• Journal of the Korean Ceramic Society
• /
• v.31 no.7
• /
• pp.804-812
• /
• 1994

Stable PZT coating sol was prepared using chelating agent, ethylacetoacetate(EAcAc) by sol-gel processing under ambient atmosphere. Through FT-IR spectrum analysis on solution of each reaction step, formation of metal complex was confirmed and prepared PZT sol was stable over several months. Through TG-DTA, XRD, FT-IR spetrum analysis of PZT gel powder, it was understood that the addition of EAcAc could reduce the transition temperature to ferroelectric phase, due to the increased homogeneity by matching the hydrolysis and condensation rates by chelation. Single perovskite phase was obtained by the heat-treatment at 54$0^{\circ}C$ for 30 min. The film was coated on ITO-coated glass substrate by dip coating method. After heat-treatment, PZT thin film had thickness in the range of 20~130 nm. The maximum dielectric constant of its thin film at room temperature and 1 kHz was 128.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.7
• /
• pp.446-449
• /
• 2015

An improvement of light-extraction efficiency of organic light-emitting diodes was studied by using random-textured films (RTF). Device was made in a structure of RTF/glass/ITO/TPD/$Alq_3$/LiF/Al. RTF mold was made by spreading PDMS solution on a sandpaper. By pressing this mold on the glass substrate pre-coated with ZPU material, the RTF was obtained. From this study, there was an improvement of external quantum efficiency by about 30% in the device with the random-textured film (RTF 40) compared to that of the reference one.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.11
• /
• pp.961-968
• /
• 2009

In this work, transparent conductive oxide(TCO) films such as $In_2O_3-SnO_2$(ITO) and $In_2O_3-ZnO$(IZO) were prepared on polyethylene naphthalene(PEN) and glass substrates by using rf-magnetron sputtering system. The TCO films deposited on PEN substrate show very poor conductivity as compared to that of the TCO films deposited on glass substrates. From the results of the residual gas analysis(RGA) test, this poor stability of plastic substrate is presumed to be caused by the deteriorated adhesion between the TCO films and the plastic substrate due to outgassing from the plastic substrate during deposition of TCO films. From our experiment, it is found that the vaporization of some defects in the plastic substrates deteriorate the adhesion of the TCO films to the plastic substrate, because the most plastic substrates containing the water vapor and/or other adsorbed particles such as organic solvents. Mixing of these gases vaporized in the sputtering process will also affect the electrical property of the deposited TCO films. Inorganic thin composite $(SiO_2)_{40}(ZnO)_{60}$ film as a gas barrier layer is coated on the PEN substrate to protecting the diffusion of vapors from the substrate, so that the TCO films with an improved quality can be obtained.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.2
• /
• pp.129-134
• /
• 2012

We analyzed the movement and response time of charged particles according to particle-inserting methods to understand the variation of quantity of q/m of charged particles, which is a very important factor in electrical and optical characteristics of the charged particle type display, such as lifetime, response time, contrast ratio, reflectivity, etc. For our study we used white and black charged particles of which diameter is $20{\mu}m$, prepared pieces of ITO(indium tin oxide) coated glass substrate, and formed ribs on the glass substrates. The width of a rib is $30{\mu}m$ and the cell size is $220{\mu}m{\times}220{\mu}m$. As the particle-inserting methods, the white and black charged particles were respectively inserted into a front and a rear panel with a very small electric field and also the mixture of the white and black charged particles were inserted into a rear panel. As a result of the driving characteristics of charged particles, the factors about variation of quantity of q/m according to the particle inserting method was experimentally demonstrate, showing very different driving voltage, response time, the particle movement, etc.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.63-67
• /
• 2010

The organic solar cells with Glass/ITO/PEDOT:PSS/P3HT:PCBM/Al structure were fabricated using regioregular poly (3-hexylthiophene) (P3HT) polymer:(6,6)- phenyl $C_{61}$-butyric acid methyl ester (PCBM) fullerene polymer as the bulk hetero-junction layer. The P3HT and PCBM as the electron donor and acceptor materials were spin casted on the indium tin oxide (ITO) coated glass substrates. The optimum mixing concentration ratio of photovoltaic layer was found to be P3HT:PCBM = 4:4 in wt%, indicating that the short circuit current density ($J_{SC}$), open circuit voltage ($V_{OC}$), fill factor (FF) and power conversion efficiency (PCE) values were about 4.7 $mA/cm^2$, 0.48 V, 43.1% and 0.97%, respectively. To investigate the effects of the post annealing treatment, as prepared organic solar cells were post annealed at the treatment time range from 5min to 20min at $150^{\circ}C$. $J_{SC}$ and $V_{OC}$ increased with increasing the post annealing time from 5min to 15min, which may be originated from the improvement of the light absorption coefficient of P3HT and improved ohmic contact between photo voltaic layer and Al electrode. The maximum $J_{SC},\;V_{OC}$, FF and PCE values of organic solar cell, which was post annealed for 15min at $150^{\circ}C$, were found to be about 7.8 $mA/cm^2$, 0.55 V, 47% and 2.0%, respectively.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.3
• /
• pp.90-97
• /
• 2010

$TiO_2$ thin films for solar energy utilization were prepared on ITO coated glass by r.f magnetron sputtering with variations of working pressure, oxygen flow rate and annealing temperature. Ion insertion and extraction reaction, and ion storage properties of films were investigated by using a cyclic voltammetry. Transmittance of thin films in as-prepared, colored and bleached states was measured by UV-VIS spectrophotometer. The samples deposited in our sputtering conditions showed poor electrochromic properties. Improvement in ion storage properties of $TiO_2$ thin film was observed after annealing at temperature of $400^{\circ}C$ in air for 2 hours. It was found that $TiO_2$ thin film in electrochromic device could be used as a passive counter-electrode.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.2
• /
• pp.140-144
• /
• 2000

($Pb_{0.91}$$La_{0.09}$)($Zr_{0.65}$$Ti_{0.35}$)$O_3$ thin films were prepared on ITO-coated glass by spin-coating. As $Pb_{0.9}$$La_{0.1}$)$TiO_3$ thin films were used as seeding layers, formation temperature of perovskite was reduced and theUrosette" structure was disappeared. PLZT thin films with a seeding layer of 40 nm thick showed a (100) preferred orientation and better dielectric and ferroelectric properties.ties.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.5
• /
• pp.1038-1042
• /
• 2004

The photoelectric responses of a biodevice consisting of chlorophyll $\alpha$ Langmuir-Blodgett film were investigated. Chlorophyll $\alpha$ Langmuir-Blodgett films were deposited onto ITO and Au coated glass. To confirm film formation, surface analysis of chlorophyll $\alpha$ Langmuir-Blodgett film was carried out by measurement using atomic force microscopy. The metal/insulator/metal structured biodevice was constructed by depositing aluminum onto the chlorophyll $\alpha$ Langmuir-Blodgett film surface. To investigate the photoelectric response, the current-voltage characteristic was measured by the conducting metal tip. The photoswitching function and transient photovoltage characteristics of the proposed device were measured by irradiation with Ar ion laser and $N_2$ pulse laser, respectively. This research suggested that the proposed biodevice consisting of chlorophyll $\alpha$ could be applied to the molecular scale biosensor and/or bioelectronic device.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.1.1-4
• /
• 1995

In this study, PLZT thin films in AFE region prepared by sol-gel processing were investigated. And PLZT stock solutions were spin-coated on ITO-glass. The PLZT thin films were annealed by RTA. Hysteresis curves, dielectric characteristics and optical transmittances were measured in order to investigates the characteristics far the thin films. The PLZT thin films were crystallized at 750$^{\circ}C$ for 5 mimutes by RTA and the rosette structure composed of perovskite observed in the thin films. In case La content was 2/90/10 antiferroelectric-ferroelectric phase boundary was 2/90/10 PLZT thin film, and its hysteresis curve was good for application of optical information storage.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1440-1442
• /
• 2005

We have fabricated vertical type organic thin film transistors (OTFTs) using organic semiconductor materials such as F16CuPc, NTCDA, PTCDI C-8 and C60. The layers of OTFT were fabricated by vacuum evaporation technique and spin casting method onto the Indium Tin Oxide (ITO) coated glass. I-V characteristics and on-off ratios of the fabricated OTFTs were investigated. In addition, we have fabricated light emitting transistor using MEH-PPV and then investigated EL electroluminescent properties.