• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.259-263
• /
• 2012

Dependence of the freeze-drying process condition on microstructure of porous W and pore formation mechanism were studied. Camphene slurries with $WO_3$ contents of 10 vol% were prepared by milling at $50^{\circ}C$ with a small amount of dispersant. Freezing of a slurry was done in Teflon cylinder attached to a copper bottom plate cooled at $-25^{\circ}C$. Pores were generated subsequently by sublimation of the camphene during drying in air for 48 h. The green body was hydrogen-reduced at $800^{\circ}C$ for 30 min, and sintered in the furnace at $900^{\circ}C$ for 1 h. After heat treatment in hydrogen atmosphere, $WO_3$ powders were completely converted to metallic W without any reaction phases. The sintered samples showed large pores with the size of about $70{\mu}m$ which were aligned parallel to the camphene growth direction. Also, the internal wall of large pores and near bottom part of specimen had relatively small pores with dendritic structure due to the growth of camphene dendrite depending on the degree of nucleation and powder rearrangement in the slurry.

• 한국세라믹학회지
• /
• 제50권6호
• /
• pp.485-488
• /
• 2013

A SiC-$CeO_2$ composite membrane was successfully fabricated using an ally-hydridopolycarbosilane (AHPCS) binder and treated by dip-coating at 60 times with a $CeO_2$ sol solution. The dip-coated SiC membrane was calcined at 773 K and then sintered at 1173 K under an air atmosphere. The coated membrane was characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and a BET surface analysis. The difference in permeation performance between $H_2$ and CO gases was measured by varying the temperature. The permeation flux of $H_2$ on the SiC membrane with layered $CeO_2$ was obtained as $8.45{\times}10^{-6}\;mol/m^2sPa$ at room temperature. The CO permeation flux was $2.64{\times}10^{-6}\;mol/m^2sPa$ at room temperature. The reaction enthalpy (${\Delta}H^{\circ}$) for the hydrogen permeation process was calculated as -7.82 J/mol by Arrhenius plots.

• 한국분말재료학회지
• /
• 제15권2호
• /
• pp.107-113
• /
• 2008

Ultrafine TiC-5%Co powders were synthesized by spray drying of aqueous solution of TiO$(OH)_2$ slurry and cobalt nitrate, followed by calcination and carbothermal reaction. The oxide powders with carbon powder was reduced and carburized at $900^{\circ}C{\sim}1250^{\circ}C$ under hydrogen atmosphere. During reduction, CO gas was mainly evolved by reducing reaction of oxides. Ultrafine TiC-5%Co powders were easily formed by carbothermal reaction at $1250^{\circ}C$ due to using ultrafine powders as raw materials. The ultrafine WC-TiC-Co alloy prepared by sintering of mixed powder of ultrafine WC-13%Co powder and ultrafine TiC-5%Co powder has higher sintered density and mechanical properties than WC-TiC-Co alloy prepared by commercial WC, TiC and Co powders.

• 마이크로전자및패키징학회지
• /
• 제27권4호
• /
• pp.11-17
• /
• 2020

Copper has been proved to be the best catalyst for electrochemical CO2 reduction reaction, however, for optimal efficiency and selectivity, its performance requires improvements. Electrochemical CO2 reduction reaction (RR) using CuO nanowire electrode was performed with different concentrations of KHCO3 electrolyte (0.1 M, 0.5 M, and 1 M). Cu(OH)2 was formed on Cu foil, followed by thermal-treatment at 200℃ under the air atmosphere for 2 hrs to transform it to the crystalline phase of CuO. We evaluated the effects of different KHCO3 electrolyte concentrations on electrochemical CO2 reduction reaction (RR) using the CuO nanowire electrode. At a constant current (5mA), low concentrated bicarbonate exhibited a more negative potential -0.77 V vs. Reversible Hydrogen Electrode (RHE) (briefly abbreviated as VRHE), while the negative potential reduced to -0.33 VRHE in the high concentration of bicarbonate solution. Production of H2 and CH4 increased with an increased concentration of electrolyte (KHCO3). CH4 production efficiency was high at low negative potential whereas HCOOH was not influenced by bicarbonate concentration. Our study provides insights into efficient, economically viable, and sustainable methods of mitigating the harmful environmental effects of CO2 emission.

• 한국세라믹학회지
• /
• 제39권4호
• /
• pp.367-376
• /
• 2002

$SrZr_{1-x}Y_xO_{3-\delta}$(x=0.05, 0.10)-금속전극 계에서 임피던스법과 d.c.법으로 전기전도도를 측정함으로써 고체전해질 및 전극전도도를 고찰하였다. 고체전해질과 anode를 통한 전기전도도는 $P_W^{1/2}$(PW는 수증기분압)에 의존하여 증가함을 보였다. Cathode 전도도는 $P_{O2}^{1/4}$에 비례함을 보였으며, 수증기분압 증가와 함께 감소하여 고체전해질내의 전자 결함의 농도와 함께 증가하는 것을 알 수 있었다. 수소분위기에서는 수증기의 첨가가 anode와 cathode 두 방향의 전극반응 속도 모두를 촉진하였다. 도펀트 첨가량이 5%에서 10%로 증가될 때 anode와 고체전해질의 전기전도도가 3배 이상 크게 증가하여 유효 산소이온공공의 농도가 급격히 증가함을 알 수 있었다. Pt와 Ag전극을 통한 cathode 전도도의 활성화에너지가 거의 같은 값을 나타냈으며 이는 cathode반응의 속도가 금속전극이 아니라 고체전해질표면에서 일어나는 반응에 의하여 결정되는 것으로 해석되었다.

• 한국분말재료학회지
• /
• 제26권5호
• /
• pp.410-414
• /
• 2019

The hydrogen reduction behavior of the $CuO-SCo_3O_4$ powder mixture for the synthesis of the homogeneous Cu-15at%Co composite powder has been investigated. The composite powder is prepared by ball milling the oxide powders, followed by a hydrogen reduction process. The reduction behavior of the ball-milled powder mixture is analyzed by X-ray diffraction (XRD) and temperature-programmed reduction at different heating rates in an Ar-10%H2 atmosphere. The scanning electron microscopy and XRD results reveal that the hydrogen-reduced powder mixture is composed of fine agglomerates of nanosized Cu and Co particles. The hydrogen reduction kinetics is studied by determining the degree of peak shift as a function of the heating rate. The activation energies for the reduction of the oxide powders estimated from the slopes of the Kissinger plots are 58.1 kJ/mol and 65.8 kJ/mol, depending on the reduction reaction: CuO to Cu and $SCo_3O_4$ to Co, respectively. The measured temperature and activation energy for the reduction of $SCo_3O_4$ are explained on the basis of the effect of pre-reduced Cu particles.

• 에너지공학
• /
• 제19권4호
• /
• pp.215-220
• /
• 2010

근래의 무분별한 화석연료의 사용은 에너지자원의 고갈과 환경오염의 문제를 야기하여 이의 해결을 위한 청정신에너지에 대한 연구가 전 세계적으로 집중되고 있다. 이 중 바이오매스는 화석연료보다 비교적 높은 H/C비를 갖기 때문에 신에너지인 수소 또는 Syngas를 생산하기 위한 가스화 특성이 우수한 특징을 가지고 있으며, 구성성분 내 중금속, 타르 질소를 거의 함유하지 않는 점에서 환경오염 저감과 동시에 대체 신에너지로써 각광을 받고 있다. 본 연구에서는 목질계 바이오매스인 Wood pellet에 대하여 고정층 반응기를 이용하여 질소 분위기하에서 온도 및 Steam/Biomass Ratio(SBR)조건 변화에 따른 가스화 특성으로 고찰하는데 그 목적을 둔다. 온도의 영향에 대하여, 높은 온도 범위에서 수소 수율이 증가함을 알 수 있었다. SBR에 대한 영향으로서, 상대적 저온 조건에서는 SBR이 1 이상인 조건에서는 수소 수율이 거의 일정한 경향을 보였고, $900^{\circ}C$의 고온에서는 SBR 증가에 따라 증가하는 결과를 얻었다. 또한 $H_2$/CO ratio에 비하여 $H_2/CH_4$ ratio의 변화가 더 큰 결과로부터, 본 실험 조건에서의 반응은 Steam reforming이 Water gas shift reaction 보다 더욱 지배적임을 확인하였다. 최적의 $H_2$ 수율 생산 조건은 열분해의 경우 $800^{\circ}C$이며, 저온 스팀가스화의 경우에는 SBR=1, $900^{\circ}C$의 고온인 경우에는 SBR=3 이었으며, 최대 수소 수율은 $900^{\circ}C$, SBR=3의 조건에서 38.5 vol.%(56.01 L/min kg) 이었다.

• 한국분말재료학회지
• /
• 제22권4호
• /
• pp.266-270
• /
• 2015

The synthesis of NiTi alloy powders by hydrogen reduction and dehydrogenation process of NiO and $TiH_2$ powder mixtures is investigated. Mixtures of NiO and $TiH_2$ powders are prepared by simple mixing for 1 h or ball milling for 24 h. Simple-mixed mixture shows that fine NiO particles are homogeneously coated on the surface of $TiH_2$ powders, whereas ball milled one exhibits the morphology with mixing of fine NiO and $TiH_2$ particles. Thermogravimetric analysis in hydrogen atmosphere reveals that the NiO and $TiH_2$ phase are changed to metallic Ni and Ti in the temperature range of 260 to $290^{\circ}C$ and 553 to $639^{\circ}C$, respectively. In the simple-mixed powders by heat-up to $700^{\circ}C$, agglomerates with solid particles and solidified liquid phase are observed, and the size of agglomerates is increased at $1000^{\circ}C$. From the XRD analysis, the presence of liquid phase is explained by the formation and melting of $NiTi_2$ inter-metallic compound due to an exothermic reaction between Ni and Ti. The simple-mixed powders, heated to $1000^{\circ}C$, lead to the formation of NiTi phase but additional Ni-, Ti-rich and Ti-oxide phases. In contrast, the microstructure of ball-milled powders is characterized by the neck-grown particles, forming $Ni_3Ti$, Ti-oxide and unreacted Ni phase.

• 전기화학회지
• /
• 제2권2호
• /
• pp.106-111
• /
• 1999

[ $CaNi_5$ ] 수소저장합금의 전기화학적 충$\cdot$방전 특성에 미치는 MG(mechanical grinding) 영향이 Ar및 $H_2$ 가스분위기에서 조사되었다 MG공정중 $CaNi_5$ 합금은 표면 산화층의 파괴와 재생성 및 산화층 근방의 불균질화로 인하여 MG 15시간 이후부터 CaO와 Ni로 뚜렷한 상분리가 일어났다. $MG-CaNi_5$는 MG시간이 길어질수록 초기의 전기화학적 방전용량은 현저히 감소하였지만 충$\cdot$방전 싸이클의 증가에 따른 용량저하 속도는 $CaNi_5$합금에 비하여 낮았다. MG처리된 $CaNi_5$합금의 퇴화는 MG공정중의 상분리 및 불규칙화에 의한 수소의 가역반응 site의 감소 및 분극저항의 증가, KOH 전해질 내에서 합금 표면의 산화반응에 의한 부동태 피막형성에 기인하는 것으로 판단되었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.134-134
• /
• 2010

Fuel cell is a device that directly converts chemical energy in the form of a fuel into electrical energy by way of an electrochemical reaction. In the anode for a high temperature fuel cell, nickel or nickel alloy has been used in consideration of the cost, oxidation catalystic ability of hydrogen which is used as fuel, electron conductivity, and high temperature stability in reducing atmosphere. Most MCFC stacks currently operate at an average temperature of $650^{\circ}C$. There is some gains with decreased temperature in MCFC to diminish the electrolyte loss from evaporation and the material corrosion, which could improve the MCFC life. However, operating temperature has a strong related on a number of electrode reaction rates and ohmic losses. Baker et al. reported the effect of temperature (575 to $650^{\circ}C$). The rates of cell voltage loss were 1.4mV/$^{\circ}C$ for a reduction in temperature from 650 to $600^{\circ}C$, and 2.16mV/$^{\circ}C$ for a decrease from 600 to $575^{\circ}C$. The two major contributors responsible for the change in cell voltage with reducing operation temperature are the ohmic polarization and electrode polarization. It appears that in the temperature range of 550 to $650^{\circ}C$, about 1/3 of the total change in cell voltage with decreasing temperature is due to an increase in ohmic polarization, and the electrode polarization at the anode and cathode. In addition, the oxidation reaction of hydrogen on an ordinary nickel alloy anode in MCFC is generally considered to take place in the three phase zone, but anyway the area contributing to this reaction is limited. Therefore, in order to maintain a high performance of the fuel cell, it is necessary to keep this reaction responsible area as wide as possible, that is, it is needed to keep the porosity and specific surface area of the anode at a high level. In this study effective anodes are prepared for low temperature MCFC capable of enhancing the cell performance by using zirconium hydride at least in part of anode material.