• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.5
• /
• pp.2156-2170
• /
• 2020

This paper presents a fire detection algorithm with a minimal false detection rate, intended for a thermal imaging surveillance environment, whose properties vary depending on temporal conditions of day or night and environmental changes. This algorithm was designed to minimize the false detection alarm rate while ensuring a high detection rate, as required in fire detection applications. It was necessary to reduce false fire detections due to non-flame elements occurring when existing fixed threshold-based fire detection methods were applied. To this end, adaptive flame thresholds that varied depending on the characteristics of input images, as well as the center of gravity of the heat-source and hot-source regions, were analyzed in an attempt to minimize such non-flame elements in the phase of selecting flame candidate blocks. Also, to remove any false detection elements caused by camera shaking, one of the most frequently raised issues at outdoor sites, preliminary decision thresholds were adaptively set to the motion pixel ratio of input images to maximize the accuracy of the preliminary decision. Finally, in addition to the preliminary decision results, the texture correlation and intensity of the flame candidate blocks were averaged for a specific period of time and tested for their conformity with the fire decision conditions before making the final decision. To verify the fire detection performance of the proposed algorithm, a total of ten test videos were subjected to computer simulation. As a result, the fire detection accuracy of the proposed algorithm was determined to be 94.24%, with minimum false detection, demonstrating its improved performance and practicality compared to previous fixed threshold-based algorithms.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.9
• /
• pp.97-105
• /
• 2011

This paper proposes a new "Live Book Service" that is combined the analog contents such as paper books and digital contents with various digital multimedia elements, and this service can project the additional digital multimedia contents on the analog paper. Also, we developed a monolithic stand type system which is composed of camera and pico projector, so that it can demonstrate the proposed contents. We also devised the low computational cost algorithm in bare-hands recognition which can be used as the interface between the system and users. In addition, to recognize the bare-hands which can be used as the interface between the digital and users, we make the low cost algorithm. Therefore this can be the interaction between the system and users. As a result, our proposed system can be used as a useful tool for various e-book or u-learning fields that requires high efficiency and much immersion.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.4
• /
• pp.323-329
• /
• 2013

This perform research of angle rated defect detection conditions and nuclear power plant piping defect detection by lock-In infrared thermography technique. Defects were processed according to change for wall-thinning length, Circumference orientation angle and wall-thinning depth. In the used equipment IR camera and two halogen lamps, whose full power capacitany is 1 kW, halogen lamps and target pipe's distance fixed 2 m. To analysis of the experimental results ensure for the temperature distribution data, by this data measure for defect length. Reliability of lock-In infrared thermography data is higher than Infrared thermography data. This through research, Shape of angle rated defect is identified industry place. It help various angles defect detection in the nuclear power plant in operation.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.5
• /
• pp.243-248
• /
• 2014

This study presents an investigation into the ways to detect the areas of object movement with Kinect's Depth Frame, which is capable of receiving 3D information regardless of external light sources. Applied to remove noises along the boundaries of objects among the depth information received from sensors were the blurring technique for the x and y coordinates of pixels and the frequency filter for the z coordinate. In addition, a clustering filter was applied according to the changing amounts of adjacent pixels to extract the areas of moving objects. It was also designed to detect fast movements above the standard according to filter settings, being applicable to mobile robots. Detected movements can be applied to security systems when being delivered to distant places via a network and can also be expanded to large-scale data through concerned information.

• The KIPS Transactions:PartB
• /
• v.16B no.3
• /
• pp.203-214
• /
• 2009

In this paper, we could simply compute the user's gaze position based on 2D relations between the pupil center and four corneal specular reflections formed by four IR-illuminators attached on each corner of a monitor, without considering the complex 3D relations among the camera, the monitor, and the pupil coordinates. Therefore, the objectives of our paper are to detect the pupil center and four corneal specular reflections exactly and to compensate for error factors which affect the gaze accuracy. In our method, we compensated for the kappa error between the calculated gaze position through the pupil center and actual gaze vector. We performed one time user calibration to compensate when the system started. Also, we robustly detected four corneal specular reflections that were important to calculate gaze position based on Kalman filter irrespective of the abrupt change of eye movement. Experimental results showed that the gaze detection error was about 1.0 degrees though there was the abrupt change of eye movement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.1033-1036
• /
• 2002

Wafer bonding methods such as fusion and anodic bonding suffer from high temperature treatment, long processing time, and possible damage to the micro-scale sensor or actuators. In the localized bonding process, beating was conducted locally while the whole wafer is maintained at a relatively low temperature. But previous research of localized heating has some problems, such as non-uniform soldering due to non-uniform heating and micro crack formation on the glass capsule by thermal stress effect. To address this non-uniformity problem, a new heater configuration is being proposed. By keeping several points on the heater strip at calculated and constant potential, more uniform heating, hence more reliable wafer bonding could be achieved. The proposed scheme has been successfully demonstrated, and the result shows that it will be very useful in hermetic packaging. Less than 0.2 ㎫ contact Pressure were used for bonding with 150 ㎃ current input for 50${\mu}{\textrm}{m}$ width, 2${\mu}{\textrm}{m}$ height and 8mm $\times$ 8mm, 5mm$\times$5mm, 3mm $\times$ 3mm sized phosphorus-doped poly-silicon micro heater. The temperature can be raised at the bonding region to 80$0^{\circ}C$, and it was enough to achieve a strong and reliable bonding in 3minutes. The IR camera test results show improved uniformity in heat distribution compared with conventional micro heaters. For gross leak check, IPA (Isopropanol Alcohol) was used. Since IPA has better wetability than water, it can easily penetrate small openings, and is more suitable for gross leak check. The pass ratio of bonded dies was 70%, for conventional localized heating, and 85% for newly developed FP scheme. The bonding strength was more than 30㎫ for FP scheme packaging, which shows that FP scheme can be a good candidate for micro scale hermetic packaging.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.2
• /
• pp.95-101
• /
• 2009

This study is the research on the thermal emissivity depending on the bulk graphite's alignment degree. Bulk graphites were manufactured by uni-axial pressing and subsequent heat treatment of natural graphite flakes with organic binder. The samples were prepared to be $0^{\circ}$ (relative to the 002 c-face), $45^{\circ}$, and $90^{\circ}$ (relative to the 100 a-face) for measuring alignment degree. The alignment degree of the sample was measured by XRD. The thermal emissivity was measured by infrared thermal image camera at $100^{\circ}C$ and compared with the value obtained by Infrared spectroscopy. The alignment degree and thermal emissivity of $0^{\circ}$ sample were measured to be 0 and 0.70 respectively. And those of $90^{\circ}$ sample were 0.73 and 0.80 respectively. The emissivity value was correlated with obtained by IR spectroscopy. Therefore it was considered that the thermal emissivity of the bulk graphite is correlated with the alignment degree.

• Journal of the Korean Solar Energy Society
• /
• v.35 no.4
• /
• pp.67-75
• /
• 2015

PV module is conventionally connected in series with some solar cell to adjust the output of module. Some bypass diodes in module are installed to prevent module from hot spot and mismatch power loss. However, bypass diode in module exposed outdoor is easily damaged by surge voltage. In this paper, we study the thermal and electrical characteristics change of module with damaged bypass diode to easily find module with damaged bypass diode in photovoltaic system consisting of many modules. Firstly, the temperature change of bypass diode is measured according to forward and reverse bias current flowing through bypass diode. The maximum surface temperature of damaged bypass diode applied reverse bias is higher than that of normal bypass diode despite flowing equal current. Also, the output change of module with and without damaged bypass diode is observed. The output of module with damaged bypass diode is proportionally reduced by the total number of connected solar cells per one bypass diode. Lastly, the distribution temperature of module with damaged bypass diode is confirmed by IR camera. Temperature of all solar cells connected with damaged bypass diode rises and even hot spot of some solar cells is observed. We confirm that damaged bypass diodes in module lead to power drop of module, temperature rise of module and temperature rise of bypass diode. Those results are used to find module with a damaged bypass diode in system.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.1
• /
• pp.50.1-50.1
• /
• 2014

The Multi-purpose InfraRed Imaging System (MIRIS) is the main payload of Science and Technology Satellite 3 (STSAT-3), which was launched onboard Dnepr rocket from Russian Yasny Launch Base in November 2013. The MIRIS is an infrared (IR) camera, and the telescope has to be cooled down to below 200K in order to reduce thermal background noise. For the effective cooling and low-power consumption, we applied passive cooling method to the thermal design of the MIRIS. We also conducted thermal analysis and tested for the passive cooling before the launch of STSAT-3. After the launch, we have received State-of-Health (SOH) data from the satellite on orbit, including temperature monitoring results. It is important that the temperature of the telescope was shown to be cooled down to below 200K. In this paper, we present both the temperature data of the MIRIS on orbit and the thermal analysis results in the laboratory. We also compare these results and discuss the verification of the passive cooling.

• Journal of the Korea Society of Computer and Information
• /
• v.13 no.5
• /
• pp.187-193
• /
• 2008

Interface technologies for a user to control home automation system in wearable computing environment has been studied recently. This paper proposes a new interface method for a disabled person to control home automation system in wearable computing environment by using EOG sensing circuit and marker recognition. In the proposed interface method, the operations of a home network device are represented with human readable markers and displayed around the device. A user wearing a HMD, a video camera, and a computer selects the desired operation by seeing the markers and selecting one of them with eye movement from the HMD display The requested operation is executed by sending the control command for the selected marker to the home network control device. By using the EOG sensing circuit and the marker recognition system a user having problem with moving hands and fit can manipulate a home automation system with only eye movement.