• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.45 no.1
• /
• pp.31-40
• /
• 2022

Six Sigma is a philosophy and systematic methodology for quality improvement. It encourages continuous quality improvement efforts to achieve the ideal goal of 6σ. Sigma(σ) is a statistic representing the standard deviation of the normal distribution, and 6σ level means a level where the tolerance of the specification is six times the standard deviation of the process distribution. In terms of the defective rate, the 6σ level achieves the 0.002 defectives per one million units. However, in the field, the 6σ level is used in the sense of achieving 3.4 defects per one million opportunities, which shows a large gap from the 6σ level in the statistical viewpoint. This is because field practitioners accept a 1.5σ shift of the mean of process when calculating the defective rate under sigma level. It said that the acceptance of 1.5σ shift of the mean is from experience, but there is no research or theoretical explanation to support it logically. Although it is a non-scientific explanation based on experience, considering that there has been no objection to the 1.5σ shift for a long time and it is rather accepted, it is judged that there is a reasonable basis for the 1.5σ shift. Therefore, this study tries to find a reasonable explanation through detective power of control chart via the run-rules to the 1.5σ shift empirically recognized by practitioners.

• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.246-251
• /
• 2020

The annealing characteristics of cold-rolled Al-6.5Mg-1.5Zn-0.5Fe-0.5Mn alloy, newly designed as an automobile material, are investigated in detail, and compared with those of other aluminum alloys. Using multi-pass rolling at room temperature, the ingot aluminum alloy is cut to a thickness of 4 mm, width of 30 mm, and length of 100 mm to reduce the thickness to 1 mm (r = 75 %). Annealing after rolling is performed at various temperatures ranging from 200 to 500 ℃ for 1 hour. The specimens annealed at temperatures up to 300 ℃ show a deformation structure; however, from 350 ℃ they have a recrystallization structure consisting of almost equiaxed grains. The hardness distribution in the thickness direction of the annealed specimens is homogeneous at all annealing temperatures, and their average hardness decreases with increasing annealing temperature. The tensile strength of the as-rolled specimen shows a high value of 496 MPa; however, this value decreases with increasing annealing temperature and becomes 338 MPa after annealing at 400 ℃. These mechanical properties of the specimens are compared with those of other aluminum alloys, including commercial 5xxx system alloys.

• Journal of Korean Society of Forest Science
• /
• v.53 no.1
• /
• pp.62-74
• /
• 1981

The developed record of forest maschines and tools in West Germany, Austria and Swiss, their technical characteristics and the working methods with them have been tried to investigate through the study of literature and observation. The aim of this investigation is to find out and introduce the technical information for training our forest men with them and for improving or developing our forest maschines and tools. Although ax chosen as first report for this aim is the oldest tool in the mankind history, still this is widely using in the forest work. And this has some special working filed that any other maschines could not overcome and sometimes should be recommended in the agronomical sideview. Through this investigation several points could be proposed as the technical informations when we will try to improve our ax 1. Radius of as-face curvature is proposed to be 150 mm and it's central point to be passed at one third point near to ax-eye. 2. Cutting angle is proposed to be $30^{\circ}$, ax-thick at 12 mm distance from ax-face to be 4 mm, thick at 30 mm distance from face to be 5 to 6 mm and ax-face width to be $125{\pm}5mm$. 3. Neck size is proposed to be $3.5{\pm}0.5{\times}5.5{\pm}0.5cm$ with a little curvature and neck thick from ax-house to be more than 1.5 cm. 4. Ax weight is proposed to be 1,000 gr with the stupid back and the sharp front. 5. The handle length of ax will be followed to the arm length of our forest workers.

• Journal of Food Hygiene and Safety
• /
• v.18 no.4
• /
• pp.218-223
• /
• 2003

This study was to carried out to estimate the relationship between acceleration storage and room temperature storage of gangjung (control unit) and dried insam gangjung (experiment unit), by acid value and peroxide value. The result were summarized as follows. : 1. Test for acid value of control unit, every 1 hour after acceleration storage is similar to each 7 days after room temperature storage is imilar to each 7.5 days after room temeprature storage. 2. Test for peroxide value of control unit, evry 1 hour after acceleration storage is similar to each 7.5 days after room temperature storage but to test peroxide value of experiment unit, every 1 hour after acceleration storage is imilar to each 7.7 days after room temperature storage. 3. In case of the oxidized flavor, control unit is not detected during storage stability but the experiment unit is detected unit is detected 1 hour ahead of acceleration storage than room temperature storage.

• Korean Journal of Optics and Photonics
• /
• v.14 no.5
• /
• pp.515-520
• /
• 2003

Characteristics of an amplifier with repetition rate of a few KHz is investigated. The continuous flash lamp pumped Nd:YAG laser head is used as an amplifier. The thermally induced birefringence of the laser medium is compensated and the depolarization is reduced to 5% in a double-pass amplifier. The amplification factor of a four pass amplifier reaches to about 3.2 at the repetition rate 5-10 KHz and the pulse width is lengthened from 40 ns to 48 ns.

• Journal of Integrative Natural Science
• /
• v.14 no.2
• /
• pp.50-56
• /
• 2021

Due to the recent increase in the mobile streaming market, mobile traffic is increasing exponentially. IMT-2020, named as the next generation mobile communication standard by ITU, is called the 5th generation mobile communication (5G), and is a technology that satisfies the data traffic capacity, low latency, high energy efficiency, and economic efficiency compared to the existing LTE (Long Term Evolution) system. 5G implements this technology by utilizing a high frequency band, but there is a problem of path loss due to the use of a high frequency band, which is greatly affected by system performance. In this paper, small cell technology was presented as a solution to the high frequency utilization of 5G mobile communication system, and furthermore, the system performance was improved by applying machine learning technology to macro communication and small cell communication method decision. It was found that the system performance was improved due to the technical application and the application of machine learning techniques.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.7 s.172
• /
• pp.122-129
• /
• 2005

Shoe with leather upper such as safety and golf shoe requires a roughing process where the upper is roughed fur helping outsole to be cemented well. It is an important and basic process for production of leather shoe but is not automated yet. Thus, there are problems that the defect rate is high and the quality of roughed surface is not uniform. In order to solve such problems, the interest in automation of roughing process is being increased and this paper introduces CAM system for 5-axis automatic roughing machine as one part of automation of roughing process. The CAM system developed interpolates a B-spline curve using points measured from the Roughing Path Measurement System. The B-spline curve is used to generate the tool path and orientation data fer a roughing tool which has not only stiffness but also flexibility to rough the inclined surface efficiently. For productivity, the upper of shoe is machined by side of the roughing tool and tool offset is applied to the roughing tool for machining of inclined surface. The generated NC code was applied to 5-axis polishing machine for the test. The upper of shoe was roughed well along the roughing path data from CAM and the roughed surface was proper fur cementing of the outsole.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.890-893
• /
• 2004

The ultra precision machining in industrial field are increased day by day. The diamond turning has been used generally, but now is faced with limitation of use, because of higher requirement of production field. The electron beam lithography is alternative in machining area as semiconductor production. For EB lithography, 5 axis vacuum stage is required to duplicate small and large patterns on wafer. The stage is composed of 2 rotational axis and 3 translational axis with 5 DC servo motors. The positioning repeatability and resolution of Z axis feed unit are 3.21$\mu$m and 0.5 $\mu$m/step enough to apply to lithography.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.6
• /
• pp.1643-1648
• /
• 2010

Adenosine 5'-phosphonates have been reported as potential chain terminators against Hepatitis C virus (HCV); therefore, we developed convenient sequences for synthesis of modified adenosine 5'-phosphonates in which the hydroxyl group at 2' or 3'-position of the sugar moiety is substituted with the azido or amino group and the oxymethyl group at the 4'-position is modified by the ethylene or vinyl group. This synthetic sequence can provide six adenosine 5'-phosphonates via one protocol, and is considered to be very efficient and a convenient route of synthesis. An assay of adenosine 5'-phosphonate analogues (1, 2, 3, 4, 5, and 6) against HCV infection is now in progress.

• Electronics and Telecommunications Trends
• /
• v.38 no.5
• /
• pp.114-124
• /
• 2023

Recently, there have been the World Economic Forum's space economy guidelines, the International Telecommunication Union's regulations for each satellite orbit, the development of chips using satellite communication by global manufacturers and service providers, and the registration of key telecommunication businesses. Accordingly, trends in low-orbit 5G satellite communication services in Korea were investigated and analyzed, and the current situation in Korea was diagnosed. Korea's satellite communications accounts for 0.31% of all satellites when analyzed centering on countries with 20 or more satellites. Korea's communication satellite holdings are insufficient compared to 187 times that of the United States, 45 times that of Russia, and 18 times that of China. There is no link technology between 5G and LEO, and the cost of launch vehicles is high. In addition, it is judged that the ecosystem of equipment companies in the low-orbit 5G-NTN business model is insufficient.