• Journal of Power Electronics
• /
• 제10권3호
• /
• pp.277-284
• /
• 2010

This paper presents a novel hybrid carrier based space vector modulation for cascaded multilevel inverters. The proposed technique inherits the properties of carrier based space vector modulation and the fundamental frequency modulation strategy. The main characteristic of this modulation are the reduction of power loss, and improved harmonic performance. The carrier based space vector modulation algorithm is implemented with a TMS320F2407 digital signal processor. A Xilinx Complex Programmable Logic Device is used to develop the hybrid PWM control algorithm and it is integrated with a digital signal processor for hybrid carrier based space vector PWM generation. The inverter offers less weighted total harmonic distortion and it operates with equal electrostatic and electromagnetic stress among the power devices. The feasibility of the proposed technique is verified by spectral analysis, simulation, and experimental results.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.441-441
• /
• 2014

The characteristics of hybrid conductive films based on multilayer graphene and silver grid have been investigated for the high-performance and flexible organic solar cells. The hybrid conductive films have been prepared on glass and polyethylene terephthalate (PET) substrates using conventional photolithography process and transfer process of graphene. The optical and electrical properties of prepared conductive films show transmittance of 87% at 550nm and sheet resistance of $28{\Omega}/square$. The electromechanical properties were also investigated in detail to confirm the flexibility of the hybrid films. OSCs have been fabricated on the hybrid conductive films based on graphene and silver grid on glass substrate. The power conversion efficiency of 2.38%, a fill factor of 51%, an open circuit voltage of 0.58V and a short circuit current of $8.05mA/cm^2$ were obtained from the device on glass substrate. The PCE was enhanced 11% compared with OSCs on the MLG films without silver grid.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.190.2-190.2
• /
• 2014

We report the origin of the improvement of the power conversion efficiency (PCE) of hybrid thin-film solar cells when a soluble C60 derivative, [6,6]-phenyl-$C_{61}$-butyric acid methyl ester (PCBM), is introduced as a hole-blocking layer. The PCBM layer could establish better interfacial contact by decreasing the reverse ark-saturation current density, resulting in a decrease in the probability of carrier recombination. The power conversion efficiency of this optimized device reached a maximum value of 8.34% and is the highest yet reported for hybrid thin-film solar cells.

• 한국해양공학회지
• /
• 제14권2호
• /
• pp.1-6
• /
• 2000

Wave energy absorption by a flap equipped with a harbor in a water of finite depth is studied. The wave potential is calculated by a hybrid integral equation consisting of Green integral equations associated with Rankine and Kelvin Green functions. The absorbed wave energy is calculated by both the near-field and far-field methods. The present methods can be used for the design of a flap-harbor wave energy absorber since the numerical results by the two methods are in good agreement.

• 한국태양에너지학회 논문집
• /
• 제34권3호
• /
• pp.30-41
• /
• 2014

PV/Thennal combined system is a solar energy device that uses photovoltaic module as thermal absorption plate, producing thermal energy as well as electricity which can be utilized in buildings. The system removes heat from PV module through air or liquid and its efficiency will vary dependant on the thermal medium. The heat as the forms of hot air or hot water can be utilized for building use, like space heating and hot water. A significant amount of research and development on hybrid PV/thermal(PVT) collectors has been carried out. This study reviews literature on the research of air-based hybrid PVT collectors in terms of their design and energy performance.

• 한국컴퓨터산업학회논문지
• /
• 제6권2호
• /
• pp.345-354
• /
• 2005

그리드 사용자에게 시간과 장소에 상관없이 그리드 서비스를 이용할 수 있게 해주는 기술이 모바일 그리드이다. 이동환경에서 그리드 서비스를 제공하기 위해서는 단말기 배터리의 성능 및 이동성의 고려 등 여러 가지 제약사항이 따르며, 유선망에서의 그리드 기술을 이동 환경에 적용하기에는 많은 어려움이 있다. 따라서 본 논문에서는 모바일 그리드 서비스를 제공하기 위한 모바일 그리드 구조를 Ad-hoc 네트워크를 이용하여 설계를 하였으며, NS-2(Network Simulator)를 이용한 시뮬레이션을 통한 세 가지 방법의 라우팅 프로토콜의 지연시간에 대한 측정 및 이동 단말기 배터리의 성능을 고려한 비교를 통해, hybrid 방식의 라우팅 프로토콜이 효율적임을 제시하였다. 향후 모바일 그리드 서비스를 제공하기 위한 자원 할당 및 신뢰성 확보 방안에 대한 연구를 수행할 예정이다.

• 한국표면공학회지
• /
• 제43권6호
• /
• pp.272-277
• /
• 2010

We investigated the life time characteristics of OLED device with aluminium oxide ($AlO_x$) passivation film on glass substrate and polyethylene terephthalate (PET) substrate by RF magnetron sputtering for the transparent barrier film applied to flexible OLED device. Basic buffer layer was determined as $Alq_3$(500 nm)-LiF(300 nm)-Al(1200 nm), and the most suitable aluminium oxide ($AlO_x$) film have been formed when the partial volume ratio of oxygen was 20% and the sputtering power was 100 watt and the minimum thickness of buffer was $2\;{\mu}m$. $AlO_x$/epoxy hybrid film was also used as a effective passivation layer for the purpose of improving life time characteristics of OLED devices with the glass substrate and the plastic substrate. Besides, the simultaneous deposition of $AlO_x$/epoxy film on back side of PET could result in better improvement of life time.

• Smart Structures and Systems
• /
• 제6권1호
• /
• pp.1-16
• /
• 2010

This paper presents a novel smart MEMS accelerometer which employs a hybrid control algorithm and an estimator. This scheme is realized by adding a sliding-mode controller to a conventional PID closed loop system to achieve higher stability and higher dynamic range and to prevent pull-in phenomena by preventing finger displacement from passing a maximum preset value as well as adding an adaptive nonlinear observer to a conventional PID closed loop system. This estimator is used for online estimation of the parameter variations for MEMS accelerometers and gives the capability of self testing to the system. The analysis of convergence and resolution show that while the proposed control scheme satisfies these criteria it also keeps resolution performance better than what is normally obtained in conventional PID controllers. The performance of the proposed hybrid controller investigated here is validated by computer simulation.

• 제어로봇시스템학회논문지
• /
• 제11권7호
• /
• pp.602-608
• /
• 2005

In the virtual environment, force feedback to the human operator makes virtual experiences more realistic. To ensure the safe operation and enhance the haptic feeling, stability should be guaranteed. Both motors and brakes are commonly used for haptic devices. Motors can generate a torque in any direction, but they can make the system active during operation, thus leading to instability. Brakes can generate a torque only against their rotation, but they dissipate energy during operation, which makes the system intrinsically stable. Consequently, motors and brakes are complementing each other. In this research, a two degree-of-freedom (DOF) haptic device equipped with motors and brakes has been developed to provide better haptic effects. Each DOF is actuated by a pair of motor and brake. Modeling of the environment and the control method are needed to utilize both actuators. Among various haptic effects, contact with the virtual wall, representation of friction and representation of plastic deformation have been investigated extensively in this paper. It is shown that the hybrid haptic device is more suited to some applications than the motor-based haptic device.

• 한국전기전자재료학회논문지
• /
• 제35권3호
• /
• pp.269-274
• /
• 2022

We prepared carbon nanotube (CNT) paper by a vacuum filtration method for the use of a chip-typed resistor as a precision passive device with a constant resistance. Hybrid resistor composed of the CNT resistor with a negative temperature coefficient of resistance (T.C.R) and a metal alloy resistor with a positive T.C.R could lead to a constant resistance, because the resistance increase owing to the temperature increase at the metal alloy and decrease at the CNT could counterbalance each other. The constant resistance for the precision passive devices should be maintained even when a heat was generated by a current flow resulting in resistance change. Performance reliabilities of the CNT resistor for the precision passive device applications such as electrical load limit, environmental load limit, and life limit specified in IEC 60115-1 must be ensured. In this study, therefore, the rated power determination and T.C.R tests of the CNT paper were conducted. -900~-700 ppm/℃ of TCR, 0.1~0.2 A of the carrying current capacity, and 0.0625~0.125 W of the rated power limit were obtained from the CNT paper. Consequently, we confirmed that the application of CNT materials for the precision hybrid passive devices with a metal alloy could result in a better performance reliability with a zero tolerance.