• 대한조선학회논문집
• /
• 제41권3호
• /
• pp.60-71
• /
• 2004

Nowadays, We have had a growing interest in high-speed vessels' because it is very important to save time and cost in marine transportation. The development of hull form for high-speed vessels is high priority to secure the competitive power for the transportation of cargos. Therefore, the demand of the high-speed vessels is gradually increased, but the conventional hull forms are limited by rapidly increasing resistance upon the increase of ship speed in high-speed region. Therefore, new concepts for the hull form of high-speed vessels have been requested. One of the derived hull forms for that demand is the hull form of trimaran type. Trimaran has a very slender main hull as compared with conventional single hull so that is reduced in wave resistance. The slender main hull has the undesirable characteristics of stability, but two side hulls make up for the week points in the stability. That is, trimaran is able to have desirable performances for the resistance and stability. In this paper, for the design of 200TEU class container vessel with trimaran type, which will be cruised in Yellow-Sea region, firstly a preliminary hull is designed, and the model test is carried out with the variation of side hull position. From the experience of the preliminary hull form design, an improved hull form for the 200TEU container are designed, and the model tests are carried out. Also, a numerical computation technique is adopted for the simulation of flow phenomena around the designed hull forms. The final hull form is compared with existing ships for the resistance performance from the computation with computer and ship model tests.

• 수산해양기술연구
• /
• 제44권1호
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 춘계학술대회 논문집
• /
• pp.266-269
• /
• 2001

This paper describes the effect of hull form on motion characteristics of FPSO. The purpose of the present study is to investigate seakeeping performance of ship type FPSO in comparison with those of barge type FPSO. Model test result shows that the barge type FPSO is better in heave and pitch motion, while the ship type FPSO is superior in roll motion.

• Journal of Ship and Ocean Technology
• /
• 제5권4호
• /
• pp.19-28
• /
• 2001

A comparative study of the new flexible double hull structure is presented as a collision energy absorbing system, which is constructed with mixed stringers comprising slant and straight stringers for the double hull tanker, The dimension and disposition of this mixed stringers are selected to give the maximum absorbing energy. From the viewpoint of collision energy absorbing efficiency, this structural system is compared with three other types of the double hull constructions with trapezoidal stiffener, stringer type and standard type of VLCC, 310K DWT, Based on the constant hull weight, the proposed double hull structure with mixed stringers shows a improved crashworthiness as the results.

• 대한조선학회논문집
• /
• 제46권4호
• /
• pp.398-408
• /
• 2009

Crude oil carriers or product oil carriers are confronted with sea pollution due to hull damage from various accidents. To reduce the oil spillage of tankers, IMO(International Maritime Organization) and OPA 90(Oil Pollution Act 1990) adopted the hull structures of double skin type. In this study, oil spillage test of the double skin tanker with 1/100 scaled model was carried out under damaged condition due to collision and grounding accidents. A new structural type of oil tanker was also tested with pipe and valve system arranged in double side and single bottom hulls. Their results were compared with that of conventional type double hull on the view point of ship safety and oil spillage.

• 대한조선학회논문집
• /
• 제52권5호
• /
• pp.365-371
• /
• 2015

Hull plate consists of various types of curved plates and there also exists corresponding processing methods. Typically, curved plates can be divided into convex type and saddle type. Large amount of research has been conducted mainly focusing on application of processing method of convex type, saddle type and hybrid type, but research on determination and processing method application of the most difficult S-shaped curved plate that has inflection lines has not been carried out yet. In this paper, as the fundamental research of appropriate processing method application, a calculation method is proposed to calculate inflection lines on curved plates. In order to calculate inflection lines, normal curvature and information of fabricated curved plates should be utilized. We compare the workability of the fabrication for hull plate using inflection line.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2001년도 춘계학술대회 논문집
• /
• pp.53-59
• /
• 2001

In this Paper, the resistance performances of twin hull forms, which are simplified as two-dimensional wedge shape, are experimentally investigated in low and middle speed ranges to find out the effect of distance between two hulls and fore-body shape for the future hull form development of catamaran type sweeping vessel. The model tests are performed for seven different cases for three models in the circulating water channel(CWC) of Inha Technical College. The free surface flows are observed together to investigate the relation between resistance performance and free surface characteristics. A conceptual design for the modification of bow hull form is presented and the efficiency is discussed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권1호
• /
• pp.100-114
• /
• 2015

This paper deploys optimization techniques to obtain the optimum hull form of KSUEZMAX at the conditions of full-load draft and design speed. The processes have been carried out using a RaPID-HOP program. The bow and the stern hull-forms are optimized separately without altering neither, and the resulting versions of the two are then combined. Objective functions are the minimum values of wave-making and viscous pressure resistance coefficients for the bow and stern. Parametric modification functions for the bow hull-form variation are SAC shape, section shape (U-V type, DLWL type), bulb shape (bulb height and size); and those for the stern are SAC and section shape (U-V type, DLWL type). WAVIS version 1.3 code is used for the potential and the viscous-flow solver. Prior to the optimization, a parametric study has been conducted to observe the effects of design parameters on the objective functions. SQP has been applied for the optimization algorithm. The model tests have been conducted at a towing tank to evaluate the resistance performance of the optimized hull-form. It has been noted that the optimized hull-form brings 2.4% and 6.8% reduction in total and residual resistance coefficients compared to those of the original hull-form. The propulsive efficiency increases by 2.0% and the delivered power is reduced 3.7%, whereas the propeller rotating speed increases slightly by 0.41 rpm.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권4호
• /
• pp.1-10
• /
• 1993

This paper introduces the outline of hull structure to the sorts of LNG carrier briefly. Especially, explains in detail for the insulation system of Moss Rosenberg Verft spherical tank type LNG carrier. It is not easy task to calculate exactly the temperature distribution of hull because of very complicated structure of hull. Therefore, in this paper by the adequate modeling of the Moss Rosengerg spherical tank type LNG carrier, a program is developed which calculate the temperature distribution of every hull and estimate the heat influx from every hull and output the BOR according to the variation of atmospheric conditions on boyage.

• 한국해양공학회지
• /
• 제30권2호
• /
• pp.69-74
• /
• 2016

A new wave-piercing-type high-speed planing boat without a chine was developed, and its basic performance was investigated in a model test, including the resistance, trim, and sinkage. The maximum speed of the developed ship was 35 knots. The hull form was developed by combining a VSV (very slender vessel) and TH (transonic hull), which have large deadrise angles at the bow. The main dimensions were estimated by a statistical approach using actual ship data. The effect of a side fin attached at the stern near the water line was investigated from a resistance point of view. It was found that the developed hull form showed the possibility of a new concept for a high-speed planing hull without a chine, and the side fin played an important role in increasing the resistance performance by controlling the trim and sinkage in the high-speed range.