• 제목/요약/키워드: Ignition Circuit

검색결과 115건 처리시간 0.04초

마이크로 컴퓨터를 이용(利用)한 엔진점화시기(點火時期) 제어회로(制御回路) (Engine Ignition Timing Control Circuit Using Microcomputer)

  • 민영봉;이기명
    • Journal of Biosystems Engineering
    • /
    • 제12권1호
    • /
    • pp.45-52
    • /
    • 1987
  • 엔진의 점화시기(點火時期)를 제어(制御)하는 데에 마이크로컴퓨터를 이용(利用)하고자 여러 종류(種類)의 제어장치(制御裝置)를 설계(設計) 제작(製作)하여 가동시험한 결과를 요약하면 다음과 같다. 가. 제어장치(制御裝置)의 제작시(製作時) 고압방전(高壓放電)에 의한 잡음(雜音), 서어지, 전자파(電磁波)로부터 디지탈회로와 컴퓨터의 기능(技能)이 교란되는 것을 방지하기 위하여는 고압회로(高壓回路)와 여타 회로와의 분리 및 고압회로의 기생발진 억제와 차폐가 완전하여야 할 것이며, 또한 양질의 점화용(點火用) 도선(導線)을 사용하여야 할 것으로 생각된다. 나. 본 실험의 범위내에서는(컴퓨터시스템) (써어보 기구에 의한 점화신호발생(點火信號發生) 및 제어(制御) - (트랜지스터 스위칭) - (고압회로) 로 구성(構成)시킨 점화시기제어장치가 컴퓨터 등의 기능교란을 일으키지 않고 가장 잘 작동(作動)되었다. 다. 본 실험의 결과(結果)를 기초(基礎)로 마이크로컴퓨터를 이용한 엔진의 최적점화진각제어(最適點火進角制御)에의 응용(應用)이 가능(可能)할 것으로 사료(思料)된다.

  • PDF

점화 신호 종류에 따른 PDE 점화회로의 작동 안정성 연구 (Reviewing of Operating Stability about Pulse Detonation Engine's Ignition Circuit to the Type of Power Sources)

  • 김정민;한형석;오세종;최정열
    • 한국추진공학회지
    • /
    • 제22권6호
    • /
    • pp.11-18
    • /
    • 2018
  • 펄스 데토네이션 엔진 (PDE는) 추진기관으로서 의미 있는 추력을 얻기 위해 100 Hz 이상의 높은 작동 주파수를 요구한다. 따라서 PDE는 높은 작동 주파수에서 정확하게 작동하는 점화 회로 필요로 한다. 이번 논문에서는 교류와 직류 전원을 이용하는 두 종류의 점화 회로를 설계하여 비교하였다. 두 회로는 16.66 에서 100.00 Hz 작동 주파수에서 입력 신호와 변압기의 1 차 코일에 인가되는 전압 변화를 측정하여 시험하였다. 실험 결과 직류 전원의 회로의 경우 증가된 작동 주파수에서 최대 5.15%의 작동 주파수 오차를 보였으나 교류 전원의 회로의 경우 33.33 Hz 이상부터는 거의 맞지 않는 결과를 보였다. 이를 통해 고주파 작동의 PDE에서는 직류 전원의 점화 회로가 선호됨을 확인하였다.

진공차단기 3상 동시 차단시의 서지 특성 분석 (Surge Characteristics Analysis of Three-phase Virtual Chopping at Vacuum Circuit Breaker)

  • 김종겸
    • 전기학회논문지
    • /
    • 제67권9호
    • /
    • pp.1159-1164
    • /
    • 2018
  • Vacuum circuit breakers(VCB) are widely used for current interruption of high-voltage inductive loads such as induction motors. This VCB can be chopped off before the current zero due to its high arc-extinguishing capability. One of the outstanding features of VCB is that it can cut off high frequency re-ignition current more than other circuit breakers. If the transient recovery voltage generated in the arc extinguishing is higher than the dielectric strength of the circuit breaker, a re-ignition phenomenon occurs. The surge voltage of the re-ignition is very high in magnitude and the steepness of the waveform is so severe that it can act as a high electrical stress on the winding. If the high frequency current of one phase affects the other two phases when the re-ignition occurs, it may cause a high surge voltage due to the virtual current chopping. If the magnitude of the voltage allowed in the motor winding is high or the waveform level is too severe, it may lead to insulation breakdown. Therefore, it is necessary to reduce the voltage to within a certain range. In this study, we briefly explain the various phenomena at the time of interruption, analyzed the magnitude of the dielectric strength and the transient recovery voltage at the simultaneous three-phase interruption that can give the greatest influence to the inductive load, proposed a method to reduce the impact.

반파정류를 이용한 형광램프용 전자식 스타터의 개발 (Development of an electronic starter using a half-wave rectifier for fluorescent lamps)

  • 이동호;송상빈;여인선
    • 대한전기학회:학술대회논문집
    • /
    • 대한전기학회 1998년도 하계학술대회 논문집 F
    • /
    • pp.2088-2090
    • /
    • 1998
  • A low-cost electronic starter is developed to decrease ignition failure significantly through successive starting trial and to prevent overheating at the end of fluorescent lamp life. Moreover, it has an additional feature of being capable of ignition at the recovered lamp voltage without any circuit correction. The developed electronic starter is consisted of four parts - a half wave rectifier circuit, a timer circuit, a switching circuit and a protection circuit. The protection circuit made up of a transistor and capacitors utilizing capacitive characteristics, carries out successive starting trial and end-of-life protection. Lamp ignition is completed within 0.5 seconds with taking advantage of a high preheating current from the half-wave rectifier circuit. Nevertheless, its performance is proved to be very excellent through a standard switching endurance test.

  • PDF

감쇠파 고주파전압의 선행방전을 이용한 Plasma jet의 전기적 기동특성에 대한 실험적 연구 (The Experimental Research On The Electrical Characteristics For The Ignition Of Plasma Jet Using The Advance Discharge Of High Frequency Voltage With Attenuation)

  • 전춘생
    • 전기의세계
    • /
    • 제21권4호
    • /
    • pp.27-38
    • /
    • 1972
  • This paper discusses the characteristics about the ignition of D.C. main discharge is a plasma jet generator, manufactured for trial as non-transferred type, when the electrical energy appropriate to the ignition is supplied to the gap between the electrodes by using advance discharge of attenuating high frequency voltage generated by a high frequency oscillator with mercury spark gap. These characteristics are under the influences of (a) the length of mercury gap in high frequency oscillator and the quantity of hydrogen flow supplied to it, (b) the condenser capacity of the high frequency oscillator circuit, (c) the length of plasma jet torch in D.C. main discharge circuit and the quantity of argon flow supplied to it, (d) the circuit constants of D.C. main discharge circuit. The results for these characteristics, obtained by this research, are considered to be helpful to the designs for the ignition of a plasma jet as well as the welding arc stabilizer by high frequency discharge and the high frequency arc welder.

  • PDF

저항회로의 개폐불꽃에 의한 폭발성 가스의 점화한계에 관한 연구 (A Study on The Ignition Limit of Flammable Gases by Discharge Spark of Resistive Circuit)

  • 이춘하
    • 한국가스학회지
    • /
    • 제1권1호
    • /
    • pp.106-112
    • /
    • 1997
  • 본 연구는 직류 저항회로의 개폐불꽃에 의한 폭발성 가스의 점화한계를 실험적으로 고찰하였다. 실험은 IEC형 불꽃점화 시험장치의 폭발용기에 폭발성 가스(메탄-공기 프로판-공기, 에틸렌-공기, 수소-공기)를 각각 넣고 텅스텐 전극과 카드뮴 전극사이에서 발생하는 3,200회의 개폐불꽃에 의한 점화유무를 확인하므로서 점화한계를 구하였다. 또한 실험장치의 점화감도교정을 실험한 후에 실시하므로서 실험의 정확성을 기하였다. 실험결과 최소 점화 전류값을 갖는 최소점화한계농도는 메탄-공기 8.3 [$Vol\%$], 프로판-공기 5.25[$Vol\%$], 에틸렌-공기 7.8[$Vol\%$], 수소-공기 21[$Vol\%$]로서 기존의 실험결과와 유사한 결과를 나타내었다. 또한 최소점화한계농도에서 전압과 최소점화잔류와의 관계를 구한 결과 최소점화한계는 메탄, 프로판, 에틸렌, 수소가스의 순서로 낮아졌고 점화전류의 크기는 전원전압의 크기와 반비례하고, 전극의 과열현상으로 인하여 전압 약 20(V)이하에서는 최소점화전류가 2(A)를 넘으면서 심화한계곡선이 급격히 상승한다는 것 등을 알 수 있었다.

  • PDF

철제펜스로 지지된 동력배선의 단락.지락에 의한 전기화재 발생 개연성 연구 (A Study on the Possibility of Electrical Fires due to the Short Circuit and Ground Fault of Power Cable Supported by an Iron Fence)

  • 김정훈;박병기;송종혁;정기창
    • 한국안전학회지
    • /
    • 제22권6호
    • /
    • pp.41-45
    • /
    • 2007
  • Short circuit and ground fault account for the primary causes of electrical fires. In this research, real-scale experiments were conducted to assess the possibility of electrical fires due to these causes. The experiment conditions were identical with an actual fire accident, in which the power cable was supported by an iron fence. The purposes of this research are to investigate the short circuit caused by wire cutting, the conductivity of the iron fence depending on its coating conditions, and the ground fault of one wire or two wires in an effort to reconstruct the fire accident. The test results show that, owing to the instant operation of circuit breaker in the moment of short circuit or ground fault, the generated ignition energy is far less than necessary to start an ignition. Therefore it is concluded that electrical fire is highly unlikely if the electric system is protected by a circuit breaker with normal functions.

2-단계 HID 램프용 전자식 안정기의 디지털 제어 (Digital Control of Two-Stage Electronic ballast for HID Lamps)

  • 이우철
    • 전력전자학회:학술대회논문집
    • /
    • 전력전자학회 2013년도 추계학술대회 논문집
    • /
    • pp.229-230
    • /
    • 2013
  • The conventional Three-Stage electronic ballast is stable, but Two-Stage electronic ballast has been researching because of efficiency. Three-Stage electronic ballast is consisted of PFC circuit, buck converter, and inverter circuit, but Two-stage is consisted of PFC circuit, Buck-Inverter full bridge circuit. The Buck-Inverter full bridge inverter consists of two half bridge inverters for low frequency switching, and high frequency switching. In the case of street lamp it is far from a lamp to a ballast, the conventional pulsed high voltage ignitor can not turn on the HID lamps because of reduction of ignition voltage. Therefore, it needs to do the research on a resonant ignition to turn on the HID lamps. Therefore, in the Two-Stage electronic ballast which has the resonant tank for ignition, the transient resonant current because of low frequency changing is analyzed, the novel algorithm is proposed to resuce the transient current.

  • PDF

HID 램프용 Two-Stage 전자식 안정기의 과도 전류 제어 (Transient Current Control of Two-Stage Electronics Ballast for HID Lamps)

  • 이우철
    • 조명전기설비학회논문지
    • /
    • 제28권1호
    • /
    • pp.1-8
    • /
    • 2014
  • The conventional Three-Stage electronic ballast is stable, but Two-Stage electronic ballast has been researching because of efficiency. Three-Stage electronic ballast is consisted of PFC circuit, buck converter, and inverter circuit, but Two-stage is consisted of PFC circuit, Buck-Inverter full bridge circuit. The Buck-Inverter full bridge inverter consists of two half bridge inverters for low frequency switching, and high frequency switching. In the case of street lamp it is far from a lamp to a ballast, the conventional pulsed high voltage ignitor can not turn on the HID lamps because of reduction of ignition voltage. Therefore, it needs to do the research on a resonant ignition to turn on the HID lamps. Therefore, in the Two-Stage electronic ballast which has the resonant tank for ignition, the transient resonant current because of low frequency changing is analyzed, the novel algorithm is proposed to resuce the transient current.

분진운의 최소점화에너지에 대한 정전기 방전회로의 매개변수 영향 (Influence of Electrostatic Discharge Circuit Parameters on the Minimum Ignition Energy of Suspended Dust Clouds)

  • 문균태;정재희;미주키 야마구마;최광석
    • 한국안전학회지
    • /
    • 제25권5호
    • /
    • pp.22-26
    • /
    • 2010
  • The ignitability(minimum ignition energy, MIE) of a suspended dust clouds is very important aspect of technical safety indices. This paper reported the experimental results dealing with the influence of discharge circuit on the MIE of a suspended dust clouds. The movement of a suspended dust clouds was also observed with the high speed camera. The Hartmann vertical-tube apparatus(MIKE-3) described in the international standard of IEC and Polypropylene (PP, 50% volume-average, D50: $761{\mu}m$) resin powders were used in this experiment. The following results were obtained: (1) the MIE of a suspended PP powder depended markedly on the discharge circuit; in other words, when a resistor was connected in series with the discharge sparking circuit(RC), the lowest value(31mJ) of MIE was obtained for a suspended PP powder comparison with the other circuits(C circuit; 370mJ or LC circuit; 71mJ). (2) the discharge duration time is more important than other factors with regard to MIE of a suspended PP powder.