCCI. For this purpose, a 4-cylinder, compression ignition engine was converted into a HCCI engine, and a heating device was installed to raise the temperature of the intake air and also to make it more consistent. In addition, a pressure sensor was inserted into each of the cylinders to investigate the differences in characteristics among the cylinders.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.75-83
• /
• 2001

This paper presents the evaluation of combustion characteristics of sing-hole plasma jet ignitions in comparison with conventional spark ignition for variable of swirl velocity. Plasma jet plugs are three types according to ejecting directions : center of chamber, positive and negative swirl flow direction. Experiments are carried out for equivalent ratio 1.0 of LPG-air mixture in a constant volume cylindrical vessel. Not only the flame propagation is photographed at intervals, but the pressure variation in the combustion chamber is also recorded throughout the entire combustion process. The results show that the plasma jet ignitions and spark ignition enhance the overall combustion rate by increasing the swirl velocity. The dependence of the combustion rate swirl velocity leade to the conclusion that the placma jet plug, which ejects plasma jet to the cwnter of combustion chamber is the most desirable ignitor than other plugs.

• 한국안전학회지
• /
• 제26권1호
• /
• pp.21-26
• /
• 2011

Extinction and ignition characteristics of $CH_4$-air counterflow diffusion flame were numerically investigated using a Flame-Controlling Method(FCM). A skeletal reaction mechanism, which adopts 17 species and 58 reactions, was used in the simulation. The extinction and ignition conditions of the $CH_4$-air diffusion flames were investigated with varying the global strain rate. Upper and middle branches of S-curve for the peak temperature in the inverse of the global strain rate space were obtained with the FCM. The structures of diffusion flames in the upper and middle branches of S-curve were compared. It was found that the global strain rate was not correlated with the local strain rate well in the low global strain rate region. It is expected that the FCM is very useful to obtaining the extinction and ignition condition of diffusion flame, such as fires.

• 한국기계가공학회지
• /
• 제4권1호
• /
• pp.56-62
• /
• 2005

In this study, A controlled auto-ignition (CAI) single cylinder gasoline engine is considered, focusing on the extension of operating conditions. The fuel is injected indirectly into electrically heated inlet air flow. Investigated are the engine performance characteristics under the wide range of operating conditions such as 32 to 63 in the air-fuel ratio, 1000 to 1800 rpm in the engine speed, and 150 to $180^{\circ}C$ in the inlet-air temperature. A controlled auto-ignition gasoline engine which has the super ultra lean-burn with self-ignition of gasoline fuel can be achieved by heating inlet air.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1997년도 제8회 학술강연회논문집
• /
• pp.259-265
• /
• 1997

An analytical study has been peformed to investigate the unsteady ignition characteristics of pulse combustion. In many combustion applications, strain rate of the flow can significantly affect the combustion features; ignition, extinction, and reignition. In the pulse combustion, two jets (hot combustion gases and fresh mixtures) coming from the opposite side of the combustor will collide in the combustor forming a stagnation region where the chemical reaction is suppressed by the strain rate until this becomes below the critical value. In this research, the method of large activation energy asymptotic is adopted with one step irreversible kinetics to examine the ignition response to the periodic variation of the strain rate of flow. The results show the variation of the maximum value of strain rate can determine whether the ignition or extinction occur.

• 한국자동차공학회논문집
• /
• 제17권4호
• /
• pp.93-100
• /
• 2009

Intake/exhaust valve timing and exhaust cam lift were changed to control the internal exhaust gas recirculation (IEGR) and combustion phase of homogeneous charge compression ignition (HCCI) engine. To measure the IEGR rate, in-cylinder gas was sampled during from intake valve close to before ignition start. The lower exhaust cam made shorter valve event than higher exhaust cam and made IEGR increase because of trapping the exhaust gas. IEGR rate was more affected by exhaust valve timing than intake valve timing and increased as exhaust valve timing advanced. In-cylinder pressure was increased near top dead center due to early close of exhaust valve. Ignition timing was more affected by intake valve timing than exhaust valve timing in case of exhaust valve lift 8.4 mm, while ignition timing was affected by both intake and exhaust valve timing in case of exhaust valve 2.5 mm. Burn duration with exhaust valve lift 2.5 mm was longer than other case due to higher IEGR rate. The fuel conversion efficiency with higher exhaust valve lift was higher than that with lower exhaust valve lift. The late exhaust and intake maximum open point (MOP) made the fuel conversion efficiency improve.