• 공업화학
• /
• 제28권1호
• /
• pp.118-124
• /
• 2017

공랭식 고분자전해질 연료전지는 개방된 cathode구조로 인하여 시스템의 단순화와 부품 수 저감의 장점이 있다. 공랭식 연료전지는 최근에 많이 연구되고 있지만, 성능이 외부 환경에 영향을 받으며, 공기의 상대습도가 낮은 경우 전해질막의 건조로 인한 성능 감소가 발생할 수 있다. 본 연구에서는 공랭식 연료전지의 성능에 영향을 주는 요인인 cathode 측 공기 유량과 anode 측 purge interval영향에 대해 분석하였으며, 스택을 운전하지 않는 상태로 장기간 보관하는 것이 성능에 미치는 영향에 대하여 실험을 수행하였다. 연료전지 외부에 설치한 fan의 전압을 조절하면 cathode 측 공기의 공급유량을 변화시킬 수 있고 스택의 온도도 제어할 수 있으므로, fan전압은 공랭식 연료전지의 성능에 영향을 주는 중요한 인자이다. 연료전지 시스템을 단순화하고 수소의 사용률을 높이기 위하여 anode 측은 dead ended anode (DEA) 기법을 사용하였다. 주기적인 purge를 실행하여 생성된 물과 가스를 배출하였으며, purge 주기를 변경하면서 스택의 성능에 미치는 영향에 대하여 실험을 수행하였다. 스택의 보관기간이 길어질수록 membrane dehydration으로 인해 성능이 감소하는 것을 실험을 통해 파악하였고, 단시간에 성능을 회복할 수 있는 기법을 제시하였다.

• Elastomers and Composites
• /
• 제51권2호
• /
• pp.147-153
• /
• 2016

Polyvinyl chloride (PVC) has been used as a general-purpose polymer because of its lower cost, good durability and mechanical properties compared to other materials. However, PVC is vulnerable to heat deformation and generates a toxic gas like hydrogen chloride. Therefore, it is important to delay or prevent the flame retardancy and thermal degradation of the PVC during the processing. It was reported that aluminum trihydroxide (ATH) improved flame retardancy as well as smoke inhibition of the virgin polymer. In this study, PVC composites by addition of ATH were compounded in a modular intermeshing co-rotating twin screw extruder. The PVC composites with different concentrations of ATH (0~5 phr) were analyzed. Flame retardancy of the PVC composite significantly increased depending on the ATH concentration. LOI of the composite also increased with the concentration of ATH. There were no significant differences for the thermal properties of the PVC composites with ATH.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.55.2-55.2
• /
• 2012

Intensive theoretical and experimental studies have been carried out at Korean Institute of Science and Technology (KIST) on controlling the bio absorbing rate of the Mg alloys with high mechanical strength through tailoring of electrochemical potential. Key technology for retarding the corrosion of the Mg alloys is to equalize the corrosion potentials of the constituent phases in the alloys, which prevented the formation of Galvanic circuit between the constituent phases resulting in remarkable reduction of corrosion rate. By thermodynamic consideration, the possible phases of a given alloy system were identified and their work functions, which are related to their corrosion potentials, were calculated by the first principle calculation. The designed alloys, of which the constituent phases have similar work function, were fabricated by clean melting and extrusion system. The newly developed Mg alloys named as KISTUI-MG showed much lower corrosion rate as well as higher strength than previously developed Mg alloys. Biocompatibility and feasibility of the Mg alloys as orthopedic implant materials were evaluated by in vitro cell viability test, in vitro degradation test of mechanical strength during bio-corrosion, in vivo implantation and continuous observation of the implant during in vivo absorbing procedures. Moreover, the cells attached on the Mg alloys was observed using cryo-FIB (focused ion beam) system without the distortion of cell morphology and its organ through the removal of drying steps essential for the preparation of normal SEM/TEM samples. Our Mg alloys showed excellent biocompatibility satisfying the regulations required for biomedical application without evident hydrogen evolution when it implanted into the muscle, inter spine disk, as well as condyle bone of rat and well contact interface with bone tissue when it was implanted into rat condyle.

• 대한화학회지
• /
• 제7권2호
• /
• pp.96-105
• /
• 1963

The weight decrease curves of 18 kinds of polymers have been measured by thermobalance at the same condition where temperature is increased $1^{\circ}C$ per minutes under nitrogen or air atmosphere. The curves are further differentiated to obtain rate curve of weight decrease. Those curve offer a method to compare relative thermal stability, effects of oxygen or modes of thermal degradation of polymers qualitatively. The curves could be classified into following four types: Polystyrene, polymethylmethacrylate and acetal polymer belong to the first type. Those polymers depolymerize mainly into corresponding monomers, weight decrease curves are steepy up to perfect vaporization of polymers and rate curves show a relatively sharp peak. (Type I) Polyvinyl chloride represents the second type. This polymer decomposes with splitting off of hydrogen chloride. The thermogravimetric curve rises rapidly at first, then level off at the moderate weight decrease and gradually rises. Polyvinyl acetate also belongs to this class. (Type II) The modification of the second type is represented by polyester. The curve at the early stage is less steep, the leveling off at the next stage is less clear and the final rising of the curve is steeper than the normal second type. Polyamide, polyurethane, and polycarbonate belong to this type. (Type II') The thermal decomposition of the third type polymers is more complex than that of others. Various irregular chain scissions including side chain splitting and depolymerization to monomers occur simultaneously. The weight of the polymer decreases gradually and the rate curve does not show sharp peaks. Polyvinyl alcohol and diene polymers belong to this type. (Type III) Generally, polycondensation polymers are more stable toward heat than addition polymers and polymers having aromatic nucleus show good thermal stability. Polymers having tertiary carbon atoms such as polystyrene or polypropylene and acetal resin start decomposition under airatmosphere at the temprature below $50^{\circ}C$ or more of the temperature where the polymers start decomposition under nitrogen atmosphere.

• ETRI Journal
• /
• 제31권6호
• /
• pp.660-666
• /
• 2009

We investigate the effects of interfacial dielectric layers (IDLs) on the electrical properties of top-gate In-Ga-Zn-oxide (IGZO) thin film transistors (TFTs) fabricated at low temperatures below $200^{\circ}C$, using a target composition of In:Ga:Zn = 2:1:2 (atomic ratio). Using four types of TFT structures combined with such dielectric materials as $Si_3N_4$ and $Al_2O_3$, the electrical properties are analyzed. After post-annealing at $200^{\circ}C$ for 1 hour in an $O_2$ ambient, the sub-threshold swing is improved in all TFT types, which indicates a reduction of the interfacial trap sites. During negative-bias stress tests on TFTs with a $Si_3N_4$ IDL, the degradation sources are closely related to unstable bond states, such as Si-based broken bonds and hydrogen-based bonds. From constant-current stress tests of $I_d$ = 3 ${\mu}A$, an IGZO-TFT with heat-treated $Si_3N_4$ IDL shows a good stability performance, which is attributed to the compensation effect of the original charge-injection and electron-trapping behavior.

• 한국결정성장학회지
• /
• 제24권1호
• /
• pp.41-45
• /
• 2014

다양한 공정 조건으로 $SiN_x$와 $SiO_2$ 박막을 형성하고 이에 대한 패시베이션 특성에 대한 연구를 수행하였다. Plasma enhanced chemical vapor deposition(PECVD)을 이용하여 증착된 $SiN_x$ 박막의 경우, 증착 두께가 증가함에 따라 페시베이션 특성이 향상되는 것을 관찰하였다. 이는 PECVD 증착 공정 중 유입되는 수소 원자들이 실리콘 표면에 존재하는 Dangling bond와 결합하여 소수 캐리어의 재결합 현상을 효과적으로 감소시켰기 때문이다. 건식 산화법으로 형성된 $SiO_2$ 박막은 습식 산화법으로 형성된 것 보다 치밀한 계면 구조를 가짐으로 인하여 약 20배 이상 우수한 패시베이션 특성을 나타내었다. 건식 산화 공정 온도가 증가함에 따라 패시베이션 특성이 열화되는 현상이 발생하였고, Capacitance-voltage(C-V) 및 Conductance-voltage(G-V) 분석을 통하여 $SiO_2$/실리콘 계면에 존재하는 계면 결함 밀도 증가에 의해 나타나는 현상임을 알 수 있었다.

• 한국미생물·생명공학회지
• /
• 제31권4호
• /
• pp.413-420
• /
• 2003

축산폐기물의 퇴비화에 사용된 혼합 미생물을 이용해서 음식쓰레기 처리 과정에서 발생되는 악취를 효과적으로 처리 하고자 하였다. 시판되는 가정용 음식쓰레기 처리기를 사용하여 음식쓰레기의 퇴비화와 악취저강 특성을 조사하였다. 퇴비화는 10일 경과후부터 인정화되었으며, 혼합 미생물을 첨가한 경우 온도와 pH가 혼합 미생물을 첨가하지 않은 것과 비교해 더 빨리 증가하였으며, 퇴비화의 지표 중에 하나인 전기전도도 (Conductivity)도 1.2 에서 2.4 mS/cm로 혼합 미생물을 첨가하지 않은 경우의 1.3 mS/cm 보다 급격한 상승을 보였다. 식품쓰레기 처리 중에 발생되는 악취 물질, 즉 황화수소와 저급지방산은 8 일 동안에 각각90-100％와 70-80％로 효과적으로 제거되었다. 또한 알칼리 상태와 고온의 조건에서 성장하는 미생물이 퇴비화 과정 중에 우점 하였으며, Bacillus cereus No. 15 균주가 혼합 미생물 중 효과적인 식품쓰레기처리와 악취제거에 관여하고 있다는 사실을 증명하였다.

• 방사선산업학회지
• /
• 제5권3호
• /
• pp.253-258
• /
• 2011

Acetylsalicylic acid (ASA) has been issued recently in contaminated water environments because of potential impacts on ecosystem and public health. This study was aimed at investigating the possibility of ASA degradation using gamma ray irradiation. In addition, the use of sodium persulfate, hydrogen peroxide, ferrous sulfate were tested in order to examine a synergistic effect with gamma ray. The absorbed dose was ranged from 0.2 to 10 kGy and the concentration of oxidants were from 0.1 to 10 mM in this study. The concentration of ASA was gradually decreased corresponding to the increase of the absorbed dose. When soudium persulfate was simultaneously applied, most of the parent compound was completely degraded even at a low dose of 0.8 kGy. The removal efficiency of total organic carbon was 90% even at the highest dose of 10 kGy without sodium persulfate. However, the efficiency was dramatically enhanced up to 98% at the same dose by adding 10 mM of oxidants. It was suggested that hydroxyl radical ($OH{\cdot}$) and sulfate radical ($SO{_4}^-{\cdot}$) were formed in the system and made roles in degrading ASA at the same time.

• Korean Chemical Engineering Research
• /
• 제59권1호
• /
• pp.6-10
• /
• 2021

PEMFC(Proton Exchange Membrane Fuel Cell) 고분자 막의 shorting 저항(Shorting Resistance, SR)은 고분자 막의 내구성에 관한 중요한 지표다. SR이 감소하면 shorting 전류(Shorting Current, SC)가 증가하여 내구성과 성능이 감소하고, SR이 약 0.1 kΩ·㎠ 이하가 되면 shorting이 발생하여 온도가 급상승하고 MEA(Membrane Electrode Assembly)를 연소시켜 스택 구동이 종료된다. Shorting 현상을 방지하기 위해서는 SR을 제어해야 하므로 SR에 영향을 주는 조건들에 대해서 연구하였다. SR 측정방법들에서도 차이가 있어서 DOE(Department of Energy)와 NEDO(New Energy and Industrial Technology Development Organization) 방법을 개선한 SR 측정법을 제시하였다. 상대습도와 온도, 셀 체결 압이 상승하면 SR이 감소함을 확인하였다. 고분자 막의 가속내구 평가과정에서 마지막 단계에서 SR이 0.1 kΩ·㎠ 이하로 급감해 수소투과전류밀도가 15 mA/㎠ 이상이 되었고, 이 MEA를 해체 후 SEM(Scanning Electron Microscope) 분석한 결과 고분자 막 내부에 백금이 많이 분포함을 보였다.

• Journal of the Korean Wood Science and Technology
• /
• 제50권4호
• /
• pp.283-298
• /
• 2022

Wood has always been used for various day-to-day applications such as interior or exterior construction materials, and household products. However, it can undergo photodegradation and discoloration by environmental factors including ultraviolet (UV) light, and thus has shortened its service life. Bleaching or delignification of wood surfaces is a suitable solution to stabilize wood against weathering by UV because these techniques can alter or remove the chromophores in lignin, which is a main factor of wood discoloration. To improve the color stability of wood surface according to the lifespan, surface delignification was conducted using peracetic acid (PAA) and hydrogen peroxide (HP) on the woods of Larix kaempferi and Quercus mongolica. After the PAA treatment, L^* increased considerably from 60-70 to 90-95. Furthermore, wood surface color did not change significantly after UV exposure. The color differences (𝜟E^*) between before and after PPA treatment of wood showed the 4.8-12.2 of L. kaempferi, and 1.7-3.7 of Q. mongolica, respectively. The lignin-related peaks in Fourier transform infrared spectroscopy (FT-IR) spectra disappeared with increased duration of PAA treatment. These results confirmed that the lignin component was partially or completely removed after the PAA treatment; the color differences (𝜟E^*) clearly showed that there was a reduction in redness (a^*) and yellowness (b^*), and an increase in lightness (L^*) owing to the removal of lignin. Based on these results, this study demonstrated that the partial removal of lignin from wood surfaces is a fundamental method for resolving photo-degradation.