• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.623-624
• /
• 2006

In this paper, we introduce the design and fabrication of V-band power amplifier MMIC with excellent gain-flatness for IEEE 802.15.3c WPAN system. The V-band power amplifier was designed using ETRI' $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The gains of the each stages of the amplifier were modified to have broadband characteristics of input/output matching for first and fourth stages and get more gains of edge regions of operating frequency range for second and third stages in order to make the gain-flatness of the amplifier excellently for wide band. The performances of the fabricated 60 GHz power amplifier MMIC are operating frequency of $56.25{\sim}62.25\;GHz$, bandwidth of 6 GHz, small signal gain ($S_{21}$) of $16.5{\sim}17.2\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-16{\sim}-9\;dB$, output reflection coefficient ($S_{22}$) of $-16{\sim}-4\;dB$ and output power ($P_{out}$) of 13 dBm. The chip size of the amplifier MMIC was $3.7{\times}1.4mm^2$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37B no.11
• /
• pp.1004-1013
• /
• 2012

The legacy voice broadcast systems are used to broadcast the voice over an entire space or a specific zone. these broadcast systems generate unnecessary noise and waste of resources. In this paper, we propose a ubiquitous voice message broadcast system called uPaging, by combining the technique of location-awareness and the voice message delivery service in ubiquitous sensor network environment. In uPaging system, the wire/wireless hybrid network is used to implement the network system. Also, in order to actualize the location-awareness service, we use the Bidirectional Location ID-Exchange protocol was suggested by our previous research. the uPaging system can deliver the voice to a selected user or the location in which the user is present by this location awareness.

• Journal of Navigation and Port Research
• /
• v.33 no.3
• /
• pp.193-197
• /
• 2009

In this paper, the EM wave absorber was designed and fabricated for improvement of Wireless LAN environment at 2.4 GHz. We fabricated several samples in different composition ratios of Sendust and CPE(Chlorinated Polyethylene). Absorption abilities were simulated in accordance with different thicknesses of the prepared absorbers and changed complex relative permittivity and permeability due to composition ratio. The mixing ratio of Sendust and CPE was searched as 80: 20 wt.% by experiments and simulation Then the EM wave absorber was fabricated and tested using the simulated data. As a result, the EM wave absorber was fabricated based on simulated data. Simulated and measured results agreed well. As a result, the developed EM wave absorber with thickness of 3.25 mm has absorption ability of 19 dB at 2.4 GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.6B
• /
• pp.595-604
• /
• 2009

The HCCA reserves the channel resources based on the mean data rate in IEEE 802.11e. It may cause either the waste of channel resource or the increase of transmission delay at MAC layer if the frame size is rapidly varied when a compressed mode video codec such as MPEG video is used. To solve these problems, it is developed that the packet scheduler allocates the wireless resource adaptation by according to the packet size. However, it is difficult to perform the admission control because of the difficulty with calculating the available resources. In this paper, we propose a CAC mechanism to solve the problem that may not satisfy the QoS by increasing traffic load in case of using EDCA. Especially, the proposed CAC mechanism calculates the EB of TSs using the traffic information transmitted by the application layer and the number of average transmission according to the wireless channel environment, and then determines the admission of the TS based on the EB. According to the simulation results of the proposed CAC mechanism, it admitted the TSs under the loads which are satisfied within the delay bound. Therefore, the proposed mechanism guarantees QoS of streaming services effectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.2
• /
• pp.95-100
• /
• 2011

This paper analyzes the interference effect of WLAN(Wireless Local Area Network) service on WiBro(Wireless Broadband) service in adjacent frequency band by using Monte Carlo method. For the analysis, we make scenario that WLAN service operates on frequency band of 2401 MHz ~ 2423 MHz and WiBro service operates on frequency band of 698 MHz ~ 704 MHz. In case of WiBro receiver is close to WLAN AP(Access Point), the interference will be increased. So, we calculate the protection distance between WiBro receiver and WLAN AP to meet interference probability of 5 % below and required interference power of WLAN AP to meet interference probability of 5 % below in the case of fixed protection distance. As a result, the protection distance of 60 m and -9.5 dBm of required interference power of WLAN AP at 10 m of the fixed protection distance are analyzed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.8
• /
• pp.623-631
• /
• 2013

Wireless LAN (WLAN) interface is one of the major sources drastically depleting the battery power of mobile devices such as smartphones and tablets. Most commercial mobile devices employ a power saving technique putting their WLAN interface into a sleep state when there is no network traffic, and thereby, save the battery power. However, since an access point (AP) just transmits the packet(s) received from a server to the corresponding mobile device immediately, it may cause a problem that the mobile device constantly remains in an awake state so that its battery power is rapidly drained. In this paper, we point out this problem and propose a new scheme that can save the mobile device's battery power with an adaptive packet scheduling at the AP side. From the experimental results based on a testbed, we found that the proposed scheme outperforms existing schemes over 50% in terms of power saving.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.9A
• /
• pp.755-761
• /
• 2005

In this paper, we proposed a channel estimation method by impulse signal train in OFDM. In order to estimate the channel response, 4 impulse signals are generated and transmitted during one OFDM (Orthogonal Frequency Division Multiplexing) symbol. The intervals between the impulse signals are all equal in time domain. At the receiver, the impulse response signals are summed and averaged. And then, the averaged impulse response signal is zero padded and fast Fourier transformed to obtain the channel estimation. The BER performance of the proposed method is compared with those of conventional estimation method using the long training sequence in fast fading environments. The simulation results show that the proposed method improves by 3 dB in terms of Eb/No, compared with the conventional method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.7
• /
• pp.775-782
• /
• 2016

In this paper, we presented the paper-based reconfigurable frequency selective surface(FSS) for transmitting or blocking the wireless LAN signal in indoor environments. The proposed reconfigurable FSS are designed on coated paper using a printing of conductive ink and conductive adhesive for PIN diode, which provides ON/OFF of the reconfigurable FSS for passing or blocking the 5GHz signal. The reconfigurable FSS attached on the wall can pass or block the incident wireless signal as the received signal strength in indoor. To provide the validity of the proposed FSS, we fabricated the reconfigurable FSS on the paper and confirmed the very similar results between simulations and measurements. From the measured results of the proposed spectrum control system, we know that the proposed reconfigurable FSS can block about 20dB at 5.745GHz~5.805GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.4B
• /
• pp.391-398
• /
• 2011

In this paper, we propose a MAC protocol for visible light wireless LAN using LED light. The proposed MAC protocol has a function of automatic direction optimization for LED transceiver. There is periodical time slot for broadcasting and registration in the proposed MAC protocol. We used polling method for data transfer in the protocol since visible light is hard to detect carrier and collision by other mobile stations; thus we cannot use CSMA/CD method in visible light LAN. We also amended the MAC frame of IEEE 802.11 to propose a revised version for visible light wireless LAN using LED light. We investigate the performance of the proposed MAC protocol. When the bit rate of physical layer is 100 Mb/s, the net data throughput using the proposed MAC protocol is estimated to 94.386 Mb/s.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.6
• /
• pp.726-732
• /
• 2019

In this study, we proposed an asymmetric differential inductor to improve the linearity of differential power amplifiers. Considering the phase error between differential signals of the differential amplifier, the location of the center tap of the differential inductor was modified to minimize the error. As a result, the center tap was positioned asymmetrically inside the differential inductor. With the asymmetric differential inductor, the AM-to-AM and AM-to-PM distortions of the amplifier were suppressed. To confirm the feasibility of the inductor, we designed a 2.4 GHz differential CMOS PA for IEEE 802.11n WLAN applications with a 64-quadrature amplitude modulation (QAM), 9.6 dB peak-to-average power ratio (PAPR), and a bandwidth of 20 MHz. The designed power amplifier was fabricated using the 180-nm RF CMOS process. The measured maximum linear output power was 17 dBm, whereas EVM was 5%.