• Journal of the korean academy of Pediatric Dentistry
• /
• v.29 no.3
• /
• pp.469-477
• /
• 2002

One of the major deficiencies of composite restorative resins is their insufficient resistance to wear. Of the multitude of factors that have been associated with wear, subsurface degradation within the restoration is considered to be one. The aim of this study was to evaluate the resistance to degradation of four commercial composite resins in an alkaline solution. The brands studied were Z100(3M), Clearfil AP-X(Kuraray), Tetric Ceram(Vivadent), Aelit flo(Bisco). Resistance to degradation was evaluated on the basis of the following parameters: (a) mass loss(%) - determined from pre-and post-exposure specimen weights: (b) Si loss(ppm) - obtained from ICP-AE analysis of solution exposed to specimens; and (c) degradation depth(${\mu}m$) - measured microscopically (SEM) from polished circular sections of exposed specimens. The results were as follows: 1. The sequence of the mass loss was in ascending order by AE, EL, TC, Z100. There was statistically significant difference of mass loss between AE, CL group and TC, Z100 group(p<0.05). 2. The sequence of the degree of degradation layer depth was in ascending order by AE, CL, TC, Z100. But there was no statistically significant difference of degree of degradation layer depth between AE and CL(p<0.05). 3. For the Si concentration, Z100 was the highest of all. 4. The correlation coefficient between mass loss and degradation depth was relatively high(r=0.71 p<0.05).

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.372-381
• /
• 2015

The effect of preparation method on the catalytic activities of the $Ni/Al_2O_3$ catalysts on steam reforming of ethylene glycol was investigated. The catalysts were prepared with various preparation methods such as an incipient wetness impregnation, wet impregnation, and coprecipitation method. In the case of coprecipitation method, various precipitants such as KOH, $K_2CO_3$, and $NH_4OH$ were compared. The prepared catalysts were characterized by using $N_2$ physisorption, inductively coupled plasma-atomic emission spectroscopy, X-ray diffraction, temperatureprogrammed reduction, pulsed $H_2$ chemisorption, temperature-programmed oxidation, scanning electron microscopy, and thermogravimetric analysis. Among the catalysts reduced at 773 K, the $Ni/Al_2O_3$ catalyst prepared by a coprecipitation with KOH or $K_2CO_3$ as precipitants showed the best catalytic performance. The preparation method affected the particle size of Ni, reducibility of nickel oxides, catalytic performance (activity and stability), and types of coke formed during the reaction. The $Ni/Al_2O_3$ catalyst prepared by a coprecipitation with KOH showed the increasing catalytic activity with an increase in the reduction temperature from 773 to 1173 K because of an increase in the reduction degree of Ni oxide species even though the particle size of Ni increased with increasing reduction temperature.

• Korean Journal of Food Science and Technology
• /
• v.29 no.6
• /
• pp.1113-1118
• /
• 1997

Chemical components of domestic Angelica gigas Nakai and Angelica acutiloba Kitagawa were analyzed. Proximate analysis of each species showed crude protein 18.1% and 13.4%, crude lipid 8.9% and 4.3%, crude fiber 8.6% and 9.4%, crude ash 7.4% and 8.2%, and carbohydrate 57.0% and 64.7%, respectively. Contents of potassium which was found to be the most abundant mineral in both species were 2,740.0 mg% and 2,582.8 mg%, and those of sucrose were 0.4 % and 0.3% respectively while neither fructose nor glucose were detected in each species. Major fatty acids in Angelica gigas Nakai and Angelica acutiloba Kitagawa were linoleic acid (60.8% and 59.5%), palmitic acid (17.4% and 15.3%), oleic acid (8.8% and 7.7%) (respectively) but there was no significant difference between two species. Arginine was revealed as the most abundant amino acid in both species with 2,599.8 mg% in Angelica gigas Nakai and 1,543.4 mg% in Angelica acutiloba Kitagawa. Angelica gigas Nakai and Angelica acutiloba Kitagawa also were shown to contained 10.5 mg% and 12.2 mg% $vitamin\;B_1$, 0.1 mg% and 0.04 mg%, $vitamin\;B_2$, 4.3% and 0.8% decursin, and 988.0 mg% and 900.0 mg% tannin, respectively.

• Economic and Environmental Geology
• /
• v.42 no.1
• /
• pp.27-53
• /
• 2009

A 30-m-thick Middle Ordovician Jigunsan Shale exposed along the southern limb of the Backunsan (Baekunsan) Syncline, Taebacksan (Taebaeksan) basin, has been simply considered as a transgressive shale sequence onlapped the underlying Maggol platform carbonates. Results of this study, however, suggest that majority of the Jigunsan Shale be interpreted as a regressive shale sequence downlapped onto a thin (ca. 240 cm) marine stratigraphic unit consisting of organic-rich (>3 wt.% of TOC) black shales in the lower Jigunsan Shale, which was accumulated at the time of maximum regional transgression. Detailed stratigraphic analysis in conjunction with XRD, XRF, and ICP-MS as well as Rock-Eval pyrolysis allows the thin marine stratigraphic unit in the Jigunsan Shale to define a condensed section that was deposited in a distinctive euxinic zone formed due to expansion of pycnocline during the early highstand phase. As well, a number of stratigraphic horizons of distinctive character that may have sequence stratigraphic or environmental significance, such as transgressive surface, maximum flooding surface, maximum sediment starvation surface, and downlap surface, are identified in the lower Jigunsan Shale. In the future, these stratigraphic horizons will provide very useful information to make a coherent regional stratigraphic correlation of the Middle Ordovician strata and to develop a comprehensive understanding on stratigraphic response to tectonic evolution as well as basin history of the Taebacksan Basin.

• Resources Recycling
• /
• v.29 no.1
• /
• pp.25-34
• /
• 2020

Electrochemical Quartz Crystal microbalance is a tool that is capable of measuring nanogram-scale mass change on electrode surface. When applying alternating voltage to the quartz crystal with metal electrode formed on both sides, a resonant frequency by inverse piezoelectric effect depends on its thickness. The resonant frequency changes sensitively by mass change on its electrode surface; frequency increase with metal dissolution and decrease with metal deposition on the electrode surface. The relationship between resonant frequency and mass change is shown by Sauerbrey equation so that the mass change during metal dissolution can be measured in real time. Especially, it is effective in the case of reaction mechanism and rate studies accompanied by precipitation, volatilization, compound formation, etc. resulting in difficulties on ex-situ AA or ICP analysis. However, it should be carefully considered during EQCM experiments that temperature, viscosity, and hydraulic pressure of solution, and stress and surface roughness can affect on the resonant frequency. Application of EQCM was shown as a case study on leaching of platinum using aqueous chlorine for obtaining activation energy. A platinum electrode of quartz crystal oscillator with 1000 Å thickness exposed to solution was used as leaching sample. Electrogenerated chlorine as oxidant was purged and its concentration was controlled in hydrochloric acid solution. From the experimental results, platinum dissolution by chlorine is chemical reaction control with activation energy of 83.5 kJ/mol.

• Journal of Applied Biological Chemistry
• /
• v.61 no.4
• /
• pp.391-395
• /
• 2018

There is an increasing concern over arsenic (As) contamination of paddy soil and rice with regard to food safety. This study was conducted to investigate total and inorganic As concentration in one hundred husked and polished rice samples collected at the non-contaminated paddy soil in Korea. Arsenic species in rice samples were extracted using 1% nitric acid ($HNO_3$) with a microwave oven and were measured using high performance liquid chromatography coupled with inductively coupled plasma-mass spectrometry. Mean concentrations of total As in husked rice and polished rice were 0.18 and $0.11mg\;kg^{-1}$, respectively. Also, average inorganic As concentrations in husked rice and polished rice were 0.11 and $0.07mg\;kg^{-1}$, respectively. These levels are lower than the standard guideline value 0.35 and $0.2mg\;kg^{-1}$ for inorganic As in husked and polished rice recommended by Codex Committee on Contaminants in Foods and Ministry of Food and Drug Safety, respectively. The mean of the inorganic As ratio for the total amount of As was 0.65 and 0.67 for husked rice and polished rice, respectively, and the range was from 0.08 to 1.0. For health risk assessment, the average value of cancer risk probability was $9.24{\times}10^{-5}$ and ranged from $2.30{\times}10^{-5}$ to $1.90{\times}10^{-5}$. Therefore, human exposure to As through dietary intake of surveyed rice samples might considered to be a low health risk.

• Applied Chemistry for Engineering
• /
• v.22 no.2
• /
• pp.167-172
• /
• 2011

In this work, the effect of surface treatment on mesoporous carbons (MCs) supports was investigated by analyzing surface functional groups. MCs were prepared by a conventional templating method using mesoporous silica (SBA-15) for using catalyst supports in direct methanol fuel cells (DMFCs). The MCs were treated with different phosphoric acid ($H_3PO_4$) concentrations i.e., 0, 1, 3, 4, and 5 M at 343 K for 6 h. And then Pt-Ru was deposited onto surface treated MCs (H-MCs) by chemical reduction method. The characteristics of Pt-Ru catalysts deposited onto H-MCs were determined by specific surface area and pore size analyzer, X-ray diffraction, X-ray photoelectron, transmission electron microscopy, and inductive coupled plasma-mass spectrometer. The electrochemical properties of Pt-Ru/H-MCs catalysts were also analyzed by cyclic voltammetry experiments. From the results of surface analysis, an oxygen functional group was introduced to the surface of carbon supports. From the results, the H4M-MCs carbon supports surface treated with 4 M $H_3PO_4$ led to uniform dispersion of Pt-Ru onto H4M-MCs, resulting in enhancing the electro-catalytic activity of Pt-Ru catalysts.

• Journal of the Korean earth science society
• /
• v.42 no.1
• /
• pp.1-10
• /
• 2021

Silicon (Si) is the second most abundant element in the crust and consists of three stable isotopes, 28Si (92.23%), 29Si (4.67%), and 30Si (3.10%). Si isotopes are widely studied worldwide as a proxy for the biogeochemical cycle of Si to reconstruct the paleoenvironment and paleoclimate. However, in Korea, there have been no studies on biogenic silica using Si isotopes. In this study, we carried out Si isotope measurements of giant diatoms, summarizing the previously reported alkali fusion methods and establishing the best Si separation method for biogenic silica. Samples were completely digested using alkali fusion at high temperatures, effectively separating Si using an AG® 50W-X8 cation exchange resin. To evaluate the precision and accuracy of our measurements, Si isotope standard material (NBS-28) and USGS reference materials (AGV-2, GSP-2, BHVO-2) were analyzed. The results are in excellent agreement with the reported values within the acceptable error. The Si isotope measurement method developed in this study is expected to help in understanding the paleoclimate and paleoenvironment by tracing the Si cycle.

• Korean Journal of Community Nutrition
• /
• v.27 no.3
• /
• pp.245-253
• /
• 2022

Objectives: This study was conducted to find out if the dietary iron intake of Koreans estimated by 2 different methods (iron content sources) using the food intake data from the Korea National Health and Nutrition Examination Survey (KNHANES) are comparable. One method was based on the KNHANES's Food & Nutrient Database (FND) derived mainly from the Korean Food Composition Table and the other used the iron content (IC) of food samples processed in the Korean Total Diet Study (KTDS). Methods: Dietary intake data from the 2013-2016 KNHANES was used to select representative foods (RFs) in KTDS for iron analysis. Selection of the RFs and cooking methods for each RF (RF × cooking method pair) was performed according to the 'Guidebook for Korean Total Diet Studies' and resulted in a total of 132 RFs and 224 'RF × cooking method' pairs. RFs were collected in 9 metropolitan cities nationwide once or twice (for those with seasonality) in 2018 and made into 6 composites each, based on the origin and season prior to cooking. Then, the RF composites prepared to a 'table ready' state for KTDS were analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS). Dietary iron intake of the Korean population was estimated using only RFs' intake data based on the 2 sources of iron content, namely FND-KNHANES and IC-KTDS. Results: RFs in KTDS covered 92.0% of total food intake of Koreans in the 2016-2018 KNHANES. Mean iron intake of Koreans was 7.77 mg/person/day by IC-KTDS vs 9.73 mg/person/day by FND-KNHANES. The major food groups contributing to iron intake were meats (21.7%), vegetables (20.5%), and grains & cereals (13.4%) as per IC-KTDS. On the other hand, the latter source (FND-KNHANES) resulted in a very different profile: grains & cereals (31.1%), vegetables (16.8%), and meats (15.3%). While the top iron source was beef, accounting for 8.6% in the former, it was polished rice (19.2%) in the latter. There was a 10-fold difference in the iron content of polished rice between 2 sources that iron intakes excluding the contribution by polished rice resulted in very similar values: 7.58 mg/person/day by IC-KTDS and 7.86 mg/person/day by FND-KNHANES. Conclusions: This study revealed that the dietary iron intake estimated by 2 different methods were quite comparable, excluding one RF, namely polished rice. KTDS was thus proven to be a useful tool in estimating a 'closer-to-real' dietary intake of nutrients for Koreans and further research on various nutrients is warranted.

• Journal of Radiopharmaceuticals and Molecular Probes
• /
• v.7 no.2
• /
• pp.119-125
• /
• 2021

⁸²Sr for ⁸²Rb generator was produced through the irradiation of the proton beam on the ^nat.RbCI target at the target irradiation facility installed at the end of the Rl-dedicated beamline of the 100 MeV proton linear accelerator of KOMAC (Korea Multi-purpose Accelerator Complex). The average current of the proton beam was 1.2 µA for irradiation time of 150 min. For the separation and purification of the ⁸²Sr from ^nat.RbCI irradiated, Chelex-100 resin was used. The activities of ⁸²Sr in the irradiated ^nat.RbCI target solution and after purification were 45.29 µCi and 43.4 µCi, respectively. The separation and purification yield was 95.8%. As an adsorbent to be filled in the generator for ⁸²Sr adsorption hydrous tin oxide was selected. The adsorption yield of ⁸²Sr into the generator adsorbent was > 99 %, and the total amount of ⁸²Sr adsorbed to the generator was 21.6 µCi as of the day of the ⁸²Rb elution experiment. When the elution amount was 22 mL, the maximum⁸²Rb elution yield was 93.3%, and the elution yield increased as the flow rate increased. After the eluted ⁸²Rb was filled in the correction phantom of the small PET for animals, a PET image was taken. The image scan time was set to 5 min, and the phantom PET image was successfully obtained. As results of impurity analysis on eluted ⁸²Rb using ICP-MS, ^nat.Rb stable isotopes that compete in vivo of ⁸²Rb were identified as undetected levels and were determined to be No-Carrier-Added (NCA).