• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.651-654
• /
• 2000

A fermentation study of the recombinant Escherichia coli system has been tired to overproduce a recombinant Paragonimus westermani cysteine proteinase, rPwCP1. Using the modified LB media, main cultures and chemical induction with IPTG were carried out to examine the possibility of secretory protein overproduction at high cell density culture. As a result, the target protein of rPwCP1, purified by metal affinity chromatography and gel filtration, has been shown at 50.8 kDa on SDS-PAGE, and its final concentration turns out to be 350mg/L.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.206-211
• /
• 2008

Noise sources in electric machines are broadly categorized as magnetic, mechanical, electronic and aerodynamic. Especially, there are several kinds of noise sources due to the change of reluctance by rotor position in IPM motor. To separate acoustic noise by mechanical structure and electromagnetic sources, resonance frequency and the effect of vibration and acoustic noise by electromagnetic sources are analyzed. And then, the structural and electromagnetic designs to reduce acoustic noise are performed. The relevance about the study on noise reduction of IPM motor is verified by noise experiment, noise and vibration analysis.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.812-814
• /
• 1999

In this paper, we are applied the Genetic Algorithm (GA) to design of fuzzy logic controller (FLC) for a DC Servo-Motor Speed Control. GA is used to design of the membership functions and scaling factor of FLC. To evaluate the performances of the proposed FLC, we make an experiment on FLC for the speed control of an actual DC servo-motor system with nonlinear characteristics. Experimental results show that proposed controller have better performance than those of PD controller.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.56-58
• /
• 1993

This report describes the high speed DC motor (8,000 rpm) that we have designed, manufactured and tested. DC motor is the best drive system in electric-mechanical energy conversion. The design concept for high speed and high energy density to DC motor is to maximize Ampere-conductor in armature and to maximize flux density in armature teeth, armature core, pole, yoke using flux path.

• Proceedings of the Korean Society of Toxicology Conference
• /
• 2003.05a
• /
• pp.48-49
• /
• 2003

Toxicogenomics is a term that represents the merging of toxicology with novel genomics techniques. Microarray, which provides a revolutionary basis to perform global gene expression analyses and to decode biological pathways, has begun to have a major impact on many different fields of drug discovery and development. (omitted)

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1712-1713
• /
• 2008

In this paper, we develop the vision control systems of auto tracking based on image processing techniques for video conference. The developed auto tracking vision control system consists of control hardware including vision, two dc motors and dc motor drivers. Image processing techniques are used to pixel of two images. Motion detection algorithm is applied to eliminate the noise. Experiment results are presented to illustrate the effectiveness and the applicability of the approaches proposed.

• Imaging Science in Dentistry
• /
• v.34 no.4
• /
• pp.219-223
• /
• 2004

Metastases to the jawbones are found predominantly in the mandible and are rare in relation to the overall spectrum of oral malignancy. Analysis of the literature shows that the most frequent primary sites are the breast, lung, kidney, thyroid, and prostate. Adenocarcinoma of the mandible, whether primary or metastatic, are usually difficult to diagnose clinically. We report a case illustrating the clinical, radiographic, and histologic findings of a metastatic lung adenocarcinoma of the anterior mandible in a 58-year-old male.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1384-1387
• /
• 2003

Pressurization test is usually required in aircraft full-scale static test. There are several test conditions including pressurization of cockpit, fuselage fuel tank, air inlet duct for T-50 full-scale static test. In this paper, the test conditions, equipment, piping analysis for the pressurization test are introduced. Tank simulation test is performed to verify the validity of piping analysis and to find good tuning parameters for the pressurization channel in the servo controller. Several test setup for pressurization of T-50 test is introduced. Test article volume is filled by form, $60%{\sim}80%$ volume is reduced for the T-50 full-scale static test. Pressurization system is connected to servo controller which also controls hydraulic actuator. Load and pressure control is synchronized by using the same servo controller during T-50 test. Typical control result for pressurization test condition is shown. Pressurization tests of T-50 full-scale static test was completed successfully.

• Korean Journal of Medicinal Crop Science
• /
• v.11 no.4
• /
• pp.316-320
• /
• 2003

A protocol is described for rapid multiplication of Zanthoxylum piperitum DC. (Rutaceae), an important aromatic and medicinal plant, through shoot-tip explant cultures. Murashige and Skoog (MS) medium supplemented with various concentrations of N-6-benzyladenine (BA), N-6-benzylaminopurine (BAP) and thidiazuron (TDZ), in single or in combination with ${\alpha}-naphthaleneacetic$ acid (NAA), was used to determine the rate of shoot proliferation. N-6-benzyladenine (BA) used at 0.5mg/l, was the most effective in initiating multiple shoot proliferation at the rate of 23 microshoots per shoot-tip explants after 40 days of culture. Shoot multiplication increased 1.2-fold in each successive subculture. Induction of rooting (98%) was achieved by transferring the shoots to the same basal medium containing 2 mg/l indole-3-butyric acid (IBA). Plantlets went through a hardening phase in a controlled growth chamber, prior to in vivo transfer. These results represented that possible application for the mass production of plantlets through in vitro culture system of Zanthoxylum piperitum DC.

• KIEAE Journal
• /
• v.7 no.3
• /
• pp.57-62
• /
• 2007

Most of current building materials are made of organic compounds or at least made with chemical treatments. Though easy to use and comparatively pay less, those materials are generally not enviornmentally sound. VOC is one of harmful effects. On contrary, natural materials such as soil are usually eco-friendly, and environmentally sustainable as well if not treated in autoclaves. Acoustica materials made of such environmentally sound and sustainable could be widely used. It is aimed to prove that soil based materials could be effectively used in acoustical fields rather than the other usual materials. Experiments with various types of soil blocks and soil plaster were performed. It is proved that the soil plaster has better apsorption features than cement plaster. Soil blocks have higher absorption cofficients than soil plaster, due to the thickness, and the absorption characteristics can be controlled by the design of the blocks.