• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.2
• /
• pp.117-127
• /
• 2019

Vessel's ice speed performances will be verified in ice sea trial but environmental conditions of ice fields are changeable according to the weather condition of ice trial area. Speed performance has to correct in the no wind, wave and current etc. after sea trial. Especially finding ice fields which is exact the same as owner's ice thickness and strength requirements is not easy. Therefore speed correction according to environment condition has to be done after sea trial measurements. Correction methods for ice thickness, ice strength, wave, wind and ship draft, trim, ice drift etc. are checked in ice sea trial based on literature review such as ISO standard, ITTC recommendation, journal papers and proceedings of conferences. Possibility of application for current and ice drift correction in ice field are discussed and measuring schemes and procedures of correction methods are described in this paper. All of correction schemes are calculated for 'Araon' which is ice breaking research vessel with Arctic and Antarctic ice field test results. Analyzed results shows that Araon is satisfied with her official ice speed performance of 3 knots with 10MW power at 1m ice thickness, 570kPa ice flexural strength.

• Journal of Ocean Engineering and Technology
• /
• v.9 no.1
• /
• pp.36-46
• /
• 1995

빙판파괴 형태는 여러 모드의 합성이며 실제로 한 가지 양식으로 파괴되는 경우는 거의 일어나지 않는다. 이제까지 빙하중 해석 이론이나 방법은 한 가지 양식에 기준하는 것이었다. 이 논문에서는 합성모드로 빙판이 파괴될 때 해양구조물에 작용하는 빙하중 추정방법을 소개하여 모형 실험결과치와 그 결과를 비교하였다. 두 가지 합성모드에 대한 빙하중 추정방법인 비례파괴해석법 (Proportional Failure Method)과 국부경계해석법(Local Ice boundary Method)을 본논문에 소개하였으며, 이 두가지 방법과 함께 널리 알려진 Crushing 해석방법을 적용하여 정적 및 동적 구조물에 작용하는 빙하중을 산출/비교하였다. 동적구조물은 쇄빙선을 이용하였고, 쇄빙선이 SPM 터미널에 monopod로 연결되어있는 형태를 선택하였다. 모형 실험은 Finland의 Wartsila 실험실에서 실시 하였고, 이 실험을 통하여 쇄빙선에 작용하는 빙력 및 시간별 쇄빙선의 동적 움직임을 측정하였다. 이 논문에서는 위에서 소개된 세가지 방법으로 계산된 빙하중과 실험측정결과를 비교하였고, 이론적으로 추정한 쇄빙선의 운동을 실혐결과치와 비교하였다. Crushing방법으로 산출한 빙하중은 실제치보다 상당히 높았고, 비례파괴해석법은 Crushing 방법보다 정확한 결과를 보여주었으며, 국부경계해석법은 상당히 모형실험측정치와 가까웠다. 물론 쇄빙선의 움직임도 빙하중에 따라 변화가 심했고, 국부 경계해석법을 적용했을 때 실제 쇄빙선의 동적움직임을 가장 가깝게 추정할 수 있었다.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.469-477
• /
• 2012

This paper describes the characteristic analysis of ice impact force for the Arctic structure shape. In the present study an energy method has been used to predict the impact force during the ice-structure collision. This study also employs two concepts for reference contact area and normalized stress in analysis procedure. The influences of factors, such as impact velocity, full penetration depth, structure shape and ice floe size, are investigated. Full penetration occurs, particularly at lower impact velocity when ice thickness increase. But "typical size" ice floe does not expected ever to achieve full penetration during the impact procedure. The structure shape is the dominant factor in ice impact force characteristic. The results for various ice-structure collision scenarios are analyzed.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.2
• /
• pp.104-109
• /
• 2015

The Korea Research Institute of Ships & Ocean Engineering (KRISO) has an ice tank to make a test environment similar to the real ice in the polar sea in order to carry out model tests. One of the most important task of the ice tank is to generate the model ice to have similar material properties as sea ice. The primary properties of sea ice which influence the ice performance of ice breakers and ice-strengthened vessels traveling in the polar sea are ice thickness, flexural strength, density, modulus of elasticity and crystal structure etc. Among them, since the density of model ice influences the buoyance resistance of ice for the ship model, the accurate measurement of ice density should be used to obtain the accurate analysis results from the model test. In this paper, some existing methods to measure the density of model ice are reviewed and a new one is proposed to measure it accurately and easily as possible. In this study, the measuring system including an UTM and several measuring devices was established to obtain the model ice density. Polyethylene and ice specimens are used for a series of repeatable measurement tests. From the results, it was recognized that both of the displacement method and the weight/weight methods gave the stable and favorable tendency.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.1 no.1
• /
• pp.87-92
• /
• 1989

In this study, the nonlinear dynamic model of the systems which include the offshore structure, the surrounding sea water in terms of the added mass, the foundation in terms of frequency independent springs, dashpots, and the floating ice feature with its hydrodynamic added mass, are proposed for the problem of the large ice floes impact. Dynamic Analysis is performed on two site conditions, sand site and silt site, and on two seasons, winter and summer, for various ice floe velocities. As a result of study, Ice floes from energy balenced method is lower than that from dynamic modeling on sand site, and higher than the on silt site.

• KIPS Transactions on Software and Data Engineering
• /
• v.10 no.7
• /
• pp.257-262
• /
• 2021

Accidents caused by black ice occur frequently every winter, and the fatality rate is very high compared to other traffic accidents. Therefore, a systematic method is needed to predict the black ice formation before accidents. In this paper, we proposed a black ice prediction model based on heterogenous and multi-type data. To this end, 12,574,630 cases of 46 types of land, infrastructure, transport public data and meteorological public data were collected. Subsequently, the data cleansing process including missing value detection and normalization was followed by the establishment of approximately 600,000 refined datasets. We analyzed the correlation of 42 factors collected to predict the occurrence of black ice by selecting only 21 factors that have a valid effect on black ice prediction. The prediction model developed through this will eventually be used to derive the route-specific black ice risk index, which will be utilized as a preliminary study for black ice warning alart services.

• Journal of Advanced Navigation Technology
• /
• v.27 no.6
• /
• pp.865-870
• /
• 2023

Recently, accidents caused by black ice, a road freezing phenomenon caused by natural power, are increasing. Black ice is difficult to identify directly with the human eye and is more likely to misunderstand it as standing water, so there is a high accident rate caused by car sliding. To solve this problem, this paper presents a method of detecting black ice centered on LiDAR sensors. With a small, inexpensive, and high-accuracy light detection and ranging (LiDAR) sensor, the temperature and inclination angle are set differently to detect black ice and asphalt by setting different reflection angles of asphalt and black ice differently in temperatures and inclinations. The LIDARO carried out in the study points out that additional research and improvement are needed to increase accuracy, and through this, more reliable black ice detection methods can be suggested. This method suggests a method of detecting black ice through early system design research by preventing accidents caused by black ice in advance.

• Journal of the Korea Computer Graphics Society
• /
• v.26 no.5
• /
• pp.1-13
• /
• 2020

In this paper, we propose a new method to stable simulation the directional ice shape by coupling of freezing solver and viscous water flow. The proposed ice modeling framework considers viscous fluid flow in the direction of ice growth, which is important in freezing simulation. The water simulation solution uses the method of applying a new viscous technique to the IISPH(Implicit incompressible SPH) simulation, and the ice direction and the glaze effect use the proposed anisotropic freezing solution. The condition in which water particles change state to ice particles is calculated as a function of humidity and new energy with water flow. Humidity approximates a virtual water film on the surface of the object, and fluid flow is incorporated into our anisotropic freezing solution to guide the growth direction of ice. As a result, the results of the glaze and directional freezing simulations are shown stably according to the flow direction of viscous water.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2008.10a
• /
• pp.145-148
• /
• 2008

ICESat launched in Jan. 2003 has a capability to monitor polar regions with its inclination of 94 degree. ICESat carries GLAS (Geosciences Laser Altimetry System) to measure Earth's topography in unprecedented accuracy, and thus it can be applied for glacier variation due to recent climate changes. Here we present a new method to estimate velocity structure of Amery Ice-Shelf using ICESat altimtery data. ICESat data shows horizontal displacement of Amery Ice-Shelf, which can be directly used for velocity estimation. This method is expected to extend to other ice-shelves in Antarctica.

• Journal of Navigation and Port Research
• /
• v.37 no.2
• /
• pp.129-135
• /
• 2013

Recently, waste water treatment system is developed in small and middle size to get more economic advantage. Freeze concentration system has high thermodynamic efficiency and low energy consumption, can re-use purified water and cold energy obtained from ice. This study was experimentally performed to investigate pollution containment in frozen layer by cooling wall temperature, air-bubble flow methods, initial ice-lining thickness of frozen layer in NaCl aqueous solution and the representative heavy metals, Pb and Cr aqueous solution. As the result, a decrease in the cooling wall temperature bring a higher growth rate of ice front and the more solute was involved in frozen layer. The method to inject directly air-bubble into ice-liquid interface through ring shape nozzle gave high purity of ice compared to indirect method. Ice lining in 5mm thickness resulted in frozen layer with higher purity than 1mm thickness.