• The KIPS Transactions:PartA
• /
• v.14A no.7
• /
• pp.391-398
• /
• 2007

In this paper, we design a future mobile camera standard interface based on the MIPI CSI-2 and D-PHY specification. The proposed CSI-2 have the efficient multi-lane management layer, which the independent buffer on the each lane are merged into single buffer. This scheme can flexibly manage data on multi lanes though the number of supported lanes are mismatched in a camera processor transmitter and a host processor. The proposed CSI-2 & D-PHY are verified under test bench. We make an experiment on CSI-2 & D-PHY with FPGA type test-bed and implement them onto a mobile handset. The proposed CSI-2 & D-PHY module are used as both the bridge type and the future camera processor IP for SoC.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.10
• /
• pp.677-682
• /
• 2017

Lamination is used extensively in various industries. The type of lamination applied to the material depends on the precision level required, which varies for materials needed for everyday use, materials used in high-tech industries, and processes employed to fabricate finished products. Especially in hot lamination, the distribution of the surface temperature of the heating roller is very important to avoid the generation of internal bubbles and ensure flatness of the attached materials, and thus maintain a good standard of quality and productivity. In this study, we have developed a system to monitor the surface temperature of the heating rollerby applying a heterogeneous controller and a non - contact temperature sensor. This monitoring system accurately measures the surface temperature of the heating roller and applies the RS485 MODBUS communication method for easy expansion. Using this system, a laminated prototype was fabricated, and its efficacy for non-contact temperature sensor calibration, Ethernet IP communication, stoppage of the heating roller, and determination of temperature distribution with rotation was examined for its potential usage in industries.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.437-440
• /
• 2003

Recently, the study on the design of NCS(Network Control System) using Ethernet is being rapidly progressed. NCS can be extensively applied in manufacturing automation, office automation, home automation, remote control and ect. A merit of NCS on based Ethernet is to make good use of advanced Internet environment and to apply a application of abundant TCP/IP upper layer to NCS. The purpose of this paper is to control a speed of DC-motor using NCS on based Ethernet. The control system is divided into a server part and a client part. A server transfers a value of reference speed of a DC-motor. A client receives a output signal of DC-motor and a reference input obtained from the server. A client computes a error of two signals and then makes a control input. The control input is transferred to a actuator In this pater, A controller uses a classical control using a general feedback. In this paper, a viewpoint is to compare performance of NCS with performance of a classical control and to analyze the cause of that.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.218-223
• /
• 1993

In this paper, we present a full digital control scheme which controls currents and speed of the permanent magnet AC servo motor with large range of bandwidth and high performance. The current equations of the permanent magnet AC servo motor are linearized by feedback linearization technique. Both acceleration feedforward terms and IP controllers, whose gains are functions of motor speed, are used in order to control motor currents. In addition the phase delays in current control loops are compensated by placing phase lead-lag compensators after current commands, which make it possible to avoid high gains in the current controllers. Unity power factor can be achieved by the proposed current controller. Pulsewidth modulation is performed by way of the well-known comparison with a triangular carrier signals. The velocity controller is designed on the basis of the linearized model of the permanent magnet AC servo motor by the proposed current controller. The performance of the entire control system is analyzed in the presence of uncertainty in the motor parameters. The proposed control scheme is implemented using the digital signal processor-based controller composed of an Analog Device ADSP 2111 and a NEC78310. The pulsewidth modulation (PWM) signals are generated through a custom IC, SAMSUNG-PWM1, which has the outputs of current controllers as input. The experimental results show that the permanent magnet AC servo motor can be always driven with high dynamic performance by the proposed full digital control scheme of motor speed and motor current.

• Journal of the Institute of Convergence Signal Processing
• /
• v.11 no.1
• /
• pp.53-62
• /
• 2010

Recently, various industrial embedded systems including vehicles controlled electronically are evolving to distributed multi-micro controller system. Accordingly, there is a need for standard CAN(Controller Area Network) protocol that ensures high stability and reliability of communication and is simple to construct object-oriented system with high control efficiency. CAN communication interface used general-purpose processor doesn't have many limitations in various application development because of fixed hardware architecture. This paper design and implement a CAN communication interface system based on FPGA. It is verified function and performance of system through monitoring communication with existing AT90CAN128 controller. Implemented CAN communication interface can be reused in development of application systems based on FPGA. And it provides low-cost, small-size and low-power design advantages.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.7
• /
• pp.1-11
• /
• 2002

This paper proposes that an efficient routing entry sending method between routing controller FE. based on this method, we organize IP VPN support method based on MPLS network and design MPLS-VPN service control module, MPLS-VPN processing, VPN group configuration and LSP setup processing. We evaluate the performance about the VPN based on proposed MPLS, at the result of evaluation. We figure out that based on proposed IPC method, lost packets number reduces and delay increases more slowly in case of VPN based on MPLS comparing with the VPN based on ATM which has rapid delay increasement. Therefore we confirm that the VPN based on MPLS has high speed of packet processing and high utilization of buffers through the performance evaluation.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.2
• /
• pp.9-16
• /
• 2004

As the industry is developed, uses of various electric motor are increasing from general home to various fields of industry, and the kind becomes various daily. For these reasons, it is required to study the remote control and a package management about change of a speed drive system the supervision of administration appliance by real time, and the collection and process data together using internet prevailed on industry whole. Also, we can expect big effect in time and space, side of cost-cutting by control directly and manage appliance through internet. This paper deals with the development of a Web-Based remote control system for permanent magnet synchronous motor drives. The client/server system using TCP/IP protocols and DSP controller for remote control through internet and the Web interface that users can confirm data and state of PMSM is developed. This system is available for driving, braking, variable speed control and monitoring for PMSM in real time through administration program of Web-Based.

• Journal of Power Electronics
• /
• v.3 no.2
• /
• pp.115-123
• /
• 2003

This paper presents analysis, design and simulation for the indirect field orientation control (IFOC) of induction machine drive system. The dynamic performance of the IFOC under nominal and detuned parameters of the induction machine is established. A conventional proportional plus integral-derivative (PI-D) two-degree-of-freedom controller (2DOFC) is designed and analysed for an ideal IFOC induction machine drive at nominal parameters with the desired dynamic response. Varying the induction machine parameters causes a degredation in the dynamic response for disturbance rejection and tracking performance with PI-D 2DOF speed controller. Therefore, conventional controllers can nut meet a wide range of speed tracking performance under parameter variations. To achieve high- dynamic performance, a proposed robust fuzzy logic controllers (RFLC) for d-axis rotor flux, d-q axis stator currents and rotor speed have been designed and analysed. These controllers provide robust tracking and disturbance rejection performance when detuning occurres and improve the dynamic behavior. The proposed REL controllers provide a fast and accurate dynamic response in tracking and disturbance rejection characteristics under parameter variations. Computer simulation results demonstrate the effectiveness of the proposed REL controllers and a robust performance is obtained fur IFOC induction machine drive system.

• The KIPS Transactions:PartC
• /
• v.17C no.1
• /
• pp.129-134
• /
• 2010

Intelligent Power Switch (IPS) is a semiconductor device which contains a logic circuit in itself. It has received significant attention as a switching component to substitute the fuse and relay components in common automobile since the internal logic provides the controllability on the loads. However, a control system for the IPS status control and a network system to share the status information of IPS are required to fully exploit the capabilities of IPS. In this paper, we propose a control circuit and algorithm using IPS. Also the communication system between the control systems and IPS components using Control Area network (CAN) are proposed.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.4
• /
• pp.229-236
• /
• 2005

This paper presents a system level architecture evaluation technique that leverages transaction level modeling but also significantly extends it to the realm of system level performance evaluation. A major issue lies with the modeling effort. To reduce the modeling effort the proposed technique develops the concept of worst case scenarios. Since the memory controller is often found to be an important component that critically affects the system performance and thus needs optimization, the paper further addresses how to evaluate and optimize the memory controllers, focusing on the test environment and the methodology. The paper also presents an industrial case study using a real state-of-the-art design. In the case study, it is reported that the proposed technique has helped successfully find the performance bottleneck and provide appropriate feedback on time.