• 대한조선학회논문집
• /
• 제49권6호
• /
• pp.491-497
• /
• 2012

A hull-form for a 32,000G/T class Ro-Pax ferry has developed in accordance with a need of ferry operators to reduce fuel oil consumption(FOC) due to the drastic increase in oil prices recently and strengthening of environmental rules and regulations such as CO2 emission. A twin-skeg type is applied as the hull-form in lieu of an open-shaft type in order to improve propulsion performance. In order to achieve this object, flow control devices are installed to reduce a propeller induced vibration which is a main reason to obstruct the application of twin-skeg type passenger vessels owing to an uncomfortable vibration level. Numerical simulation by using an in-house code and a commercial code (Fluent) has performed to find out an optimum design of the flow control devices and to check an improvement in cavity volume. Model tests in Samsung Ship Model Basin are carried out to evaluate propulsion performance with the developed twin-skeg type hull and a reference hull of open-shaft type. In conclusion, it is shown that the twin-skeg type hull is better than the open-shaft in FOC by around 7% and in cavity volume by 20% as well.

• Journal of Ship and Ocean Technology
• /
• 제1권1호
• /
• pp.15-25
• /
• 1997

A series of towing tank tests were carried out for 18 full ship models of high block coefficients. The resistance coefficients and wake distribution at the propeller plane were measured and carefully examined. Regression analysis was employed to find out the relationships with the hull form parameters. Equations for wave resistance coefficient, form factor, and nominal wake are given. A harmonic analysis of measured wake was performed to look into the influence of the local stern shape on the magnitude of fluctuating wake components at three different radii. The amplitude of wake harmonics was also expressed by regression quations. It was found that the regression formulas were very useful in estimating resistance and circumferential wake characteristics of full ship models. It was also considered that the formulas presented in this paper could be utilized in the hull form improvement in a preliminary design.

• 대한조선학회지
• /
• 제6권1호
• /
• pp.25-34
• /
• 1969

From viewpoints of over-all ship economy the straight framed V-bottom hull forms with chines are considered to be attractive even for usual commercial vessels, because increments of resistance over that of round hull forms, if any, can be well compensated with reduction in construction cost.[1] To investigate the influences of both prismatic coefficient and chine elevation on resistance performance, three models of straight-framed V-bottom hull forms which are similar to Prof. C. Ridgely-Nevitt's W-18, W-8, and W-20[2],[3] in size and hull form coefficients were tested at the SNU Ship Model Towing Tank for resistance measurements. They are of Cp=0.60, 0.65 and 0.70 and of ${\Delta}/(0.01L)^3=300$. Influence of variation of chine elevation on resistance performance were observed with the test results obtained at normal condition, and at the trimed by the stern by 2% and 4% of $L_{bp}$ at normal condition under same displacement. The hull form characteristics are shown in Table 1, and in Fig. 1, 2, 3, 4 and 5. The test results are shown in Fig 8, 9 and 10 in the form of Cr vs. $V/\sqrt{L}$ curves taking Cp as a parameter for normal condition, trim by the stern in 2% and 4% $L_{bp}$ at normal condition , respectively. Cr vs. $V/\sqrt{L}$ curves taking trim condition as a parameter are also shown in Fig 11, 12 and 13 for Cp=0.60 and 0.70, respectively. The best and the worst trim condition at given $V/\sqrt{L}$ in viewpoint of Cr are plotted for each Cp-value as shown in Fig 14, 15 and 16. From the above results the following conclusions are derived: (1) In general, the resistance performance of the straight-framed V-bottom hull forms are not inferior to those of round hull forms. At a certain range of $V/\sqrt{L}$ the former gives less resistance than the latter. (2) Regarding influences of Cp on Cr, it is observed that, at $V/\sqrt{L}$ less than about 0.925, the greater Cp-value gives the more increment of Cr, and that, at $V/\sqrt{L}$ greater than about 0.925 the smaller Cp-value gives the more increment of Cr. It is also noteworthy that the model of Cp=0.70 has remarkable hump on Cr vs. $V/\sqrt{L}$ curve between $V/\sqrt{L}=0.80$ and 0.90. (3) For higher speed within the test range, the chine elevation having the steeper slope around bow and the easier slope around amidship and stern, refered to watering, give the better results in resistance performance. (4) Assuming the chine elevations adopted for the tested models were not of the best, we would expect further improvement of resistance performance for such form. Hence, a systematic study on chine elevation is very disirable to prepare design data of general purpose for the such hull forms.

• 한국항해항만학회지
• /
• 제32권8호
• /
• pp.583-588
• /
• 2008

활주형선은 고속 운항시 선저에 동적압력을 발생시켜 선체를 부상시킴으로서 저항이 감소하게 되어 고속의 항주가 가능하게 된다. 일반적으로 선저에 스텝을 적용한 선형은 일체형 활주형선에 비하여 고속 주행시 선저 공기공급에 따른 접수면 감소로 인하여 전체저항 감소에 따른 속도향상과 연비절감 효과가 있다. 본 논문에서는 고속 선형시험이 가능한 실 해역모형시험을 이용하여 선저 스텝개수에 따른 고속 Stepped Hull 선형의 저항성능을 비교, 분석하였다. 시험결과, 2개의 스텝을 가지는 선형이 최소저항 선형임을 확인할 수 있었다.

• 대한조선학회논문집
• /
• 제51권6호
• /
• pp.521-529
• /
• 2014

In this study, numerical simulations and model tests are performed for the hull-form development of a G/T 29ton class coastal angling fishing boat. The numerical simulations are mainly used for the design of bow hull-form and the resistance performance is improved by the adoption of high bulbous bow. And, the resistance performances of the existing boat and the designed boat are verified by the model tests. The results of the experiments and calculations show that the effective power of the designed boat is 13.6% less than that of the existing boat at design speed. Therefore, the results of this research could be used as one of the fundamental data for the design of G/T 29ton class coastal angling fishing boat.

• 대한조선학회논문집
• /
• 제48권2호
• /
• pp.99-106
• /
• 2011

The appearance of CSR changes the concept of the hull form design as well as structural design, since the application of CSR inevitably brings the lightweight increase of a ship. Keeping the original design constraints such as principal particulars, deadweight, and speed performance, designers have to increase the volume of the hull form. As a result, the entrance angle at bow end should become larger, which results in blunter waterline shape. For a slow and full ship having high $C_B$ more than 0.85, a new concept of bow shape has been required to alleviate the increase of wave-making resistance, since it is very difficult to improve waterline and frameline shape for such a full ship. In this paper a new bow shape of Capesize Bulk Carrier was developed to improve its wave-making characteristics without incompliance with the design constraints. For loading manual calculation, NAPA software was used. FLUENT6.3.26 and WAVIS1.4 were used to evaluate resistance performance of the subject hull forms. The newly designed hull form was tested at SSPA model basin for the final confirmation of resistance and propulsion performance of the ship. It was found that the new bow shape of a Capesize Bulk Carrier improved the resistance characteristics greatly compared to a conventional bulbous bow. The other benefits of new bow shape on the manufacturability were also investigated.

• 해양환경안전학회지
• /
• 제6권2호
• /
• pp.33-46
• /
• 2000

As far as fishing vessels are concerned, there are two aspects to be noted: One is the stability which is the greatest concern for the safety of fishing vessels, as the corresponding number of casualty is overwhelming compared with those of other types of vessels. To flake it worse, the feature of casualty is rather catastrophic, accompanying major fatalities. The other aspect is related to the needs of improvement of resistance performance along with the hull form development. In particular, small fishing vessels, such as under 24m in length, which is dominant size in the type, need further scrutiny to enhance the qualities mentioned above, as relevant standards/criteria on the issues are not shown clearly and, therefore, implemented for the design or assessment.

• 대한조선학회논문집
• /
• 제52권4호
• /
• pp.290-297
• /
• 2015

This research is focusing on the added resistance and seakeeping ability of the designed passenger ship with gooseneck bulb(Designed hull) which provide the improvement of resistance performance under calm water condition. By comparing the added resistances and seakeeping abilities of the reference hull and the designed hull form with gooseneck bulb, it is confirmed that there is little difference in the operational comfort and the reduction of ship speed. As a result, the applied gooseneck bulb in this study is verified for the applicability to medium-sized passenger ships with a good resistance performance.

• 대한조선학회지
• /
• 제26권2호
• /
• pp.1-12
• /
• 1989

본 논문에서는 선체로부터 멀리 전파해 나아가는 선형파와 선체 가까이에 존재하는 쇄파로 인한 조파저항성분을 최소화시키는 방법을 보여준다. 본 방법은 선형조파저항의 최적화 방법과 시험자료 분석을 통한 쇄파저항의 통계적 최적화방법으로 구성된다. 응용목적으로서, 수선형상이 포물선이고 측면이 수직한 모형을 기본선형으로 택하였고, 선형파를 최적화하는 방법과 경험적인 방법을 통하여서 선체전반부의 횡단면적 곡선을 변화시킨 두척의 수정모형선을 얻었다. 3척의 선형에 대한 시험 및 분석결과로부터 선체전반부의 횡단면적 곡선의 변화에 따른 선형파저항과 쇄파저항과의 상관관계를 살펴보았다. 본 방법으로 선체전반부가 최적화된 선형은 설계속도($F_n=0.26$)에서 기본선형에 비하여 약 47%의 조파저항감소를 보이고 있다.

• 한국해양공학회지
• /
• 제29권3호
• /
• pp.217-223
• /
• 2015

In order to predict the motions of a planing hull in waves, it is necessary to accurately estimate the force components acting on the hull such as the hydrodynamic force, buoyancy, and friction, as well as the wave exciting force. In particular, based on strip theory, hydrodynamic forces can be estimated by the summation of the forces acting on each cross-section of the hull. A non-linear strip method for planing hulls was mathematically developed by Zarnick, and his formula has been used to predict the vertical motions of prismatic planing hulls in regular waves. In this study, several improvements were added to Zarnick's formula to predict the vertical motions of warped planing hulls. Based on calm water model test results, the buoyancy force and moment correction coefficients were modified. Further improvements were made in the pile-up correction. Pile-up correction factors were changed according to variations of the deadrise angles using the results found in previous research. Using the same hull form, captive model tests were carried out in other recent research, and the results were compared with the present calculation results. The comparison showed reasonably good agreements between the model tests and present calculations.