• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.5
• /
• pp.499-508
• /
• 2017

This paper uses optimization techniques to obtain bow hull form of a 66,000 DWT bulk carrier in calm water and in waves. Parametric modification functions of SAC and section shape of DLWL are used for hull form variation. Multi-objective functions are applied to minimize the wave-making resistance in calm water and added resistance in regular head wave of ${\lambda}/L=0.5$. WAVIS version 1.3 is used to obtain wave-making resistance. The modified Fujii and Takahashi's formula is applied to obtain the added resistance in short wave. The PSO algorithm is employed for the optimization technique. The resistance and motion characteristics in calm water and regular and irregular head waves of the three hull forms are compared. It has been shown that the optimal brings 13.2% reduction in the wave-making resistance and 13.8% reduction in the added resistance at ${\lambda}/L=0.5$; and the mean added resistance reduces by 9.5% at sea state 5.

• Journal of the Korea Society for Simulation
• /
• v.27 no.2
• /
• pp.83-90
• /
• 2018

This paper describes the method of hull shape optimization to improve the resistance performance of planing hulls when a reference hull shape and its principal dimensions are given. First, the planing hull of precedent research is adopted as the reference hull and an optimization problem is formulated by defining hull shape parameters. The search space of this research is discretized for computing cost and DPSO(Discrete binary version of Particle Swarm Optimization) method is used to solve the optimization problem. As the result of optimization, the decrease of resistance is confirmed from the comparison between the reference hull's and the modified hull's planing performance from computational results.

• Journal of Navigation and Port Research
• /
• v.29 no.7
• /
• pp.603-609
• /
• 2005

This paper presents the method for developing an optimum hull form with minimum wave resistance using SQP( sequential quadratic programming) as an optimization technique. The wave resistance is evaluated by a Rankine source panel method with non-linear free surface conditions and the ITTC 1957 friction line is used to predict the frictional resistance coefficient. The geometry of the hull surface is represented and modified using NURBS(Non-Uniform Rational B-Spline) surface patches. To verify the validity of the developed program the numerical calculations for Wigley hull and Series 60 Cb=0.6 hull are performed and the results obtained after the numerical calculations are compared with the initial hulls.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.3
• /
• pp.32-39
• /
• 2004

A design procedure for a ship with minimum total resistance has been developed using a numerical optimization method called SQP(sequential quadratic programming) to search for different optimal hull forms. The frictional resistance has been estimated using the ITTC 1957 model-ship correlation line formula, and the wave resistance has been evaluated using a potential-flow panel method that is based on Rankine sources with nonlinear free surface boundary conditions. The geometry of a hull surface has been modified using B-spline surface patches, during the whole optimization process. The numerical analyses have been carried out for the modified Wilgey hull at three different speeds (Fn=0.25, 0.316, 0.408), and the calculation results were compared.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.5
• /
• pp.785-794
• /
• 2015

To obtain low resistance and high efficiency energy-saving ship, minimum total resistance hull form design method is studied based on potential flow theory of wave-making resistance and considering the effects of tail viscous separation. With the sum of wave resistance and viscous resistance as objective functions and the parameters of B-Spline function as design variables, mathematical models are built using Nonlinear Programming Method (NLP) ensuring the basic limit of displacement and considering rear viscous separation. We develop ship lines optimization procedures with intellectual property rights. Series60 is used as parent ship in optimization design to obtain improved ship (Series60-1) theoretically. Then drag tests for the improved ship (Series60-1) is made to get the actual minimum total resistance hull form.

• Journal of Navigation and Port Research
• /
• v.32 no.8
• /
• pp.583-588
• /
• 2008

The planing craft is designed specifically to achieve comparatively high speed on the surface of the water. In general, the stepped hull craft has effect improvement in speed and fuel-efficiency because of the reduction of total resistance by a small wetted surface area without corresponding stepped hull craft. In this paper, the high speed stepped hull crafts with respect to the number of bottom steps were performed to compare the effect of resistance performance using at-sea model-test method. In conclusion, the stepped hull craft with twin-step was proved to be effective to reduce the total resistance.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.6
• /
• pp.456-464
• /
• 2016

To design the modified hull form with relatively unfavorable dimensions and constraints than the parent ship the stepwise design was applied. In each design step the resistance characteristics was estimated by numerical calculations using CFD programs as Wavis 1.4, Wavis 2.1 and Fluent 12.1. The wave profiles along hull surface by potential flow calculations were investigated to improve wave resistance by modifying the bow shapes. To improve the stern shapes with a point of viscous form resistance the pressure distributions on hull surface and the limiting streamlines are investigated by viscous flow calculations. The design objectives such as shortening the LBP, enlarging the propeller tip clearance, moving forward of the LCB location and increasing the displacement were applied by stepwise to develop the new hull form of DWT 75,000 product oil carrier. Finally a new hull form was developed without the resistance performance loss compared with the parent ship.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.9 no.2
• /
• pp.92-97
• /
• 2006

Hull forms of a high speed small boat have been developed through numerical studies. A round bilge type hull form has been drived form a using chine hull form with HCAD, a hull form variation software. Wave resistance and the flow fields around the ships have been computed using well-known software, WAVIS. This software employs Rankine source method with non-linear tree surface condition as well as dry transom boundary conditions. The round bilge hull form showed better resistance performance than to the chine hull form for the whole speed range. However, considering the building and labor costs of the small shipyard, the chine hull form has been selected and its wave resistance characteristics has been improved by modifying the bow regions and applying the stem wedge. It is found that the effect of stem wedge is quite satisfactory to improve the resistance characteristics of high speed chine hull form.

• Journal of the Korea Safety Management & Science
• /
• v.19 no.4
• /
• pp.301-307
• /
• 2017

The planing hull is characterized by a large change in the posture according to the speed, and the shape of the propeller varies, so that the hull resistance varies greatly depending on the propeller used. Especially, the Savitsky system, which is widely used for estimating the resistance of planing hull, does not consider the characteristics of these propeller and ship bottom spray rails. In this paper, in order to investigate the difference in resistance characteristics between the propeller and the bottom of the propeller of 6m and 12m class propeller using propeller such as outboard or stern drive, A comparative test was conducted on resistance and attitude posture changes in the Circulating Water Channel of Institute of Medium & Small Shipbuilding. As a result of comparison test, it was confirmed that there is a clear difference in the attitude change due to the presence of the bottom floor spray rail and the change in resistance characteristics due to the installation of the propeller. However, attitude change with the propeller was found to be insignificant.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.5
• /
• pp.57-63
• /
• 2004

Various propulsion systems, applicable for a G/T 47,000 class mid-size cruise ship, are discussed and a comparative study on stern forms and hull resistance characteristics is carried out, in relation to these propulsion systems. Based on shipyard production logs on similar cruise ships, a reference hull form of a single shaft propulsion system with center-skeg, is generated. Then two new stern hull forms are derived by using a hull transform technique: consisting of one stern form using a twin-skeg system and the other using the Azipod system. Using a CFD-based commercial flaw analysis program, WAVIS (WAve and VIScous flaw analysis system for hull form development), various hydrodynamic characteristics, including wave profiles and ship hull resistance, are compared for three hull forms.