• Journal of the Korea Safety Management & Science
• /
• v.19 no.3
• /
• pp.89-95
• /
• 2017

This paper presents another maintenance policy for a group of units under finite operating horizon. A group of identical units are subject to random failures. Group maintenances are performed to all units together at specified intervals, and the failed units during operation are remained idle until the next group maintenance set-up. Unlike the traditional assumption of infinite operating horizon, we adopt the assumption of the finite operating horizon which reflect the rapid industrial advance and short life cycle of modern times. The units are under operation until the end of the operating horizon. Further, the operation of units are extended to the first group maintenance time after the end of the horizon. The total cost under the proposed maintenance policy is derived. The optimal group maintenance interval and the expected number of group maintenances during the horizon are found. It is shown that the proposed policy is better than the classical group maintenance policy in terms of total cost over the operating horizon. Numerical examples are presented for illustrations.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2001-2006
• /
• 2008

The most concerning issue of these days is the energy crisis by increasing threat of dependency on foreign oil and its volatility itself. In the situations, the PHEV is drawing attention for the next generation's car which could give a chance to decrease the dependency on foreign oil. As well as, the Korean electric power infrastructure is a strategic national asset that is under utilized most of the time. With the proper changes in the operational paradigm, it could generate and deliver necessary energy to charge the PHEVs which could penetrate the market within few years. In doing so, it would reduce greenhouse gas emissions, improve the economics of the electricity industry, and reduce the energy dependency. This paper investigate the technical potential and impacts of using the existing idle capacity of the electric infrastructure in conjunction with the emerging PHEVs technology to meet the majority of daily energy needs of the Korean LDV fleet.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1993.06a
• /
• pp.1195-1198
• /
• 1993

We investigate a systematic design procedure of automated rule generation of fuzzy logic based controller for uncertain dynamic systems such as an engine dynamic model.“Automated Tuning”means autonomous clustering or collection of such meaningful transitional relations in the state-space. Optimal control strategies are included in the design procedures, such as minimum squared error, minimum time, minimum energy or combined performance criteria. Fuzzy feedback control systems designed by the cell-state transition method have the properties of closed-loop stability, robustness under parameter variabtions, and a certain degree of optimality. Most of all, the main advantage of the proposed approach is that reliability can be potentially increased even if a large grain of uncertainty is involved within the control system under consideration. A numerical example is shown in which we apply our strategic fuzzy controller design to a highly nonlinear model of engine idle speed contr l.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4B
• /
• pp.186-191
• /
• 2005

To provide fairness among different ONUs in EPON, the upstream channel remains idle for some time after OLT receives the buffer status from all ONUs every cycle, which decreases the utilization and increases the delay. To solve this deficiency, we present a new grant scheduling method. The method consists of dividing ONUs into several sets where OLT can schedule ONUs in one set while others will be transmitting their traffic. This method will better utilize the bandwidth of EPON. The numerical results show that the larger the number of ONU sets is the smaller the minimum overhead becomes.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.348-353
• /
• 2011

By gel-casting, the silicon-polymer green bodies were prepared for silicon nitride ceramics, sintered by microwave gas phase reaction. Considering the viscosity and the idle time of slurries, we decided the operational conditions of related processes, and the optimum concentrations of raw materials powders, organic monomers, cross-linker, dispersant, initiator, and catalyst. So we could get the machinable green bodies, having about 50 MPa of bending strength without cracks by selecting drying conditions carefully.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2019.05a
• /
• pp.86-88
• /
• 2019

In a complex geographical environment, communication quality of communication equipment is being seriously challenged. Secondary Users(SUs) must make the best possible use the idle spectrums that Primary Users(PUs) do not use and change spectrum frequently. Using the relevance vector machine(RVM) to establish a signal noise Ratio(SNR) Model for interference information and bit error rate(BER). Through the model and real-time interference information, the minimum channel SNR meeting the BER requirements of communication equipment can be predicted, and we can also calculate the minimum transmitted power. According to the simulation results, this method has better performance for selecting available channel and restraining interference.

• Journal of Power Electronics
• /
• v.18 no.6
• /
• pp.1627-1633
• /
• 2018

A constant voltage AC-DC converter based on digital assistant technology is proposed in this paper, which has rapid dynamic response capability. The converter operates in the PFM (Pulse Frequency Modulation) mode. According to the load state, the compensation current produced by the digital compensation module was injected into the CS pin to adjust the switching pulse width dynamically and improve the dynamic response. The control chip is implemented based on NEC $1{\mu}m$ 5V/40V HVCMOS process. A 5V/1.2A prototype has been built to verify the proposed control method. When the load jumps from idle to heavy, the undershoot time is only 7.4ms.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.101-108
• /
• 2011

On cold start operation of an SI engine, a catalyst shows poor performance before it reaches activation temperature. Therefore, fast warmup of the catalyst is very crucial to reduce harmful emissions. In this study, an appropriate control strategy is investigated to increase exhaust gas temperature through changes of spark timing. Combustion stability is also considered at the same time. Exhaust gas temperature and pressure of combustion chamber are measured to investigate the effects of spark timings on cold start and idle performance. Experiments showed that retarded spark timing promotes the combustion at the end of expansion stroke and increases exhaust gas temperature during cold start.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.2
• /
• pp.48-57
• /
• 1997

A computer aided analysis and design system is developed for analyzing the driveline torsional vibration of a vehicle. Torsional vibration characteristics of driveline component are investigated and 10 types of module are developed. They can be connected together to represent any driveline configuration. During assembly process simulation program is generated. It is implemented using C++language. A driveline tor- sional vibration system at full load driving condition and idle rattle system are modeled and simulated with this system. Their responses for engine torque excitation are evaluated on time and frequency domain, and the results are compared with test results favorably. This system makes it simpler and easier for design and analysis engineer to model and analyse the driveline system.

• Journal of Korea Multimedia Society
• /
• v.2 no.4
• /
• pp.378-389
• /
• 1999

Parallel tasks in distributed real-time systems can be divided into several subtasks and be executed in parallel according to their real-time attributes. But, it is difficult to gain the optimal solution which is to allocate a tasks deadline into the subtasks deadline while minimizing the subtasks deadline miss. Tn this Paper, we propose the algorithm that allocates deadlines into each subtask, according to the attributes of each subtask(i.e. using communication time and execution time to periodic tasks). Also, we suggest a processor mapping algorithm that considers the communication time among the processors and the effective duplication algorithm which is allocated to the identical processor for the purpose of improving the communication time between the subtasks. We can obtain a result that reduces IPC(Inter-Processor Communication) time and uses the idle processor through applying effective real-time attributes to FUTD(Fully connected, Unbounded Task Duplication) algorithms. As a result, we can improve the average processor utilization.