• 한국항행학회논문지
• /
• 제19권5호
• /
• pp.370-378
• /
• 2015

데이터획득/처리장치는 수리온의 2차양산 항공기에 최초 적용하기 위해 개발한 항공기 구성품으로서 엔진, 동력전달, 유압 등 항공기의 주요 계통의 정보를 처리, 타 계통 및 조종사에게 제공한다. 그러나 항공기 생산시험비행 중 해당 구성품과 관련된 여러 결함이 발생하였으며, 장비의 중요성을 고려할 때 긴급하고 확실한 개선이 요구되었다. 본 논문에서는 항공기에서 발생한 결함을 유형별로 분석하고 그 결과를 바탕으로 동작회로와 소프트웨어 전반에 걸쳐 원인분석 및 개선형상을 검증한 결과를 기술하였다. 특히 결함주입기법 기반의 항공기 연동시험을 통해 구성품 장비단위 뿐 아니라 체계단위에서 효과적으로 개선형상을 검증하였으며 이를 통해 수리온 비행안전성 및 품질 신뢰성을 크게 향상시킬 수 있었다.

• 농업과학연구
• /
• 제46권4호
• /
• pp.723-735
• /
• 2019

The power-train is the most important component of an agricultural tractor. In this study, the strength of the driving gear transmission of an 82 kW-class tractor was analyzed using equivalent torque during plow tillage. The load measurement system consisted of an engine revolution speed sensor, torque-meters, revolution speed sensors for four axles, and pressure sensors for two hydraulic pumps. The load data were measured during plow tillage for four speed stages: F2 (2.78 km/h), F5 (5.35 km/h), F7 (7.98 km/h), and F8 (9.75 km/h). Aspects of the gear-strength such as bending stress, contact stress, and safety factors were analyzed under two torque conditions: the equivalent torque at the highest plow load for the F8 speed stage and the maximum engine torque. The simulation results using KISSsoft showed that the maximum engine torque conditions had a lower safety factor than did the highest equivalent torque condition. The bending safety factors were > 1 at all gear stages, indicating that gear breakage did not occur under actual measured operating conditions, nor under the maximum torque conditions. However, the equivalent torque condition in the contact stress safety factor was > 1, and the maximum torque condition was < 1 at the first gear pair. The method of analysis using the equivalent torque showed lower stress and higher safety factor than did the method using maximum torque. Therefore, when designing a tractor by applying actual working torque, equivalent torque method would support more reliable product development.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.83-89
• /
• 2000

In hydraulic control system turbine and gear motor type flowmeters are widely used to measure the flow rate under steady flow conditions. With the recent growth of interest in the measurement of instantaneous values of unsteady flow rate the test of the transient response of these flowmeters are in some significance. however an unsteady flow rate mea-surment and its calibration method with a fast response and a high accuracy have not beendeveloped. In this research particularly the dynamic characteristics of turbine and gear motor type flowmeters are investigated experimentally and simple mathematical models are proposed. The measured flow rate waveforms are compared with those by remote instan-taneous flow rate measurement method(RIFM) which has been developed by author and used for calibration As the result of frequency response test gain and phase between the measured flow rate waveforms by turbine type flowmeter and those estimated by RIFM are in good agreement up to 70Hz For the gear motor type flowmeter th simulated results by a math-ematical model proposed here agree well with the experiment nearly up to 100Hz. Also it if sound that the pressure drop across the flowmeter is increased in proportion to the frequency of the flow rate variation in a high frequency region of more than 100Hz. It can be explained that the dealy of gear motor type flowmeter in high frequency regionis mainly attributed to a first order delay consisting of the inertia of gears and internal leakage of the gear motor.

• Journal of the Korean Wood Science and Technology
• /
• 제43권5호
• /
• pp.682-690
• /
• 2015

The bonding performance of two types of wood adhesives, namely phenol-resorcinol-formaldehyde (PRF) resin and melamine-urea-formaldehyde (MUF) resin for glued laminated timber manufactured by high frequency (HF) heating was evaluated. The HF heating system consists of HF oscillator with dielectric heating system for curing adhesives, and hydraulic press system for clamping glued laminated timber. The designed frequency and output power of the HF system was as 5 MHz and 60 kW, respectively. To verify dielectric heating mechanism under HF oscillation, the heat loss factors of laminae and adhesives were measured. The results show that it is possible to selectively heat adhesives for their curing due to the remarkably higher loss factor of the adhesives than those of wood laminae. The temperature of adhesive in the bonding line reached up to the set temperature within a few seconds by high frequency oscillating, which advanced the curing of adhesive afterwards. The bonding performance, such as shear strength of bonding line, water soaking delamination, and boiling water soaking delamination of PRF resin met the requirement of Korean Standard (KS), however the MUF resin did not meet the KS requirement of boiling water soaking delamination. These results indicate that the HF heating system is successful to manufacture glued laminated timbers with PRF resins to meet the bonding requirements.

• 한국해양공학회지
• /
• 제22권6호
• /
• pp.88-94
• /
• 2008

The concentration of atmospheric carbon dioxide (CO2), which is one of the major greenhouse gases, continues to rise with the increase in fossil fuel consumption. In order to mitigate global warming the amount of CO2 discharge to the atmosphere must be reduced. Carbon dioxide capture and storage (CCS) technology is now regarded as one of the most promising options. To complete the carbon cycle in a CCS system, a huge amount of captured CO2 from major point sources such as power plantsshould be transported for storage into the marine or ground geological structures. Since 2005, we have developed technologies for marine geological storage of CO2,including possible storage site surveys and basic design of CO2 transport and storage process. In this paper, the design parameters which will be useful to construct on-shore and off-shore CO2 transport systems are deduced and analyzed. To carry out this parametric study, we suggested variations in thedesign parameters such as flow rate, diameter, temperature and pressure, based on a hypothetical scenario. We also studied the fluid flow behavior and thermal characteristics in a pipeline transport system.

• 대한토목학회논문집
• /
• 제32권2B호
• /
• pp.139-147
• /
• 2012

본 연구는 자연하천의 모래 179개, 자갈 992개, 조약돌 651개, 호박돌 53개 수로로 구성된 현장실측 1,875개 하천자료를 사용하여 흐름 저항에 대한 Darcy-Weisbach 마찰계수와 Manning의 조도계수 및 무차원 유속의 관계식을 각각 유도하였다. 멱함수 형의 이들 관계식은 유량, 수로경사 및 상대 잠수비에 대한 함수식으로 회귀분석과 반 경험적 방법에 의해 제안하였다. Box-Whisker 분석에 의한 Manning 조도계수의 실측치 분포는 각각 모래자료에서 0.004~0.151, 자갈자료에서 0.008~0.250, 조약돌 자료에서 0.015~0.327 및 호박돌 자료에서 0.023~0.444로 나타났다. 이들 반 경험적 관계식과 저항계수는 수공분야의 정보제공에 유용하게 사용될 것이다.

• 드라이브 ㆍ 컨트롤
• /
• 제14권2호
• /
• pp.23-29
• /
• 2017

In this study, a flexible multi-body dynamic simulation model of a knuckle boom crane is developed to evaluate the stress of spindle and rack gears under dynamic working conditions. It is difficult to predict potential critical damage to a knuckle boom crane if only the static condition is considered during the development process. To solve this issue, a severe working scenario (high speed with heavy load) was simulated as a boundary condition for testing the integrity of the dynamic simulation model. The crane gear model is defined as a flexible body so contact analysis was performed. The functional motion of a knuckle boom crane is generated by applying forces at each end of the rack gear, which was converted from hydraulic pressure measured for the experiment. The bending and contact stress of gears are theoretically calculated to validate the simulation model. In the simulation, the maximum stress of spindle and rack gears are observed when the crane abruptly stops. Peak impact force is produced at the contact interface between pinion and rack gears due to the inertia force of the boom. However, the maximum stress (bending/contact) of spindle and rack are under the yield stress, which is safe from damage. By using the developed simulation model, the experiment process is expected to be minimized.

• 한국항공우주학회지
• /
• 제44권5호
• /
• pp.439-446
• /
• 2016

이 논문에서는 무베어링 로터의 동특성을 비회전 강성 및 진동수 측정 시험과 회전 훨타워 시험을 통해 살펴보았다. 무베어링 로터의 주요 구성품인 블레이드, 유연보, 토크튜브에 대해 강성 및 고유진동수를 측정하여 해석을 위한 물성치를 확보하였고, 훨타워 시험 전에 댐퍼와 스너버를 장착한 무베어링 로터를 조립하여 지상에서 하중이 부가되는 조건하에 기능시험을 수행하여 로터 구성품간의 간섭 여부, 기구학적 거동 등을 확인하였다. 4개의 블레이드를 가지고 회전반경이 5.82m인 무베어링 로터의 회전 동특성시험을 회전면 높이가 9.65m인 훨타워에서 수행하였다. 정지비행성능을 확인하기 위해 추력과 사용동력을 측정하였으며, 회전시 블레이드의 고유진동수 및 감쇠를 측정하기 위해 유압 가진기를 통하여 사이클릭 가진을 하였다.

• Journal of Welding and Joining
• /
• 제28권1호
• /
• pp.66-71
• /
• 2010

With large specific strength and outstanding corrosion resistance and erosion resistance in sea water, titanium and titanium alloy are widely used in heat exchanger production. In particular, pure titanium demonstrates outstanding molding performance and may be considered optimal for production of heat exchanger. Since titanium is very vulnerable to oxidation and embrittlement during welding, processes with less heat input are widely used, and laser welding is widely applied by considering production performance and shield etc in atmosphere. So far, 1st report and 2nd report compared and analyzed embrittlement degrees by bead colors of weldment through oxygen and nitrogen quantitative analysis and hardness measurement, and evaluated welding performance and mechanical properties of butt welding. This study evaluated field applicability of lap welding to heat exchange plate of LPG re-liquefaction device for ships through tensile stress test, hardness test and internal pressure test etc after deducing optimal weding condition and applying to actual heat exchange plate. In bead overlap area, the experiment produced sound welds with no porosity or defect by increasing and decreasing laser power, and tensile-shear test results indicated virtually the same tension and yield strength as base metal. As a result of measuring hardness at lateral cross section and bead overlap zone of actual heat exchanger welds, hardness difference within 20Hv was produced at base metal, HAZ and weldment, and as a result of pneumatic and hydraulic pressure test, no leakage occurred.

• 한국항공우주학회지
• /
• 제34권3호
• /
• pp.81-86
• /
• 2006

본 논문은 유압 공급 면에서는 2중으로 전기제어 면에서는 3중으로 다중화된 DDV 구동장치에 대한 구동전류 고장 모니터 설계에 관한 논문이다. 다중화된 신호들 가운데 어느 한 채널에 고장이 발생한다면, 이 신호는 정확히 감지되어야 하고, 시기적절하게 제거되어야 하며, 남겨진 정상채널들은 그 기능이 재조정되어야 한다. 조종면 구동장치의 고장 모니터 설계는 비행체 역학, 비행제어법칙, 그리고 유압 구동장치 운동특성이 모두 고려된 통합적 관점에서 수행되어야 한다. MIL-F-8785C에서 규정하고 있는 고장에 따른 비행체 천이 응답 요구조건으로부터 조종면 구동장치의 고장이탈 한계를 결정하는 설계 방법이 제시되었다.