• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.197-200
• /
• 2005

This paper presents the design of a broadband hybrid mixer using dual-gate FET topology with a low-pass filter which improves return loss of output to isolate RF and LO signal. The low-pass filter shows the isolation whose RF and LO signal is better than 40 dBc at 2 GHz and 5 GHz band. The dual-gate mixer which has been designed by using cascade topology operates when the lower FET is biased in linear region and the upper FET is in saturation. The input matching circuit has been designed to have conversion gain from 2 GHz to 6 GHz. The designed mixer with low-pass filter shows the conversion gain of better than 7 dB from 2 GHz to 6 GHz at a low LO power level of 0 dBm with the fixed IF frequency of 21.4 MHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권2호
• /
• pp.246-251
• /
• 2014

In this paper, a high-speed CMOS Image Sensor (CIS) based on a 10-bit two step Single Slope A/D Converter (SS-ADC) is proposed. The A/D converter is composed of both 5-bit coarse ADC and a 6-bit fine ADC, and the conversion speed is 10 times faster than that of the single-slope A/D convertor. In order to reduce the pixel noise, further, a Hybrid Correlated Double Sampling (H-CDS) is also discussed. The proposed A/D converter has been fabricated with 0.13um 1-poly 4-metal CIS process, and it has a QVGA ($320{\times}240$) resolution. The fabricated chip size is $5mm{\times}3mm$, and the power consumption is about 35 mW at 3.3 V supply voltage. The measured conversion speed is 10 us, and the frame rate is 220 frames/s.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권10호
• /
• pp.507-513
• /
• 2003

Nowadays, the necessity of linear position control motors have been increased in the various fields of the automatic control system. In the recently, the position control motor have disadvantaged in the efficiency and economical view since it require a conversion equipments such as belt and gear in order to convert rotary to linear motion. On the contrary, the hybrid linear stepping motor(HLSM) of linear motion digital actuator has a direct drive method that do not need mechanical conversion equipments. Therefore, the HLSM is better advantaged in the efficiency and economical view than a rotary stepping motor. In this paper, we have designed an optimum tooth shape and a permanent magnet value between the mover teeth by the 2D finite element method(FEM) to develop the HLSM with longitudinal flux machine(LFM) type, and calculated the thrust force and normal force. And we have manufactured the prototype of it. and have experimented the thrust force and the dynamic thrust characteristics of it.

• 대한전자공학회논문지
• /
• 제24권2호
• /
• pp.190-195
• /
• 1987

This approach to the transmultiplexer is for the 12-channel TDM/FDM translation system with the polyphase network and the FDCT. For the reduction of the conversion time the 14-point FDCT algorithm is used and the polyphase network which translate the protorype filter into the channel filtrs required in each channel is designed. The prototype filters is designed by the IIR/FIR hybrid filter. The number of numerator terms of the hybrid filter is very large compaired to the denomiator terms. Because of symmetrical properties for numerator terms, required multiplication rate is 0.11396x10**6M/sec.ch. and reduced to 25%-45% of the rate required in the other papers. The proposed system is simulated with the computer and by the results it is proved that the proposed conversion method is valid.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 추계학술대회 논문집
• /
• pp.13-14
• /
• 2016

This paper has introduces a novel Integrated On-board Charger (IOBC) to reduce the size, weight and cost of power conversion stages in Electric Vehicles (EVs). The IOBC is composed of an OBC and a low voltage dc-dc converter (LDC). The IOBC includes a bidirectional ac-dc converter and a bidirectional full-bridge converter with an active clamp circuit. The LDC converter is a hybrid topology combining an active clamped full-bridge converter and a forward converter derived from the Weinburg converter topology. Unlike conventional OBC, the proposed IOBC is compact and the LDC converter of it can achieve a higher efficiency. In addition, the LDC converter of the proposed IOBC can achieve high step-down voltage conversion ratio, no circulating current, no reverse recovery current of the rectifier diodes and small ripple current of output inductor on the auxiliary battery. A 1kW hardware of the LDC converter is implemented to verify the performances of the proposed IOBC.

• 한국수소및신에너지학회논문집
• /
• 제15권4호
• /
• pp.283-290
• /
• 2004

The single-step process for conversion of syngas to DME give higher conversion than the syngas-to-methanol process. This arises because of a synergy among the three simultaneous reaction, methanol synthesis, methanol dehydration and water gas shift reaction, in the process. we would find the optimal condition of the process which these advantages. The optimal condition of DME synthesis reaction over a commercial $Cu/Zn/Al_2O_3$ catalyst and Hybrid catalyst in a fixed bed reactor. The syngas-to-dimethyl ether conversion was examined on various reaction condition (Temperature 473~553K, $H_2/CO$ ratio 1~3, Pressure 30'50atm, GHSV 1000~4000).

• 설비공학논문집
• /
• 제28권2호
• /
• pp.75-80
• /
• 2016

There are three types of dehumidification systems : refrigeration dehumidification method, desiccant dehumidification method and hybrid dehumidification method. The first method involves removing moisture by condensation below the dew point, the second method involves absorption by a desiccant material and the last is an integration method. However, the refrigeration dehumidification system consumes too much power and controlling the humidity ratio is difficult. The desiccant dehumidification system uses less power but it has problems of environmental pollution. The hybrid dehumidification system has the disadvantage of a high initial cost. On the other hand, the energy consumption of the membrane based dehumidification system is lower than for the refrigeration dehumidification system. Also, it is an environmentally friendly technology. In this study, the performance parameters are evaluated for the dehumidification system using a hollow fiber membrane. Available area, duct side dry-bulb temperature, sweep gas flux (flow rate) and LMPD (Log Mean Pressure Difference) were used as the performance parameters.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.35-38
• /
• 2002

In this paper, for digital x-ray conversion receptor development studied by hybrid technology of based on CdZnTe. For this study, First searched fabricate method of CdZnTe x-ray receptor. Second, search the phosphor material & fabricate method for scintillator layer. Fabricated sample is analyzed with physical & electric measurement. This result is showed good SNR ratio hybrid thechnology with direct method & indirect method. In this paper offer the method can reduce the dark-current in the hybrid X-ray detector.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1181-1184
• /
• 2008

$GeO_2$/ormosil organic-inorganic hybrid films doped with neodymium ions and $TiO_2$/Ormosil organic-inorganic hybrid films dispersed with neodymium oxide nanocrystals are prepared by combining an inverse microemulsion technique and a low-temperature sol-gel technique. The effects of $Nd^{3+}$ concentration, $Nd_2O_3$ nanocrystal content, and heat treatment temperature on up-conversion and photoluminescence luminescence properties of the hybrid films are studied.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제11권12호
• /
• pp.5981-5997
• /
• 2017

Advanced Television Systems Committee (ATSC) produced ATSC 2.0 standard, which has been used for a HD/SD digital broadcasting service with MPEG-2 Transport Stream (TS) as a delivery protocol. Recently, users might want to consume multimedia services without being constrained by transport network. However, MPEG-2 TS is not suitable protocol for IP network. Thus, ATSC has enacted ATSC 3.0 standard, which is designed for a hybrid service through a conversion of both broadcasting and broadband channels. The ATSC 3.0 specifies delivery protocols as MPEG Media Transport (MMT) for a broadcasting environment and Dynamic Adaptive Streaming over HTTP (DASH) for a broadband. However, it seems difficult to combine broadcast and broadband for hybrid broadcasting, and it is difficult to synchronize media data between MMT and DASH. This paper suggests various new service scenarios to be brought up by a hybrid broadcasting, ATSC 3.0, and also proposes a stable mechanism for switching contents between different delivery protocols such as MMT and DASH.