• Tribology and Lubricants
• /
• 제34권1호
• /
• pp.1-8
• /
• 2018

This paper presents the analysis of friction master curves for a sliding elastomer on rough granite. The hysteresis friction is calculated using an analytical model that considers the energy spent during the local deformation of the rubber due to surface asperities. The adhesion friction is also considered for dry friction prediction. The viscoelastic modulus of the rubber compound and the large-strain effective modulus are obtained from dynamic mechanical analysis (DMA). We accurately demonstrate the large strain of rubber that contacts with road substrate using the GW theory. We found that the rubber block deforms approximately to 40% strain. In addition, the viscoelastic master curve considering nonlinearity (at 40% strain) is derived based on the above finding. As viscoelasticity strongly depends on temperature, it can be assumed that the influence of velocity on friction is connected to the viscoelastic shift factors gained from DMA using the time-temperature superposition. In this study, we apply these shift factors to measure friction on dry granite over a velocity range for various temperatures. The measurements are compared to simulated hysteresis and adhesion friction using the Kluppel friction theory. Although friction results in the low-speed band match well with the simulation results, there are differences in the predicted and experimental results as the velocity increases. Thus, additional research is required for a more precise explanation of the viscoelastic material properties for better prediction of rubber friction characteristics.

• 한국지반공학회논문집
• /
• 제33권6호
• /
• pp.37-48
• /
• 2017

불포화 지반의 전단강도와 투수계수 산정에 이용되는 함수특성곡선은 건조과정과 습윤과정으로 나뉘며, 동일한 체적함수비에서 다른 흡수력을 나타내는 이력현상을 보인다. 강우 침투시 불포화 지반의 현장 거동은 습윤과정에 가깝게 발생하므로 수치해석 시에 습윤과정이 적용되어야 한다. 하지만 습윤과정이 건조과정보다 습득하는 시간이 오래 걸리기 때문에 주로 건조곡선이 사용되고 있다. 이를 보완하기 위해 건조곡선으로 습윤곡선을 추정하는 방법이 연구되어 왔으나, 방법이 복잡하고 잘 맞지 않는다. 따라서, 본 연구에서는 기존 자료를 바탕으로 습윤곡선 추정이 가능한 간편법을 제안하고 적용성을 검토하였다.

• Journal of Electrical Engineering and Technology
• /
• 제8권6호
• /
• pp.1409-1414
• /
• 2013

A new calculation method for iron loss coefficients is proposed by using the Steinmetz equation from Epstein data. The hysteresis loss must have linear characteristic according to the frequency. However, the existing iron loss coefficients are defined by formula of frequency. In this case, the hysteresis loss has non-linear characteristics by frequency. So, in this paper, the iron loss coefficients were defined by a function of the magnetic flux density, and the iron loss calculation is applied for Interior Permanent Magnet Synchronous Motor(IPMSM) of 600(W) and 200(W). The iron loss calculation results and the experimental results are compared according to the various materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.1.1-4
• /
• 1995

In this study, PLZT thin films in AFE region prepared by sol-gel processing were investigated. And PLZT stock solutions were spin-coated on ITO-glass. The PLZT thin films were annealed by RTA. Hysteresis curves, dielectric characteristics and optical transmittances were measured in order to investigates the characteristics far the thin films. The PLZT thin films were crystallized at 750$^{\circ}C$ for 5 mimutes by RTA and the rosette structure composed of perovskite observed in the thin films. In case La content was 2/90/10 antiferroelectric-ferroelectric phase boundary was 2/90/10 PLZT thin film, and its hysteresis curve was good for application of optical information storage.

• 전기화학회지
• /
• 제21권2호
• /
• pp.21-27
• /
• 2018

본 총설에서는 최근 전세계적으로 각광 받고 있는 유기 금속 할라이드 페로브스카이트 소재에서 일어나는 이온 이동 현상에 대한 최신 연구에 대해 정리하였다. 페로브스카이트 물질 조성, 인가전압에 따라 다른 결과들이 보고되었지만, 실제 태양전지 작동 조건에서 iodide 가 이동하는 것으로 보이며, 때로는 methylammonium의 이동도 관찰된다. 페로브스카이트는 상온에서 전자와 이온이 동시에 이동하는 이른바 mixed conductor이고, 이는 페로브스카이트 태양전지 전류-전압곡선의 hysteresis, 장시간 작동에 따른 성능 저하 등에 지대한 영향을 미친다.

• 조명전기설비학회논문지
• /
• 제28권4호
• /
• pp.21-28
• /
• 2014

Daily use characteristics of apparent power supplied to distribution transformer can be separated into two different time zone of waking hours and sleeping hours. In sleeping hours, using amount of power is decreasing. The actual curve of power seemed to be quite similar to this kind of separation. Inserting a condenser into a circuit in each different time zone led to maximize power factor of the transformer. The compensating condenser's on/off time is controlled by hysteresis circuit utilizing op amp and power factor of the transformer was improved from 0.945 to 0.999. As a result, the average of current reduction was 2.53A per hour of transformer.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권2호
• /
• pp.165-170
• /
• 2013

This paper presents the iron loss prediction of rotating electric machines taking account of the vector hysteretic properties of electrical steel sheet. The E&S vector hysteresis model is adopted to describe the vector hysteretic properties of a non-oriented electrical steel sheet, and incorporated into finite element analysis (FEA) for magnetic field analysis and iron loss prediction. A permanent magnet synchronous generator is taken as a numerical model, and the analyzed magnetic field distribution and predicted iron loss by using the proposed method is compared with those from a conventional method which employs an empirical iron loss formula with FEA based on a non-linear B-H curve. Through the comparison the effectiveness of the presented method for the iron loss prediction of the rotating machine is verified.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.463-464
• /
• 2017

다른 리튬계열 전지와 달리, 인산철($LiFePO_4$) 배터리는 중간 동작 영역에서 개방전압(OCV; open-circuit voltage)의 히스테리시스(hysteresis) 영역이 존재한다. 그러므로, 인산철 배터리 관리시스템, 특히 충전상태(SOC; state-of-charge)와 수명상태(SOH; state-of-health)의 정확한 모니터링을 위해서는 OCV의 정밀성이 요구된다. 본 논문에서는, 충전 및 방전 OCV-SOC의 SOC 간격에 따른 인산철 배터리의 SOH를 비교하기 위해 전기적 등가회로 모델(ECM; electrical-circuit modeling)적응제어 알고리즘 기반 실시간 내부저항(DCIR; direct current internal resistance)을 모니터링 하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.224-227
• /
• 1999

Ferroelectric Pb(Zr$\sub$0.52/Ti$\sub$0.48/)O$_3$ thin films were fabricated by pulsed laser deposition, mainly varying process conditions such as substrate temperature, oxygen pressure, and laser energy, PZT films annealed at more than 600$^{\circ}C$ were crystallized into pure perovskite phases regardless of deposition temperatures. Lower deposition temperature of 400$^{\circ}C$ accompanied with post-annealing at 650$^{\circ}C$ resulted in denser microstructures with extremely small grains compated to those of thin films annealed at higher deposition temperatures. Hysteresis curves of thin film with small grains exhibitied good squareness and low leakage characteristics.

• Steel and Composite Structures
• /
• 제24권6호
• /
• pp.741-751
• /
• 2017

A steel slit shear wall has vertical slits and when it is under lateral loads, the section between these slits has double-curvature deformation, and by forming a flexural plastic hinge at the end of the slit, it dissipates the energy on the structure. In this article, Experimental, numerical and analytical analyses are performed to study the effect of slit shape and edge stiffener on the behavior of steel slit shear wall. Seismic behavior of three models with different slit shapes and two models with different edge stiffener shapes are studied and compared. Hysteresis curves, energy dissipation, out of plane buckling, initial stiffness and strength are discussed and studied. The proposed slit shape reduces the initial stiffness, increases the strength and energy dissipation. Also, edge stiffener shape increases the initial stiffness significantly.