• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.6
• /
• pp.657-664
• /
• 2008

This research compared several unsteady friction models for transient analysis of pipeline system. Unsteady friction is an important factor for accurate simulation of hydraulic transient. Steady friction, quasi-steady friction, Zielke's model and two versions of Brunone model were compared with measurement data of identical pipeline conditions. This study showed that the existing simple steady friction model can be useful for the safer design of pipeline system due to its overestimation of waterhammer, but introduction of more elaborate models are required for advanced analysis such as inverse transient analysis of friction or leakage and the preliminary analysis of water quality prediction of water distribution system.

• Economic and Environmental Geology
• /
• v.20 no.3
• /
• pp.159-168
• /
• 1987

Some physico-chemical properties such as surface area, moisture content, cation exchange capacity, swelling rate, pH, viscosity and liquid limit have been determined for evaluation of Cabentonite deposit occurring in four localities; Yonil, Gampo, Haseo and Pohang, in Gyeongsang-do. Montmorillonite contents can be derived from surface area measurement. Enhancement of liquid limit values and swelling volume were observed in the samples which had higher exchangeable Na ion and finer particle-size distribution. Identical results were observed even in the Na-exchanged samples. This suggests that aggregation effects have a great influence on physico-chemical properties. Aggregation of montmorillonite were controlled not only burial depth but also composition of exchangeable cation. Consequently, sample occurred in Yonil area where has the greatest burial depth in the area show somewhat lower physico-chemical properties than those of samples occurred in the other localities. However, the basic test applied in this study provides very useful preliminary information relating to its commercial potential.

• Journal of Welding and Joining
• /
• v.18 no.6
• /
• pp.62-67
• /
• 2000

Metallurgical characteristics of bonded region and high temperature mechanical properties of heat resistant alloy, Fe-35Ni-26Cr during liquid phase diffusion bonding were investigated employing AM17 insert metal. The insert metal for bonding, AM17 was newly developed Ni-base metal using interpolation method. Bonding of specimens were carried out at 1,403~1,463K for 600s in vacuum. The microconstituents in the bonded interlayer disappeared in the bonding temperature over 1,423K. The microstructures, alloying elements and hardness distribution in the base metal. The tensile strength and elongation of the joints at elevated temperatures were the same level as one of the base metal in the bonding temperature over 1,423K. The creep rupture strength and rupture lives of joints were almost identical to those of base metal.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.9 s.90
• /
• pp.779-784
• /
• 2004

This paper numerically analyzes the dynamic characteristics of a spindle system supported by two identical journal bearingsconsidering bearing span that has dynamic load due to its mass unbalance. The Reynolds equation is transformed to solve a herringbone grooved journal bearing. The Reynolds equations are solved using FEM in order to calculate the pressure distribution in a fluid film. Reaction forces and friction torque are obtained by integrating the pressure and shear stress along the fluid film, respectively. Dynamic behaviors, such as whirl radius or angular displacement of a rotor, are determined by solving its nonlinear equations of motion with the Runge-Kutta method. This research shows that the same bearing spans of upper and lower journal bearings produce the minimum runout and friction torque of a spindle system.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.7
• /
• pp.364-369
• /
• 2004

In this Paper, a flashover prediction method using the leakage current in the contaminated EPDM distribution polymer insulator is proposed. The leakage currents on the insulator were measured simultaneously with the different salt fog application such as 25g, 50g, and 75g per liter of deionized water. Then, the measured leakage currents were enveloped and transformed as the CDFS using the Hilbert transform and the level crossing rate, respectively. The obtained CDFS having different gradients(angles) were used as a important factor for the flashover prediction of the contaminated polymer insulator. Thus, the average angle change with an identical salt fog concentration was within a range of 20 degrees, and the average angle change among the different salt fog concentrations was 5 degrees. However, it is hard to be distinguished each other because the gradient differences among the CDFS were very small. So, the new weighting value was defined and used to solve this problem. Through simulation, it Is verified that the proposed method has the capability of the flashover prediction.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.7
• /
• pp.1152-1157
• /
• 1994

The glasses were prpared in the system CuI-CuS12TS-CuS12TO-MoOS13T by rapid quenching technique. These glasses have high ionic conductivities at 2$0^{\circ}C$ in the range of 10S0-1T[S/m], and the conductivities increase with increasing CuI and CuS12TS content. The value of activation energy for dielectric relaxation is nearly identical with that for conductivity. The cole-Cole parameter $\beta$ for representation of the distribution of dielectric relaxation times varies the range from 0.92 to 0.96. This parameter has a weak dependence on the composition of glass, and is independent of temperature. The correlation factors P for the glasses shows from 1.1 to 1.7.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1863-1868
• /
• 2004

The present study concerns a computational study of fully developed laminar flow of a Newtonian fluid through an eccentric annulus with a combined bulk axial flow and inner cylinder rotation. This study considers the identical flow geometry as in the calculation of Escudier et $al.^{(3)}$ An unexpected feature of the calculations for eccentricity ${\varepsilon}$)0.7 is the appearance of a second peak in the axial velocity, located in the narrowing gap. The distribution of the axial component of the surface shear stress has a maximum in the narrowing gap and a minimum in the widening gap.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.229-234
• /
• 1999

This thesis presents the design method using CAE(Computer Aided Engineering) with the consideration of reliability for optimal gear driving system. The validity and feasibility of the proposed method are verified by the application to transmission of machine tool. The reliability and life analysis is based on the two-parameter Weibull distribution lives of the gears and bearings. Ninety-percent of reliability life is the life of the component or system in million output rotations or hours at which ninety percent of identical components or system would survive under the given loading conditions.

• ETRI Journal
• /
• v.31 no.2
• /
• pp.225-227
• /
• 2009

A new planar metamaterial (MTM) with simultaneous negative values of permittivity (${\varepsilon}$) and permeability (${\mu}$) is proposed. Our MTM is composed of two identical copper patterns etched on both sides of dielectric laminate, which is very thin and easy to fabricate. Unlike conventional MTMs, the proposed structure shows a negative refractive index (NRI) behavior with respect to a normally incident wave. To explain the underlying principle of the NRI characteristics, an equivalent resonant circuit model based on surface current density distribution is investigated. An eigenmode analysis and a three-dimensional wave simulation for the stacked MTM prism are also performed to verify the existence of negative refraction. The experimental results from the transmission and reflection measurement ensure the validity of our design approach and show good agreement with the theoretically predicted effective medium parameters.

• KSCI Review
• /
• v.15 no.1
• /
• pp.185-190
• /
• 2007

An image retrieval system is a piece of software that searches identical or similar images based on various image-specific features. This paper proposes a trademark image retrieval system that uses image colors and forms. In the proposed system, input images are segmented into several other regions, and color distribution histograms for different regions are extracted for use as color information. The proposed system uses form information through the preprocessing process such as boundary surface extraction, centroid extraction, angular sampling and, and through calculating the sums of the distances between the centroid and the boundary surfaces, standard deviations, and the ratios between long and short axes. Like this, the color and form information extracted is used to perform retrieval through measuring similarity.