• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.2
• /
• pp.284-290
• /
• 2014

A fiber-optic beta/gamma dual detector system with two types of sensing probes was fabricated to detect the beta- and gamma-rays simultaneously. As scintillators of the sensing probe type 1, two different inorganic scintillators, $CaF_2(Eu)$ and LYSO(Ce) crystals, were used to obtain the each scintillating efficiency with respect to beta-and gamma-rays and the inherent energy spectra of radioactive isotopes. In the case of the sensing probe type 2, which is composed of two identical inorganic scintillators and a beta shielding material based on the lead, it could discriminate beta- and gamma-rays using a subtraction method. In conclusion, we demonstrated that the proposed fiber-optic beta/gamma dual detector could measure and discriminate beta- and gamma-rays using both energy spectroscopy and subtraction method.

• 한국연소학회:학술대회논문집
• /
• 2002.06a
• /
• pp.85-94
• /
• 2002

Computational flow dynamics(CFD) has been frequently applied to the waste incinerators to understand the flow performance for various design and operating parameters. Though it needs many simplifications and complicated flow models, the reasonability of its results is not fully evaluated. For example, the inlet condition is calculated from an arbitrarily assumed properties of combustion gas release from the waste bed, since the combustion in the bed is difficult to be predicted. In this study, the computational modeling and calculation procedures of CFD for the grate type waste incinerator were evaluated using comparative simulations. Though the assumption method on the generation of the combustion gas directly affected the temperature and gas species concentrations, the overall flow pattern was dominated by the secondary air jets. The gaseous reaction could be included by assuming the release of the products of incomplete combusion from the bed. However, the reaction effficiency cannot not be directly evaluated from the species concentration, since it is not possible to simulate the actual co-existence of fuel rich or oxygen rich puffs over the bed. In predicting the turbulence, the higher order model, such as Reynolds stress model, gave difference shape of local recirculation zones, but similar results was acquired from the standard $k-{\varepsilon}$ model. Introducing radiation model was required for accurate temperature prediction, but it also caused heat imbalance due to the fixed temperature of the inlet, i.e. the waste bed. Thus, the computational modeling procedures on incinerators and the analysis of the predicted results should be progressed carefully. Though not validated experimentally, current simulation method is capable of comparative evaluation on the flow-related parameters such as the furnace shape and secondary air injection using identical inlet conditions. Quantitative analysis using measures of the residence time and mixing is essential to compare the flow performance efficiently.

• Journal of Powder Materials
• /
• v.6 no.4
• /
• pp.314-319
• /
• 1999

The solid state reaction by mechanical alloying(MA) generally proceeds by lowering the free energy as the result of a chemical reaction at the interface between the two adjacent layers. However, Lee et $al.^{1-5)}$ reported that a mixture of Cu and Ta, the combination of which is characterized by a positive heat of mixing of +2kJ/mol, could be amorphized by mechanical alloying. This implies that there exists an up-hill process to raise the free energy of a mixture of pure Cu and la to that of an amorphous phase. It is our aim to investigate to what extent the MA is capable of producing a non-equilibrium phase with increasing the heat of mixing. The system chosen was the ternary $Cu_{30}Ta_{ 70-x}Mo_ x$ (x=35, 10). The mechanical alloying was carried out using a Fritsch P-5 planetary mill under Ar gas atmosphere. The MA powders were characterized by the X-ray diffraction with Cu-K $\alpha$ radiation, thermal analysis, electron diffraction and TEM micrographs. In the case of x=35, where pure Cu powders were mixed with equal amount of pure Ta and Mo powders, we revealed the formation of bcc solid solution after 150 h milling but its gradual decomposition by releasing fcc-Cu when milling time exceeded 200 h. However, an amorphous phase was clearly formed when the Mo content was lowered to x=10. It is believed that the amorphization of ternary $Cu_{30}Ta_{60}Mo_{10}$ powders is essentially identical to the solid state amorphization process in binary $Cu_{30}Ta_{70}$ powders.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.39-45
• /
• 2004

Experiments were performed in a two-phase swirling spray facility that has been described elsewhere. Measurements of spray transport and drop size distribution are analyzed over wide ranges of air to liquid mass flow ratios, utilizing four different internal mixing pneumatic nozzles. The spatial distributions of mean velocities. fluctuating velocities, and velocity-diameter correlation were quantitatively analyzed. Also, the exponential correlation curves were obtained with ALR along the spray centerline, which indicated an approximately identical formulation regardless of ALR. It indicated that the atomization characteristics were remarkably superior in the case of 30o of swirl angle with higher ALR. Among other things. nozzle configuration is one of the significant parameters affecting spray phenomena from an internal mixing nozzle. Turbulence intensities are increasingly degenerated with an increase of nozzle configuration, allowing a rapid increment of drop size distribution.

• Journal of Pharmaceutical Investigation
• /
• v.25 no.2
• /
• pp.109-116
• /
• 1995

For the administration of narcotic antagonist with short half-life and low patient compliance, the sustained release system using biodegradable matrix is effective. Polyphosphazenes are of considerable interest as biodegradable matrix systems for controlled release of drugs. In this study, biodegradable polyphosphazenes available for the sustained release implantable device were synthesized, and their application was examined. Poly[dichlorophosphazene] was synthesized by solution polymerization method and confirmed with IR spectrum. Poly[bis(ethyl glycinate) phosphazene] and poly[ (diethyl glutamate)-co-(ethyl glycinate)phosphazene] were then produced by substitution of amino acid alkyl esters for chloride side groups. Using these polymers, the implantable devices of 1 mm thickness and $10{\times}10\;mm$ size containing naloxone hydrochloride were prepared and their release and degradation profiles were measured. In the case of poly[bis(ethyl glycinate)phosphazene] with swelling characteristics, degradation rate was slower than the release rate, showing that the release rate is partly dependent on the swelling rate. In contrast, the degradation rate of polyl[(diethyl glutamate)-co-(ethyl glycinate)phosphazene] matrix was identical with release rate of naloxone hydrochloride. On the basis of these results, it is expected that these polymers can be applied to sustained release implantable systems delivering narcotic antagonist.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.6
• /
• pp.1169-1181
• /
• 1994

The Gamma Network contains the redundant path thereby is provides the ability to tolerate the faults occured. However, in case of identical the source and destination number, only a single path exists, therefore there is no way of connecting for the fault situation. In addition, for the dynamic packet routing strategy, it shoed perform backtracking analysis to find the redundant path. In this paper we proposed a new network, Dual Network, to resolve these drawbacks. The Dual Network uses switching elements about the same network size as the Gamma Network except first and last stage, and it is more efficient than the Gamma Network, for it has reduced the switching stage by one. And since is used a destination tag routing scheme for the control algorithm, it has on advantage of becoming of simpler and faster routing control.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.42 no.4
• /
• pp.194-202
• /
• 2019

Reliability analysis of the components frequently starts with the data that manufacturer provides. If enough failure data are collected from the field operations, the reliability should be recomputed and updated on the basis of the field failure data. However, when the failure time record for a component contains only a few observations, all statistical methodologies are limited. In this case, where the failure records for multiple number of identical components are available, a valid alternative is combining all the data from each component into one data set with enough sample size and utilizing the useful information in the censored data. The ROK Navy has been operating multiple Patrol Killer Guided missiles (PKGs) for several years. The Korea Multi-Function Control Console (KMFCC) is one of key components in PKG combat system. The maintenance record for the KMFCC contains less than ten failure observations and a censored datum. This paper proposes a Bayesian approach with a Dirichlet mixture model to estimate failure time density for KMFCC. Trends test for each component record indicated that null hypothesis, that failure occurrence is renewal process, is not rejected. Since the KMFCCs have been functioning under different operating environment, the failure time distribution may be a composition of a number of unknown distributions, i.e. a mixture distribution, rather than a single distribution. The Dirichlet mixture model was coded as probabilistic programming in Python using PyMC3. Then Markov Chain Monte Carlo (MCMC) sampling technique employed in PyMC3 probabilistically estimated the parameters' posterior distribution through the Dirichlet mixture model. The simulation results revealed that the mixture models provide superior fits to the combined data set over single models.

• Korean Journal of Materials Research
• /
• v.21 no.1
• /
• pp.15-20
• /
• 2011

The effects of conventional rolling (CR) and differential speed rolling (DSR) on the microstructure and mechanical properties of a copper alloy sheet were investigated in detail. A copper alloy with thickness of 3 mm was rolled to a 50% reduction at ambient temperature without lubrication with a differential speed ratio of 2:1; sample was then annealed for 0.5h at various temperatures from 100 to $800^{\circ}C$. Conventional rolling, in which the rolling speed of the upper and lower rolls is identical, was performed under the same rolling conditions. The shear strain introduced by the CR showed positive values at positions on the upper roll side and negative values at positions on the lower roll side. However, the shear strain showed a zero or positive value at all positions for the samples rolled by the DSR. The microstrucure and mechanical properties of the as-rolled copper alloy did not show very significant differences between the CR and DSR for the microstructure and mechanical properties. However, those properties showed very significant differences in the case of the annealed samples. The effects of rolling method on the microstructure and mechanical properties of the as-rolled and subsequently annealed materials are discussed in terms of the shear strain.

• The Journal of the Korea Contents Association
• /
• v.8 no.4
• /
• pp.227-236
• /
• 2008

The purpose of this study is to look around operation's present state of national universities and colleges sports and related subjects of leisure sports, and to propose the alternative and solution. I confirmed subject and major title by visiting address list of national universities and colleges which registered in education human resources department, in 2008 now. After the inquiry of that how many are the titles of sports and leisure sports related subjects in the inside of the country by using the internet and the other data, it is appeared that they use similar titles in the case of universities is about 50 and colleges is 43. As different as titles which uses by each subject, I expect the subject curriculum also be different, but actually it is not. It is appeared that the whole subject curriculum can't escape almost identical phase. we must see we can be selected in keen life competition stage. It is judged it is needed choice and concentration's decision in leisure sports related subjects.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.10
• /
• pp.45-50
• /
• 1999

We report a solder-clad fiber Bragg grating(FBG) temperature sensor in order to obtain better Bragg wavelength sensitivity to temperature than a bare FBG sensor. The solder-clad FBG sensor shows a wavelength sensitivity improvement by a factor of four compared to the case of a bare FBG sensor at temperatures below $110^{\circ}C$. However, it has a sensitivity of 0.01 $nm/^{\circ}C$ at temperatures over $110^{\circ}C$, which is identical to that of a bare FBG sensor. Bragg wavelength of the sensor shows a blue-shift below $110^{\circ}C$ because the sensor is fabricated above melting temperature of solder. The thermal stress at the FBG-solder interface has been relieved by annealing, which results in a stable operation.