• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.737-743
• /
• 2016

Coastal hazards such as high waves are expected to increase due to global climate change. Therefore, we investigated new armor unit structures for disaster prevention. Recently, a concrete caisson has been used in many breakwaters against high waves in South Korea, but the demand for concrete armor unit has increased due to the high cost and many installation requirements. Though many new armor units have been developed over the world since Tetrapod in 1950, few have been used due to lack of systematical development. The representative armor units in current use have many advantages, but they cannot be applied to waves higher than 8 m. One of the new armor units developed by the design guide based on recent trend and hydraulic model experiments were conducted. The new armor unit was developed as a single layer due to cost effectiveness. However, the thickness is close to 1.5 times by overlapping the alphabet A and V. It showed higher overtopping compared to a double layer because of the thickness and the high packing density. It has a high interlocking vertically but low horizontally. It shows good stability at 9 m in model testing.

• Journal of Biosystems Engineering
• /
• v.43 no.1
• /
• pp.1-13
• /
• 2018

Purpose: The development of compact tractors that can be used in dry fields, greenhouses, and orchards for pest control, weeding, transportation, and harvesting is necessary. The development and performance evaluation of power transmission units are very important when it comes to tractor development. This study evaluates the performance of a driving power transmission unit of a 50 kW multi-purpose narrow tractor. Methods: The performance of the transmission and forward-reverse clutch, which are the main components of the driving power transmission unit of multi-purpose narrow tractors, was evaluated herein. The transmission performance was evaluated in terms of power transmission efficiency, noise, and axle load, while the forward-reverse clutch performance was evaluated in terms of durability. The transmission's power transmission efficiency accounts for the measurement of transmission losses, which occur in the transmission's gear, bearing, and oil seal. The motor's power was input in the transmission's input shaft. The rotational speed and torque were measured in the final output shaft. The noise was measured at each speed level after installing a microphone on the left, right, and upper sides. The axle load test was performed through a continuous equilibrium load test, in which a constant load was continuously applied. The forward-reverse clutch performance was calculated using the engine torque to axle torque ratio with the assembled engine and transmission. Results: The loss of power in the transmission efficiency test of the driving power unit was 6.0-9.7 kW based on all gear steps. This loss of horsepower was equal to 11-18% of the input power (52 kW). The transmission efficiency of the driving power unit was 81.5-89.0%. The noise of the driving power unit was 50-57 dB at 800 rpm, 70-77 dB at 1600 rpm, and 76-83 dB at 2400 rpm. The axle load test verified that the input torque and axle revolutions were constant. The results of the forward-reverse clutch performance test revealed that hydraulic pressure and torque changes were stably maintained when moving forward or backward, and its operation met the hydraulic design standards. Conclusions: When comprehensively examined, these research results were similar to the main driving power transmission systems from USA and Japan in terms of performance. Based on these results, tractor prototypes are expected to be created and supplied to farmhouses after going through sufficient in-situ adaptability tests.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.1
• /
• pp.11-17
• /
• 2014

In this study, a hydraulic model experiment under wave conditions was carried out to investigate the gap/distance between two near-unit farm lines that affects the rope kink and shape variation of a seaweed farm during mooring block movement. As a result, rope kink occurred during the low wave height condition as the gap/distance between the two near-unit farm lines decreased. The seaweed farm maintained a stable shape in the higher wave height conditions as the gap/distance between the two near-unit farm lines increased. This result indicates that rope kink is sensitively affected by the gap/distance between the two near-unit farm lines. A tendency to increase the critical wave height was observed when mooring block movement occurred, and as the mooring block weight and wave period increased. From the experimental results in which incident wave conditions and the mooring block weight changed, as the front side mooring block weight increased from 3.0 to 8.0 tons, the seaweed farm was stable, and rear side mooring block movement hardly occurred. The observed tension of the seaside mooring line was a maximum at about 3.0 ton/m.

• Journal of Korean Society on Water Environment
• /
• v.35 no.6
• /
• pp.497-509
• /
• 2019

After the Total Maximum Daily Loads(TMDLs) was applied, it became beyond the limit of concentration management. However, it does not adequately reflect the characteristics of various watersheds, and causes problems with local governments because of the standard flow set. Thus, in this study, the Han River system is organized into four groups in estimating the Pollution Contribution by applying the Flow Duration Curve(FDC) created by the daily flow of data from the HSPF. And the method of this study is expected to be valuable as basic data for the TMDLs. As a result, Group I contains the main watersheds with no large hydraulic structures and tributary watersheds. There is no specificity in the FDC and the Pollution Contribution is estimated as rainfall runoff. Group II contains watersheds near the city where the FDC is maintained above a certain level during the Low Flow Conditions and the Pollution Contribution is estimated as the discharge flow of large scale point pollution facilities. Group III contains the main watersheds in which the large hydraulic structures are installed and FDC is curved in the Low Flow Conditions. So the Pollution Contribution is estimated as the water quality of the large hydraulic structures. Group IV contains the upstream in mainstream watersheds in which the large hydraulic structures are installed and the FDC is disabled before the Low Flow Conditions. As the flow is concentrated in the High Flow Conditions, the non-point pollution sources are estimated as the Pollution Contribution.

• The Journal of Engineering Geology
• /
• v.28 no.1
• /
• pp.25-34
• /
• 2018

The physical properties and unsaturated characteristics of acid sulfate soils were investigated and analyzed. As the results of measuring physical properties of the acid sulfate soils obtained around the Ilkwang mine area, the dry unit weight is $1.246t/m^3$ and this soil is classified into the silty sand (SM) by USCS. Soil Water Characteristics Curves (SWCC) of the drying and wetting paths were measured by the automated SWCC apparatus. Also, Hydraulic Conductivity Functions (HCF) of the drying and wetting paths were estimated by the van Geunchten (1980) model which is the most well-known parameter estimation method. The hydraulic conductivity of acid sulfate soils in the dry path was continuously decreased with increasing the matric suction. However, the hydraulic conductivity in the wetting path was decreased relatively small with increasing matric suction and decreased suddenly just before water entry value of matric suction. Meanwhile, the hysteresis phenomenon was occurred in SWCCs and HCFs during the drying and wetting paths.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.65 no.1
• /
• pp.41-49
• /
• 2023

To utilize the hydraulic and hydrological models when simulating floods in agricultural watersheds, it is necessary to consider agricultural reservoirs, farmland, and farmland drainage system, which are characteristics of agricultural watersheds. However, most of them are developed individually by different researchers, also, each model has a different simulation scope, so it is hard to use them integrally. As a result, there is a need to link each hydraulic and hydrological model. Therefore, this study established an integrated flood simulation system for the comprehensive flood simulation of agricultural reservoir watersheds. The system can be applied easily to various watersheds because historical weather data and the SSP (Shared Socio-economic Pathways) climate change scenario database of ninety weather stations were built-in. Individual hydraulic and hydrological models were coded and coupled through Python. The system consists of multiplicative random cascade model, Clark unit hydrograph model, frequency analysis model, HEC-5 (Hydrologic Engineering Center-5), HEC-RAS (Hydrologic Engineering Center-River Analysis System), and farmland drainage simulation model. In the case of external models with limitations in conceptualization, such as HEC-5 and HEC-RAS, the python interpreter approaches the operating system and gives commands to run the models. All models except two are built based on the logical concept.

• The Journal of Engineering Geology
• /
• v.26 no.1
• /
• pp.15-22
• /
• 2016

Hydraulic falling head and slug tests were carried out in an alluvium aquifer using a borehole stability device. The hydraulic testing had proved difficult in alluvial formations of sands and gravels due to borehole collapse and unstable borehole walls within the test section. This study aims to improve the hydraulic test results by using a borehole stability device. The device can minimize the collapse of borehole walls, and the use of a filter with a constant opening ratio improves the calculations per unit area of the test section. Permeability obtained from the falling head test without a borehole stability device was 8.82 × 10⁻⁵m/sec. When the borehole stability device was installed in the same test section the measured permeability increased to 4.00 × 10⁻⁴m/sec, which is 4.5 times that obtained without the borehole device. The relatively low permeability obtained using the conventional test method is attributed to the presence of a fine-grained slime generated during drilling and a reduction of the test area in the test interval due to a gradual collapse of the borehole walls. This study considers how the use of a borehole stability device to prevent borehole collapse can influence the results of hydraulic tests in alluvial formations. It is expected that the results can be used as a basis for improving the reliability and applicability of hydraulic tests performed in alluvial aquifers.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.591-598
• /
• 2000

In the present study, the variation of settlement, pore water pressure and undrained shear strength through model tests were measured. Also, the variation of water content, unit weight and shear strength by the vane shear tests were observed. In this study, appropriate deposit time of construction equipments used in treatment of hydraulic fills is determined from the prediction curve of increased shear strength in dredged fills.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2000.11a
• /
• pp.247-250
• /
• 2000

This study focused on developing a convolution solution for estimating vertical diffusivity of a less permeable hydrogeologic unit in a bedrock aquifer. The diffusivity and corresponding hydraulic conductivity were estimated using the developed convolution equation. An application case was presented in this study.

• Proceedings of the Korean Society of Coastal and Ocean Engineers Conference
• /
• 2003.08a
• /
• pp.87-97
• /
• 2003

외해로부터 내습하는 파랑을 차단하므로서 해안의 세굴, 침식 등을 방지하고 항내의 정온을 유지하고 항만시설물을 보호하기 위하여 축조되는 방파제, 호안 등의 구조물 형식에는 경사제, 직립제, 혼성제 등 여러 가지가 있다 이 중 경사제는 표면을 파력에 충분히 대항할 수 있는 크기의 사석이나 콘크리트 블록을 쌓아 파랑을 경사면에서 쇄파시켜 에너지를 소멸시킴으로서 소파기능을 발휘한다. (중략)