• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.20-27
• /
• 1998

According as the member of the automobile body structure have been thinned their thickness and have become high strength, each part of the body structure has been put more severe stress condition. And, because fatigue strength of the spot welded lap joint is influenced by its geometrical and mechanical factors, welding condition and etc., there needs a quantitative and systematic evaluation method for them. In this study, by considering nugget edge of the spot weld part of the IB-type spot welded lap joint under tension-shear load to the ligament crack. fatigue strength of various IB-type spot welded lap joints was estimated with the stress intensity factor(S.I.F.) KIII which is fracture mechanical parameter. We could find that fatigue strength evaluation of the IB-type spot welded lap joints by KIII is more effective than the maximum principal stress ($\sigma$1max) at edge of the spot weld obtained from FEM analysis.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.32-37
• /
• 1999

Since stainless steel plates have good mechanical properties, weldability, appearance and resistance of corrosion, these are traditionally used for vehicles such as the bus and the train. And they are mainly fabricated by spot welding. But fatigue strength of their spot welded joint is considerably influenced by welding conditions as well as geometrical factors. Thus a reasonable and systematic criterion for long life design of spot welded body structure must be established. In this report, strain energy density was analyzed by using 3-dimensional finite element model about the IB-type spot welded lap joint under tension-shear load. Fatigue tests were conducted on them having various thickness, joint angle, lapped length and width. From their results, it was found that fatigue strength of the IB-type spot welded lap joints could be effectively and systematically rearranged by strain energy density at the edge of nugget.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.25-31
• /
• 1999

Stainless steel sheets are commonly used for vehicles such as the bus and the train. These are mainly fabricated by spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget. edge of the spot-welding. By the way, its fatigue strength is lower than base metal due to high stress concentration at the nugget edge of the spot-welding point. Especially, it is influenced by welding conditions as well as geometrical factors of spot welded joint. Therefore, it is not too much to say that structural rigidity and strength of spot-welded structures is decided by fatigue strength of spot welded lap joint. Thus, it is necessary to establish a reasonable and systematic long life design criterion for the spot-welded structure. In this study, numerical stress analysis was performed by using 3-dimensional finite element model on IB-type spot-welded lap joint of 304 stainless steel sheet under tension-shear load. Fatigue tests were also conducted on them having various thickness, joint angle, lapped length, and width of the plate. From the results, it was found that fatigue strength of IB-type spot-welded lap joints was influenced by its geometrical factors, however, could be systematically rearranged by maximum principal stress ({TEX}$σ_{1max}${/TEX}) at the nugget edge of the spot-welding point.

• Journal of Mechanical Science and Technology
• /
• v.14 no.11
• /
• pp.1187-1197
• /
• 2000

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.3
• /
• pp.1-8
• /
• 2000

To develop the technology of producing structural board from low grade materials, an attempt was made to produce strand/particle composites from split wood strand(S) and particle(P) of (Cryptomeria japonica D. Don), which changed the layer construction and the ratio of S/P. The influence of layer construction on board properties was determined, focusing on the number and alignment of the S layers. The effect of weight ratio of S/P (3:7, 1:1, 7:3) on mechanical properties was also discussed on seven layered panel. Mechanical properties were determined from static bending tests to give parallel and perpendicular modulus of rupture (MOR) and modulus of elasticity (MOE), and the internal bond (IB) strength. In general, the surface strand layers contributed to the MOR and MOE. The parallel MOR and MOE values were the largest for the single layered S panel (only Slayers: S1), but the perpendicular MOR and MOE was the smallest. Perpendicular MOR and MOE were the largest for seven layered composite that had two cross oriented strand layers (SPSPSPS: SP7). Specimens retained more than half of their MOE and MOR after two hours in boiling water and one hour soaking. IB was the largest for the panel having only P layers, however, differences in IB strength were not identified among the other multi-layered composite panels thus the effect of layer construction on IB strength was small. Thickness swelling (TS) and surface roughness were smaller for the composite having P layers on the surface than for those having S layers. The addition of strands did not enhance the mechanical properties (MOR, MOE, IB). TS values for the panels, with which the S/P ratio was over than 1:1, was the similar to the value for the single layered S panels.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.6
• /
• pp.544-550
• /
• 2013

Tests were carried out on commercial particleboards manufactured in Korea to evaluate and modify formulas which had previously been developed to predict the holding loads of screw on the face and edge of specimen. Screw sizes were No. 6, 8 and 10 used in this study. The withdrawal loads of screws were developed to predict as a function of screw diameter, depth of penetration, specific gravity and IB of particleboard. Predicted equations were fitted to the test results of different length of No. 8 screws. Results of tests indicate that IB is a better predictor of holding loads on the face of particleboard than SG. On the other hand, SG is a good indicator of holding load on the edge of particleboard.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.127-131
• /
• 1997

In systematic and orderly estimation of fatigue strength of the spot welded lap joints, because the influence of residual stress of fatigue crach initiation and growth is not negligible, there need to estimate fatigue strength considered residual stress at near spot weld part of the lap joints. Therefore, in this thesis, peformed stress distribution and residual stress analysis at near the spot weld part by F.E.M and X-ray diffraction method, and obtained the maximum principal stress considered residual stress at nugget edge by superposing residual stress at nugget edge by superposing their results. From the results obtained above, we could find that fatigue strength of the IB-type spot welded lap joints was rearranged by the maximum principal stress considered residual stress at nugget edge and was entirely low about 13 percents compare with that neglected residual stress.

• Applied Biological Chemistry
• /
• v.41 no.1
• /
• pp.23-30
• /
• 1998

The cryIB, truncated cryIB$[cryIB({\alpha})]$, cryIA(b), and cytA genes, encoding 135-, 89-, 131-, and 27-kDa proteins, respectively, from Bacillus thuringiensis were cloned into a shuttle vector pBES and expressed in E. coli and Bacillus species. The morphology and solubility in alkaline buffer of the insecticidal crystal proteins were investigated. Transformation of intact cells of E. coli and Bacillus species was achieved by electroporation. High field strength of 11.0 kV/cm and resistance of 129 ohms were required for efficient transformation of E. coli strains and 4.5 kV/cm and 48 ohms for Bacillus species. Strains of recombinant E. coli and Bacillus species produced the insecticidal crystal proteins and accumulated as the same bipyramidal and irregular structures as those of CryIB and IA(b) and CytA of B. thuringiensls, respectively. The insecticidal crystal proteins accumulated in recombinant E. coli wire smaller in size than those in recombinant Bacillus species. The solubility in alkaline buffer of the insecticidal crystal proteins of recombinant E. coli increased gradually as the pH increased, whereas in the case of Bacillus species the solubility increased gradually as the pH increased up to 9 and then the solubility increased greatly up to two times higher than that of E. coli proteins.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.1
• /
• pp.22-31
• /
• 2020

In this study, rice straw and bagasse are used as raw materials to produce binderless particleboard (BPB). This study aims to evaluate the mechanical and physical properties of BPB. We identify the raw material that would be better for the production of BPB from the viewpoint of their basic properties. The BPBs are made from rice straw, bagasse, and combinations of both in ratios of 50:50 and 40:60, respectively. The modulus of elasticity (MOE), modulus of rupture (MOR), internal bonding (IB) strength, water absorption, and thickness swelling properties of the different BPBs are determined and compared. Results showed that all the properties are significantly influenced by the type of particles or particle combinations in the BPB. BPBs made from bagasse alone have the highest MOR, MOE, and IB mean values, whereas BPBs made from rice straw alone exhibit the lowest MOR, MOE, and IB values. Meanwhile, BPBs made from a combination of rice straw and bagasse at 40:60 ratio by weight have the second highest values for properties such as MOR, MOE, and IB, followed by BPBs made from a combination of rice straw and bagasse at 50:50 ratio by weight.

• Restorative Dentistry and Endodontics
• /
• v.40 no.1
• /
• pp.37-43
• /
• 2015

Objectives: Some antioxidants are believed to restore dentin bond strength after dental bleaching. This study was done to evaluate the influence of antioxidants on the bond strength of bleached bovine dentin. Materials and Methods: Thirty incisors were randomly assigned to 10 groups (two unbleached control and eight bleached groups:immediate bonding IB, 4 wk delayed bonding DB, 10% sodium ascorbate treated SA, 10% ${\alpha}$-tocopherol treated TP groups). Teeth in half of groups were subjected to thermal stress, whereas the remaining groups were not. Resin-dentin rods with a cross-sectional area of $2.25mm^2$ were obtained and microtensile bond strength was determined at a crosshead speed of 1 mm/min. Fifteen specimens were prepared for SEM to compare the surface characteristics of each group. The change in dentin bond strength from thermal stress and antioxidant treatment was evaluated using two-way analysis of variance (ANOVA) and Sheffe's post hoc test at a significance level of 95%. Results: The control group exhibited the highest bond strength values, whereas IB group showed the lowest value before and after thermocycling. The DB group recovered its bond strength similar to that of the control group. The SA and TP groups exhibited similar bond strength values with those of the control and DB groups before thermocycling. However, The TP group did not maintain bond strength with thermal stress, whereas the SA group did. Conclusions: Applying a 10% sodium ascorbate solution rather than 10% ${\alpha}$-tocopherol solution for 60 sec is recommended to maintain dentin bond strength when restoring non-vitally bleached teeth.